Home/Torque Specs/Dodge/Challenger/2019-2019 6.2L V8 Hellcat (707hp)/Engine Rebuild

2019-2019 Dodge Challenger Engine Rebuild Torque Specs

6.2L V8 Hellcat (707hp)

The 2019 Dodge Challenger is equipped with a 6.2L V8 engine. Below you'll find detailed engine rebuild torque specifications information including labor time estimates, cost ranges, and technician notes specific to this engine configuration.

Share:X FB

Labor Time:30 hours

View Labor Time Details →

🔧 Torque Values25 specifications

Component	lb-ft	Nm	Notes
⚠️ Balance Shaft Bolts	18	25	—
⚠️ Camshaft Bearing Cap Bolts	10	14	Tighten in sequence, 3 passes
⚠️ Camshaft Cap Bolts	10	14	Tighten in sequence from center outward, multiple passes
⚠️ Connecting Rod Bolts	33	45	TTY - critical torque plus angle
Cover Bolts	16	22	—
⚠️ Crankshaft Pulley Bolt	133	180	Often TTY - check spec, may require impact
⚠️ Cylinder Head Bolts	48	65	TTY - tighten in sequence plus angle
Electrical Connector Bolts	7	9	—
⚠️ Exhaust Manifold Nuts	22	30	Apply anti-seize, work hot-to-cold
⚠️ Flywheel Bolts	70	95	Often TTY, tighten in star pattern
⚠️ Gasket Bolts	20	27	—
⚠️ Gasket Surface Bolts	20	27	Clean mating surfaces
⚠️ Intake Manifold Bolts	18	25	—
⚠️ Main Bearing Cap Bolts	55	75	TTY - tighten in sequence plus angle
⚠️ Mounting Bolts	47	64	—
⚠️ Oil Drain Plug	26	35	Use new crush washer
⚠️ Oil Pan Bolts	9	12	Tighten in sequence
⚠️ Oil Pump Bolts	9	12	—
⚠️ Oil Pump Pickup Tube	9	12	—
Sensor Bolts	11	15	—
Sensor Mounting Bolts	11	15	—
⚠️ Timing Chain Guide Bolts	9	12	Replace if worn
⚠️ Timing Chain Tensioner Bolt	18	25	Install with pin/clip to compress
⚠️ Timing Cover Bolts - 8mm	18	25	Tighten in sequence
Valve Cover Bolts	7	10	Tighten in sequence

⚠️ = Critical torque value | Always verify with vehicle-specific service manual

⚠️ Some critical specs are estimated. Please verify sequence.

Other Jobs with Torque Specs

Engine Rebuild Torque Specs on Other Vehicles

Acura CL

1997-1997 2.2L I4

Acura CL

1997-1997 3.0L V6

Acura CL

1998-1998 2.2L I4

Acura CL

1998-1998 3.0L V6

Acura CL

1999-1999 2.2L I4

Acura CL

1999-1999 3.0L V6

Common Questions

What is the torque spec for engine rebuild on a 2019-2019 Dodge Challenger?

The primary torque specification for engine rebuild on a 2019-2019 Dodge Challenger is 25 Nm (18 lb-ft).

How many torque specs are there for Dodge Challenger engine rebuild?

There are 25 torque specifications for engine rebuild on the 2019-2019 Dodge Challenger 6.2L V8 Hellcat (707hp), covering all related fasteners and components.

Last updated: March 2026

View Labor Times | View Fluid Specs | View DTC Codes