2009 SUBARU WRX

2.5L Turbo H4AWDMANUALgasturbo
5-Year Cost of Ownership
$49,347 maintenance + known platform issues
~$9,869/yr · 820¢/mile equivalent · $36,978 maintenance + $9,769 expected platform issues
Compare this engine
vs
2.4L Turbo H4
vs
2.0L Turbo H4
Common Problems & Known Issues

The 2009 WRX is a highly modifiable turbocharged platform that suffers from two major failure modes: owner abuse (aftermarket tunes, money shifts, overheating) and inherent EJ25 turbo weaknesses—ringland failures and head gasket leaks. Clean, stock examples can be reliable; modified or hard-driven cars are time bombs.

Ringland Failure (Piston #4)

Common · high severity
Typical onset: 60,000-100,000 mi
Symptoms: Misfires on cylinder 4, rough idle, flashing CEL, Loss of compression on #4 (leakdown test confirms), Metal debris in oil, visible on drain plug magnet, Knocking or rattling from engine under load
Fix: Full short block replacement or engine rebuild with forged pistons. Pulling motor, disassembly, machine work, reassembly with upgraded internals. 20-30 labor hours if you're doing it right with forged components.
Estimated cost: $4,500-8,000

Head Gasket Failure (External Oil Leaks)

Common · medium severity
Typical onset: 80,000-120,000 mi
Symptoms: Oil seepage on block between heads and block, visible from below, Oil smell after driving, drips on driveway, Low oil level between changes, Not typically coolant-into-oil like NA EJ25s—this is external weeping
Fix: Pull engine (required for proper access on turbo cars), resurface heads if warped, OEM multi-layer steel gaskets, ARP studs recommended. 16-20 labor hours with motor pull.
Estimated cost: $2,500-4,000

Turbocharger Failure

Occasional · high severity
Typical onset: 100,000-140,000 mi
Symptoms: Blue smoke on startup or under boost, Loud whining or grinding noise from turbo, Loss of boost pressure, sluggish acceleration, Oil in intercooler pipes or intake, Shaft play measurable with turbo hot side removed
Fix: OEM IHI VF52 turbo replacement or upgrade to aftermarket. If oil-starved failure, flush oil system and check banjo bolt filters. 6-8 labor hours for swap.
Estimated cost: $1,800-3,500

Transmission Synchro Wear (2nd Gear)

Common · medium severity
Typical onset: 70,000-110,000 mi
Symptoms: Grinding or crunching into 2nd gear, especially when cold, Difficulty engaging 2nd under aggressive shifts, Synchro grind even with proper rev-matching, May also affect 3rd gear on heavily-driven cars
Fix: Transmission removal, teardown, synchro ring replacement, new fluid. 8-12 labor hours. Many owners upgrade to OEM STI transmission at this point instead.
Estimated cost: $1,500-2,800

Banjo Bolt Filter Clogging (Turbo Oil Feed)

Occasional · high severity
Symptoms: Turbo failure from oil starvation, Often discovered post-mortem after turbo grenades, No direct symptoms until turbo dies, Preventive inspection shows restricted mesh screens
Fix: Remove banjo bolts on turbo oil feed line, clean or replace filter screens. Many techs remove screens entirely for track cars. 0.5 labor hours preventive, but damage is done if you're inspecting after failure.
Estimated cost: $50-150

Front Wheel Bearing Failure

Occasional · medium severity
Typical onset: 80,000-130,000 mi
Symptoms: Humming or growling noise that increases with speed, Noise changes pitch in turns (louder on load side), Vibration through steering wheel at highway speeds, ABS/traction light may illuminate if sensor damaged
Fix: Replace hub/bearing assembly. Front bearings pressed into knuckle—requires hydraulic press or knuckle swap with new bearing installed. 2-3 labor hours per side.
Estimated cost: $400-700

Throwout Bearing Noise

Common · low severity
Typical onset: 50,000-90,000 mi
Symptoms: Chirping or squealing with clutch pedal depressed, Noise disappears when pedal released, No clutch slip or engagement issues initially, Gets progressively louder over time
Fix: Replace throwout bearing and clutch assembly while transmission is out. Since labor is 6-7 hours for trans removal, always replace clutch, pressure plate, TOB, and pilot bearing together.
Estimated cost: $1,200-2,000
Owner tips
  • Change oil every 3,500-4,000 mi with quality 5W-30 synthetic—these motors are hard on oil from blow-by and heat.
  • Inspect banjo bolt filters at 60k mi preventively; consider removal if car sees track use.
  • Run OEM-spec 91+ octane fuel and avoid aggressive tuning without supporting fuel system mods.
  • Walk away from any car with aftermarket tune or intake/exhaust mods unless you have full service records and compression test results.
  • Check for oil seepage around heads during pre-purchase inspection—external HG leaks are wear items on this motor.
  • Let turbo idle 30-60 seconds before shutdown after hard driving to prevent coking oil in turbo CHRA.
Buy only if bone-stock with documented maintenance and compression test results—modified examples or unknown-history cars are engine rebuild candidates waiting to happen.
AI-assisted summary drawn from NHTSA recall data, our labor-times database, and platform knowledge. Not a substitute for a pre-purchase inspection on a specific vehicle.
593 jobs across 17 categories
Building an app?
Free API access to all this data — 50 requests/day, no card required.
Get an API key →
Run a shop?
Manage repairs, estimates, and customers with ShopBase — $249/mo, all features included. Built by the same team.
Try ShopBase →