The 2007 Ram 1500 is a workhorse truck that suffers primarily from transmission cooler failures, ball joint wear, and Hemi-specific issues like lifter tick and exhaust manifold bolt failures. Overall durability is decent if you stay on top of known weak points.
Transmission Cooler Line / Radiator Failure
Common · high severity
Typical onset: 80,000-150,000 mi
Symptoms: Pink milky fluid in transmission or coolant overflow, Transmission slipping or delayed engagement after coolant contamination, Coolant in transmission pan during fluid service
Fix: The factory cooler inside the radiator fails and cross-contaminates coolant and ATF, destroying the transmission. Fix requires radiator replacement, transmission flush (if caught early), or full transmission rebuild/replacement if contamination went unnoticed. External auxiliary cooler install is mandatory to prevent repeat failure. 8-15 hours labor depending on transmission damage.
Estimated cost: $800-5,500
Front Ball Joints and Tie Rod Ends
Common · high severity
Typical onset: 60,000-100,000 mi
Symptoms: Clunking or popping over bumps, Wandering steering or excessive play in wheel, Uneven tire wear on inside or outside edges, Steering wheel vibration at highway speeds
Fix: Upper and lower ball joints wear prematurely, especially on 4WD models. Tie rod ends follow close behind. Both are safety-critical steering components. Most shops replace upper/lower ball joints as pairs per side and tie rod ends as a set. 4-6 hours labor for full front-end rebuild with alignment.
Estimated cost: $800-1,400
Hemi Lifter Tick / Cam/Lifter Failure (5.7L only)
Common · medium severity
Typical onset: 50,000-120,000 mi
Symptoms: Cold-start ticking that may or may not go away when warm, Check engine light with misfire codes, Loss of power or rough idle if cam lobe is wiped, Metal shavings in oil on analysis
Fix: MDS (cylinder deactivation) lifters fail or stick, causing tick and eventually cam lobe wear. Oil changes every 3-4k miles help but don't prevent it entirely. Repair requires both heads off, cam replacement, full lifter set, and often pushrods. 16-20 hours labor.
Estimated cost: $3,500-5,500
Exhaust Manifold Bolt Failure (5.7L Hemi)
Common · low severity
Typical onset: 70,000-130,000 mi
Symptoms: Exhaust leak ticking on cold start, louder under load, Smell of exhaust in cabin, Visible broken stud on manifold
Fix: The Hemi manifold bolts snap due to heat cycling. Typically middle bolts on driver or passenger side. Requires manifold removal and stud extraction/retapping or Heli-Coil inserts. 3-5 hours per side labor. Often both sides need attention eventually.
Estimated cost: $600-1,200
EVAP Purge Valve and Leak Detection Pump
Occasional · low severity
Typical onset: 80,000-140,000 mi
Symptoms: Check engine light with P0441, P0455, P0456 codes, Difficulty filling fuel tank (clicks off repeatedly), Fuel smell near tank or engine bay
Fix: The EVAP system is overly complex on these trucks. Purge valve sticks or leak detection pump (LDP) fails. Smoke test usually required to pinpoint leaks in lines. Purge valve is 0.5 hours, LDP is 1.5 hours, but diagnosis can add time if multiple components are suspect.
Estimated cost: $250-700
Dashboard Cracking
Common · low severity
Symptoms: Cracks along top of dash near windshield, especially in sun-belt states, Warping or separation of dash cover
Fix: Not a mechanical failure, but extremely common cosmetic defect due to poor materials. Dash replacement requires full removal (10-12 hours), most owners live with it or use a cover. Replacement dash often cracks again.
Estimated cost: $800-1,500
Rear Differential Pinion Seal Leak
Occasional · medium severity
Typical onset: 90,000-150,000 mi
Symptoms: Gear oil dripping from front of differential, Low fluid causes whining or howling from rear axle under load
Fix: Pinion seal leaks are common on higher-mileage trucks. Requires driveshaft removal, pinion nut torque setup, and seal replacement. If caught early, 2-3 hours labor. If run low on fluid, ring and pinion damage requires full differential rebuild (8+ hours).
Estimated cost: $350-2,200
Owner tips
Install an external transmission cooler immediately if it doesn't have one — the factory radiator-integrated cooler is a ticking time bomb
On 5.7L Hemis, run full synthetic oil and change every 3-4k miles to延长 lifter life; avoid long idle times
Inspect ball joints and tie rods every oil change after 50k miles — worn parts cause tire eating and are dangerous
Check exhaust manifold bolts annually on Hemis; catch broken studs early before they worsen
Solid truck if transmission cooler is addressed and you budget for ball joints and Hemi quirks — avoid high-mileage Hemis with unknown maintenance history.
AI-assisted summary drawn from NHTSA recall data, our labor-times database, and platform knowledge. Not a substitute for a pre-purchase inspection on a specific vehicle.
Be the first to unlock repairs for the 2007 Dodge Ram 1500
Procedures haven't been generated for this vehicle yet. Become the founding sponsor and we'll generate expert-grade, step-by-step repair walkthroughs for every common job on it — free for every mechanic and DIYer who looks it up after, forever.
AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE · 16V352000
2016-05-24 · EA15001
Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A."
Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B."
Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.
Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.
AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE · 15V313000
2015-05-27 · EA15001
Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.
