1978 CHRYSLER NEWPORT

360ci V8RWDAUTOMATICgas
5-Year Cost of Ownership
$41,070 maintenance + known platform issues
~$8,214/yr · 680¢/mile equivalent · $37,703 maintenance + $2,667 expected platform issues
Compare this engine
vs
318ci V8
vs
400ci V8
vs
440ci V8
Common Problems & Known Issues

The 1978 Chrysler Newport is a full-size C-body platform with solid Mopar V8 engines, but suffers from lean-burn emission system failures, aging rubber components, and the typical Chrysler electronic voltage regulator issues of this era.

Lean Burn System Failures (318/360 engines)

Common · medium severity
Typical onset: 60,000-120,000 mi
Symptoms: Hard starting when warm or cold, Hesitation and stumbling during acceleration, Stalling at idle or when coming to a stop, Check engine light or no-start with spark issues
Fix: The Lean Burn computer and pickup coil assembly fail frequently. Most techs convert to traditional points or electronic ignition with aftermarket kit. Computer replacement alone runs 2-3 hours labor, full conversion 3-4 hours.
Estimated cost: $400-800

Timing Chain Stretch and Gear Wear

Common · high severity
Typical onset: 80,000-140,000 mi
Symptoms: Rattling noise from front of engine on cold start, Loss of power and poor fuel economy, Backfiring through carburetor, Engine runs but timing is severely retarded
Fix: All these V8s use nylon-coated timing gears that deteriorate. Timing set replacement requires front cover removal, new chain, gears, and seal. Book time 5-6 hours, more if you find worn cam or crank gears requiring machine work.
Estimated cost: $650-1,200

Electronic Voltage Regulator Failure

Common · medium severity
Symptoms: Battery light on or flickering, Overcharging (above 15 volts) or undercharging, Dead battery after sitting overnight, Ammeter showing extreme discharge or charge
Fix: The electronic regulator mounted on firewall or inner fender fails from heat and corrosion. Simple bolt-on replacement takes 0.5 hours, but diagnosis can add time if alternator is also suspect.
Estimated cost: $120-250

Carburetor Issues (Carter Thermoquad or Holley 2280)

Occasional · medium severity
Typical onset: 70,000-100,000 mi
Symptoms: Poor idle quality and hunting, Flooding or fuel leaking from base, Rough acceleration with flat spots, Excessive fuel consumption
Fix: The Thermoquad plastic fuel bowls warp, and both carbs suffer from aged accelerator pump diaphragms and warped gaskets. Rebuild kits available but proper rebuild requires 3-4 hours for cleaning, setting float levels, and adjustment. Many shops just swap for a basic Edelbrock.
Estimated cost: $350-700

Transmission Torque Converter Lockup Failures (A-727 with lockup)

Occasional · medium severity
Typical onset: 90,000-130,000 mi
Symptoms: Shuddering during highway cruise around 45-55 mph, Check engine light related to lockup solenoid, Transmission overheating on long trips, No lockup engagement, higher RPM at cruise
Fix: The lockup torque converter and solenoid system added in '78 fails frequently. Solenoid replacement is 2 hours with pan drop, but if converter clutch is burnt, it's a transmission-out job at 8-10 hours.
Estimated cost: $300-2,200

Front Torsion Bar Suspension Wear

Common · medium severity
Typical onset: 80,000-120,000 mi
Symptoms: Clunking over bumps from front end, Uneven tire wear on inside edges, Wandering steering and poor alignment retention, Vehicle sits lower on one side
Fix: Upper and lower ball joints, control arm bushings, and sway bar links wear out. Complete front end rebuild with alignment takes 6-8 hours. Torsion bars rarely fail but adjusters seize.
Estimated cost: $800-1,400

Fuel Tank Sending Unit and Pump Failure

Occasional · low severity
Symptoms: Fuel gauge reads empty or full constantly, Erratic gauge movement, Fuel starvation or no-start despite fuel in tank, Visible rust in fuel filter
Fix: Tank-mounted sending units corrode and in-tank sock filters clog with sediment from 45-year-old tanks. Requires tank drop, 2-3 hours labor. If tank has internal rust, replacement recommended.
Estimated cost: $350-900
Owner tips
  • Replace the Lean Burn system early with an aftermarket electronic ignition conversion to avoid constant driveability issues
  • Change timing chain preventively at 80k if history unknown—nylon gear teeth shed into oil pan and cause catastrophic damage
  • Keep electronic voltage regulator and ballast resistor spares in the glovebox—both fail without warning
  • Flush cooling system and replace all rubber hoses—original hoses collapse internally causing overheating
  • Use Lucas or similar oil additive to quiet lifter tick common on high-mileage 318/360 engines with worn camshafts
Buy one if you find a solid body with maintenance records and are comfortable with carburetor tuning—mechanically simple once you eliminate the troublesome Lean Burn system, but parts availability is declining.
AI-assisted summary drawn from NHTSA recall data, our labor-times database, and platform knowledge. Not a substitute for a pre-purchase inspection on a specific vehicle.
593 jobs across 17 categories
Building an app?
Free API access to all this data — 50 requests/day, no card required.
Get an API key →
Run a shop?
Manage repairs, estimates, and customers with ShopBase — $249/mo, all features included. Built by the same team.
Try ShopBase →