1977 AMC HORNET

258ci I6RWDgas
5-Year Cost of Ownership
$14,050 maintenance + known platform issues
~$2,810/yr · 230¢/mile equivalent · $7,723 maintenance + $5,627 expected platform issues
Compare this engine
vs
232ci I6
vs
304ci V8
Common Problems & Known Issues

The 1977 AMC Hornet is a simple, body-on-frame compact that's generally reliable when maintained, but suffers from well-documented automatic transmission failures, timing chain wear on the inline-six engines, and rust issues that compromise structural integrity in the Northeast and Midwest.

Torque-Command 998/904 Automatic Transmission Failure

Common · high severity
Typical onset: 80,000-120,000 mi
Symptoms: Slipping between gears, especially 2nd to 3rd, Delayed engagement when shifting into Drive or Reverse, Burnt transmission fluid smell and dark red/brown fluid, Loss of all forward gears (complete clutch pack failure)
Fix: Full rebuild required in most cases — torque converter, clutch packs, seals, and bands. Rebuilds take 8-12 hours including R&R. The transmission oil cooler frequently clogs with debris from failing clutches, so cooler replacement and line flushing is mandatory during rebuild or you'll be back in 6 months.
Estimated cost: $1,800-2,800

Timing Chain Stretch and Gear Wear (232/258 I6)

Common · medium severity
Typical onset: 100,000-140,000 mi
Symptoms: Rattling noise from front of engine on cold start that fades after 30 seconds, Loss of power and poor fuel economy, Rough idle and difficulty starting when hot, Check timing — often retarded 8-12 degrees from wear
Fix: Timing cover removal, chain and gear set replacement, front seal. The AMC I6 uses a nylon-toothed cam gear that deteriorates. Plan 6-8 hours labor. While you're in there, replace the oil pump if it has any slop — they're known to lose pressure past 120k.
Estimated cost: $800-1,400

Floor Pan and Frame Rail Rust-Through

Common · high severity
Symptoms: Visible holes in driver/passenger floor pans, Soft or flaking metal around rear spring mounts, Fuel tank strap corrosion causing tank sag, Rear leaf spring shackle mounts rusted through body
Fix: This is not a repair job for most shops — it's welding sheet metal patches or replacement floor sections. Front torque boxes rust from inside out. Rear spring hangers can separate from the body entirely. Expect 15-25 hours for proper floor pan replacement with rust treatment. Many cars are totaled over this.
Estimated cost: $2,000-4,500

Valve Cover and Oil Pan Leaks Leading to Rear Main Seal Failure

Common · medium severity
Typical onset: 60,000-100,000 mi
Symptoms: Oil drips from bell housing area, Oil-soaked starter motor, Puddles under engine after sitting overnight, Blue smoke on startup from oil dripping onto exhaust
Fix: AMC inline-sixes leak from every gasket surface. The rear main seal is a rope-style that requires transmission removal (6-8 hours total). Here's the kicker: if you don't fix the valve cover and oil pan leaks first, oil migrates back along the block and makes the new rear main fail within 10k miles. Do them all at once.
Estimated cost: $900-1,600

Carter BBD Carburetor Accelerator Pump and Float Issues

Occasional · low severity
Symptoms: Hesitation or stumble on acceleration from stop, Engine floods and is difficult to start when hot, Fuel smell in engine bay, visible leaking around bowl gasket, Poor fuel economy — below 12 mpg city
Fix: The Carter BBD is simple but the accelerator pump diaphragm hardens with age and the float often develops pin holes causing flooding. Rebuild kits are $40 and take 2-3 hours for someone who knows these carbs. Most shops will recommend replacement with a remanufactured unit (4 hours labor) because adjustments are touchy.
Estimated cost: $300-600

Front Upper Control Arm Bushings and Ball Joint Wear

Occasional · medium severity
Typical onset: 70,000-110,000 mi
Symptoms: Clunking over bumps from front suspension, Wandering steering and poor return to center, Uneven tire wear on inside edges, Visible play when prying on ball joints with bar
Fix: AMC used a trunnion-style front suspension. Upper control arm bushings dry out and crack. Ball joints are riveted in — replacement requires drilling out rivets and bolting in new units. Figure 4-5 hours for both sides including alignment. If the steering box is also worn (common), add another $400-700 for rebuild or replacement.
Estimated cost: $700-1,200
Owner tips
  • Change transmission fluid every 25k miles with the correct Dexron — these transmissions are sensitive to fluid condition
  • Inspect timing chain slack every 50k after 80k miles; if you can twist the crank 15+ degrees before the cam moves, you're on borrowed time
  • Undercoat and fluid-film the floor pans and frame rails annually if you're in the rust belt — these cars dissolve from the inside out
  • The 258 I6 is nearly bulletproof if you keep oil in it and address the timing chain before 140k; the 304 V8 is thirsty and no faster in this chassis
  • Keep a rebuild kit for the Carter BBD in your toolbox — they're cheap insurance and 30 minutes with a screwdriver beats a tow
Buy one if rust-free and the transmission shifts cleanly — otherwise you're looking at $3k-5k in immediate work on a $3k car.
AI-assisted summary drawn from NHTSA recall data, our labor-times database, and platform knowledge. Not a substitute for a pre-purchase inspection on a specific vehicle.
596 jobs across 18 categories
Building an app?
Free API access to all this data — 50 requests/day, no card required.
Get an API key →
Run a shop?
Manage repairs, estimates, and customers with ShopBase — $249/mo, all features included. Built by the same team.
Try ShopBase →