1973 PLYMOUTH SATELLITE

Typical onset: 80,000-150,000 mi

Symptoms: Hard starting when engine is cold, improves when warm, Rough idle with occasional backfiring through carburetor, Rattling noise from timing cover on cold startup, Loss of power and poor fuel economy, Check timing and it keeps drifting retarded

Fix: Replace timing chain, gears, and tensioner—essential to replace the nylon-toothed cam gear as the teeth strip with age. Requires front accessories removal, harmonic balancer puller, and timing cover R&R. Budget 4-6 hours labor depending on V8 vs. slant-six and accessory complications. The 225 slant-six is actually easier access than the V8s.

Estimated cost: $400-800

Symptoms: Chronic hard starting hot or cold, Stumbling, hesitation, or stalling during acceleration, Black smoke from exhaust indicating rich condition, Vacuum leaks at multiple connection points, Failed EGR valve causing ping or poor idle

Fix: The 1973 model year introduced complex emissions equipment that's now 50+ years old. Carter or Holley carbs have worn throttle shafts, deteriorated gaskets, and gunked passages. Often needs complete carburetor rebuild or replacement plus new vacuum lines throughout. The rat's nest of vacuum-operated emissions devices frequently fails. Many owners simplify the system during restoration. Plan 3-5 hours for proper carburetor rebuild and vacuum system overhaul.

Estimated cost: $350-900

Typical onset: 60,000-120,000 mi

Symptoms: Front end sits low with reduced ground clearance, Clunking over bumps from worn lower control arm bushings, Wandering steering and poor handling, Uneven tire wear on front, Upper control arm bushings completely deteriorated

Fix: Torsion bars themselves rarely fail but the bushings, ball joints, and adjustment hardware wear badly. Lower control arm pivot bushings are notorious for failure. Upper ball joints tend to wear faster than lowers. Complete front-end rebuild includes ball joints (uppers and lowers), control arm bushings, tie rod ends, idler arm, and torsion bar adjusters. Figure 8-12 hours for complete overhaul with alignment.

Estimated cost: $1,200-2,200

Symptoms: Fuel smell inside cabin or under car, Hard starting after sitting overnight, Engine stumbling or dying after warmup, Visible fuel seepage at tank, lines, or pump, Fuel gauge erratic or non-functional

Fix: After 50 years, rubber fuel lines are cracked, steel lines are rusted (especially at the rear axle), and the sending unit gasket leaks. The mechanical fuel pump diaphragm often deteriorates. Tank itself frequently rusts through at the top where water collects. Proper fix involves tank removal, replacement or professional cleaning/sealing, new sending unit, all new lines from tank to pump to carb, and new pump. Budget 6-10 hours depending on line routing complexity and tank condition.

Estimated cost: $600-1,400

Symptoms: Alternator not charging or intermittent charging, Voltage regulator causes overcharging or undercharging, Headlights dim or flicker, Ammeter shows constant discharge, Bulkhead connector melting or causing voltage drop

Fix: The notorious Mopar bulkhead connector develops high resistance and overheats, causing multiple electrical gremlins or even fire risk. Alternator brushes wear and voltage regulators fail—electronic regulators are more reliable than the original mechanical units. Wiring harness insulation gets brittle. Properly addressing means bulkhead connector bypass or professional repair, alternator rebuild, electronic voltage regulator upgrade, and selective wire repairs. 4-8 hours depending on depth of issues.

Estimated cost: $400-1,000

Typical onset: 70,000-130,000 mi

Symptoms: Transmission doesn't downshift for passing, Delayed or soft shifts under acceleration, Early upshifts with sluggish performance, Worn linkage bushings visible at firewall or carburetor

Fix: The Torqueflite 727 or 904 automatics are bulletproof, but the external kickdown linkage wears at pivot points and adjustment slips. Bushings get sloppy and the rod can bind. Proper adjustment is critical for transmission longevity and performance. Replacement bushings and proper setup takes 1-2 hours. Many rigs have this incorrectly adjusted, causing premature clutch wear.

Estimated cost: $150-350