The 2016 Buick Encore with its 1.4L turbo is a compact crossover that suffers from catastrophic engine failures and chronic transmission cooling issues—both expensive, platform-defining problems that overshadow its otherwise decent packaging.
1.4L Turbo Catastrophic Engine Failure (Piston/Bearing/Ring Failure)
Common · high severityTypical onset: 60,000-100,000 mi
Symptoms: Heavy knocking or rattling from engine bay, especially cold start, Metal shavings in oil, glitter-like appearance on dipstick, Sudden loss of power, white or blue smoke from exhaust, Check engine light with misfire codes or low oil pressure warnings
Fix: This engine grenades itself due to piston ring land failures, spun bearings, or cracked pistons. Oil starvation from turbo oil consumption accelerates it. Complete engine replacement or rebuild required—15-20 labor hours for a salvage engine swap, 25-35 hours for full rebuild with machine work. Most shops recommend remanufactured long-block swap.
Estimated cost: $4,500-7,500
Transmission Oil Cooler Line Leaks and Cooler Failure
Common · high severityTypical onset: 50,000-90,000 mi
Symptoms: Transmission fluid pooling under vehicle, often pink or red, Transmission overheating warning on dash, Harsh shifts or slipping, especially when towing or in hot weather, Fluid cross-contamination if cooler inside radiator fails
Fix: The 6T40 transmission cooler lines corrode and leak at fittings, or the cooler itself fails inside the radiator causing fluid mixing. Requires cooler replacement, lines, full fluid flush. If coolant entered trans, complete trans rebuild needed. Cooler/lines alone: 3-4 hours. If trans damaged: 8-12 hours for rebuild or replacement.
Estimated cost: $800-1,200 (lines/cooler only), $2,800-4,200 (if trans rebuild required)
Transmission Mount Failure
Common · medium severityTypical onset: 40,000-80,000 mi
Symptoms: Clunking when shifting from park to drive or reverse, Excessive vibration at idle, especially with A/C on, Visible engine/trans movement when revving in park, Metallic banging over bumps from engine bay
Fix: The hydraulic transmission mount collapses or tears, letting the powertrain shift excessively. Common on these transverse FWD setups. Replace mount and inspect engine mounts while you're in there. 1.5-2 hours labor.
Estimated cost: $250-450
Turbocharger Oil Consumption and Turbo Seal Failure
Occasional · medium severityTypical onset: 70,000-110,000 mi
Symptoms: Burning one quart of oil every 1,000-2,000 miles, Blue smoke on hard acceleration or at startup, Loss of boost pressure, sluggish acceleration, Oil in intercooler or intake piping
Fix: Turbo seals fail, dumping oil into intake. Often compounded by PCV system issues causing crankcase pressure. Turbo replacement required—OEM or quality aftermarket. Remove intake, downpipe, coolant/oil lines. 5-7 hours. Address PCV valve at same time or it'll repeat.
Estimated cost: $1,400-2,200
Timing Belt Tensioner and Water Pump Failure
Occasional · high severityTypical onset: 80,000-120,000 mi
Symptoms: Squealing or grinding noise from front of engine, Coolant leak from timing cover area, Engine overheating or temp fluctuations, Check engine light with cam/crank correlation codes
Fix: This is a timing BELT engine (not chain). Tensioner seizes or water pump behind timing cover leaks. If belt jumps or breaks, valves meet pistons—engine destroyed. Mandatory replacement at 97,500 miles per GM, but failures happen earlier. Belt kit + water pump + tensioner: 6-8 hours labor.
Estimated cost: $900-1,400
Fuel Injector Failure and Carbon Buildup (Direct Injection)
Occasional · medium severityTypical onset: 60,000-100,000 mi
Symptoms: Rough idle, misfires on cold start that clear after warmup, Check engine light with cylinder misfire codes, Poor fuel economy, hesitation on acceleration, Failed emissions testing
Fix: Direct injection means no fuel washing intake valves—carbon accumulates and injectors clog. Walnut-blasting intake valves (3-4 hours) addresses carbon. Failed injectors need replacement individually (~1 hour each) or all four as a set (2.5 hours). Top-tier fuel and catch can help prevent.
Estimated cost: $600-900 (walnut blast), $450-800 (injector set)
Hard pass unless under $6,000 with full service records and recent timing belt—the engine failure rate and transmission issues make this a financial gamble most used buyers should avoid.
AI-assisted summary drawn from NHTSA recall data, our labor-times database, and platform knowledge. Not a substitute for a pre-purchase inspection on a specific vehicle.