ELECTRICAL SYSTEM:IGNITION:SWITCH · 14V795000
2014-12-16 · PE14013
Chrysler Group LLC (Chrysler) is recalling certain model year 2006-2007 Dodge Ram 1500, 2500, 3500, Dakota, and 2006 Mitsubishi Raider vehicles manufactured July 1, 2005, to July 31, 2006 with manual transmissions. The return springs in the clutch ignition interlock switch may break.
Consequence: Broken springs can result in a no-start condition, or cause unintended movement when the ignition is cranked, increasing the risk of a vehicle crash.
Remedy: Chrysler will notify owners, and dealers will replace the clutch ignition interlock switch, free of charge. The recall began on March 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P80.
STEERING:LINKAGES:TIE ROD ASSEMBLY · 13V528000
2013-11-06
Chrysler Group LLC (Chrysler) is recalling certain model year 2003-2008 Dodge RAM 2500 4x4 and 3500 4x4, model year 2007-2008 Dodge RAM 3500 4x2 Cab Chassis and model year 2006-2008 Dodge RAM 1500 Mega Cab 4x4 trucks manufactured February 12, 2002, through February 13, 2008. The left tie rod assembly may break.
Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.
Remedy: Chrysler notified owners and launched its recall campaign in January 2014. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N62.
WHEELS:HUB · 10E040000
2010-08-23
FEDERAL-MOGUL IS RECALLING CERTAIN CARQUEST, NATIONAL, AND PERCISION BRAND WHEEL HUB ASSEMBLIES, P/NOS 515073 AND 515073, SOLD FOR USE AS REPLACEMENT EQUIPMENT ON MODEL YEAR 2002 THROUGH 2008 DODGE RAM 1500 PICKUP TRUCKS. THE INBOARD ROLL FORM USED TO MAINTAIN THE HUB ASSEMBLY CAN FATIGUE RESULTING IN NOISE AND/OR WHEEL SEPARATION ON THE TWO WHEEL DRIVE (2WD) APPLICATIONS. THE RISK OF THESE ISSUES DO NOT OCCUR ON THE FOUR WHEEL DRIVE (4WD) APPLICATIONS, AND INSTALLATION ON THE 4WD APPLICATIONS ARE NOT PART OF THIS RECALL.
Consequence: A VEHICLE CRASH CAN OCCUR IF THE WHEEL SEPARATES FROM THE VEHICLE.
Remedy: FEDERAL-MOGUL WILL NOTIFY OWNERS OF RECORD AND TECHNICIANS WILL REPLACE THE AFFECTED HUB ASSEMBLIES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT FEDERAL-MOGUL AT 1-877-489-6659.
STEERING:GEAR BOX:SHAFT PITMAN · 10E013000
2010-05-03
FABTECH IS RECALLING CERTAIN AFTERMARKET REPLACEMENT PITMAN ARMS, P/NOS. FTS93001 AND FT44039, INSTALLED FOR USE ON CERTAIN 2003 THROUGH 2008 DODGE 2500 4WD, 3500 4WD, AND 1500 4WD MEGA CAB VEHICLES. THE PITMAN ARM CAN FRACTURE AND BREAK AWAY FROM THE STEERING BOX CAUSING TOTAL LOSS OF STEERING CONTROL.
Consequence: STEERING LOSS COULD RESULT IN A VEHICLE CRASH POSSIBLY RESULTING IN PROPERTY DAMAGE, INJURY OR DEATH.
Remedy: FABTECH WILL NOTIFY OWNERS AND AUTHORIZED INSTALLERS WILL INSPECT FOR DEFECTIVE PITMAN ARM AND REPLACE IF NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 24, 2010. OWNERS MAY CONTACT FABTECH AT 1-877-432-2832.
VISIBILITY:GLASS, SIDE/REAR · 07E104000
2007-12-11
CERTAIN CURVED TEMPERED REPLACEMENT GLASS MANUFACTURED BY HANGZHOU SAFETY GLASS LTD AND SUPPLIED TO SAFELITE BY AUTO TEMP INC., IDENTIFIED AS DOT-430, AND SOLD FOR USE ON CERTAIN DOMESTIC AND FOREIGN VEHICLES MAY NOT BREAK INTO SMALL PIECES AS EXPECTED OF TEMPERED GLASS AND FAILS TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 205, "GLAZING MATERIALS."
Consequence: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANT(S) MAY BE SERIOUSLY INJURED BY SHATTERED GLASS.
Remedy: SAFELITE WILL NOTIFY ITS RETAIL CUSTOMERS AND REPLACE THE GLASS FREE OF CHARGE. RETAIL CUSTOMERS CAN CONTACT SAFELITE TOLL FREE AT 1-888-843-2906. SAFELITE WILL NOTIFY ITS WHOLESALE CUSTOMERS AND REIMBURSE WHOLESALE CUSTOMERS FOR CURRENT INVENTORY AND AT A SPECIFIED RATE FOR REPLACING THEIR CUSTOMER'S GLASS. WHOLESALE CUSTOMERS CAN CONTACT SAFELITE'S WHOLESALE DIVISION, SERVICE AUTOGLASS TOLL FREE AT 1-888-246-6298. THE RECALL BEGAN ON JANUARY 15, 2008.
Building an app?
Free API access to all this data — 50 requests/day, no card required.