Free API
hvac

AC Compressor Oil Add

for 2009 Aston Martin DB9 6.0L V12 · RWD
Difficulty
Moderate
Time
30 min
Tools
6
Steps
8
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

Add PAG oil to the AC compressor to maintain proper lubrication without removing the compressor from the vehicle.

Warnings

⚠️AC system operates under high pressure (up to 350 psi). Wear eye protection and gloves at all times. Never disconnect fittings with pressure in the system.
⚠PAG oil is hygroscopic and absorbs moisture rapidly. Keep containers sealed until use and minimize exposure to air.
⚠Adding too much oil will reduce AC cooling efficiency and can damage the compressor. Add only the amount removed during service or as specified for oil loss scenarios.
ℹ️The 2009 DB9 AC system typically uses PAG 46 oil. Verify specification in owner documentation before adding oil.

Tools required

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Fluids

  • PAG 46 or PAG 100 AC compressor oil — 0.125 qt

Preparation

  1. Park vehicle on level ground and apply parking brake
  2. Turn off engine and allow AC system to stabilize (minimum 10 minutes)
  3. Verify AC system refrigerant charge is low or has been recovered - do not add oil to a fully charged system without proper recovery
  4. Determine the amount of oil to add: typically 1-2 oz (30-60 ml) for minor top-off, or consult service history if components were replaced
  5. Ensure PAG oil viscosity matches system specification (PAG 46 is standard for DB9)
  6. Locate AC service ports on the suction and discharge lines near the front of the engine bay

Procedure

  1. 1
    Verify system pressure and refrigerant status
    Connect AC manifold gauge set to the low-pressure (larger diameter) and high-pressure service ports. Check that system pressure is near zero or has been properly evacuated. If system contains refrigerant, it must be recovered by certified equipment before adding oil. Record current pressure readings.
  2. 2
    Prepare oil injection tool
    Fill the PAG oil injector tool or syringe adapter with the exact amount of fresh PAG oil determined from service history or component oil-loss specification. Only use a 1-2 oz estimate when no better data is available. Ensure the tool is clean and free of contaminants. Keep the oil container sealed when not in use to prevent moisture absorption. Ensure the tool is clean and free of contaminants. Keep the oil container sealed when not in use to prevent moisture absorption.
  3. 3
    Connect oil injector to low-side service port
    Remove the low-side service port cap. Attach the oil injector tool to the low-pressure service port (identified by its larger-diameter quick-connect fitting; verify port location against the vehicle service documentation). Ensure a secure connection to prevent air ingress during oil addition.
  4. 4
    Inject PAG oil into system
    With the system under vacuum (established via the vacuum pump in the evacuation step), slowly open the injector to allow the measured PAG oil to be drawn into the low-side port automatically. Do NOT inject oil into a system at atmospheric pressure, as this risks air and moisture ingress. Meter the oil in slowly over 30-60 seconds to prevent foaming. Note: After the system has been evacuated (see step 6), slowly draw the measured PAG oil in through the low-side port; the system vacuum will pull the oil in automatically. Do not inject oil into a system at atmospheric pressure, as this introduces air and moisture. Allow the oil to enter slowly over 30-60 seconds to prevent foaming.
  5. 5
    Disconnect oil injector and secure port
    Remove the oil injector tool from the low-side service port. Immediately reinstall the service port cap to prevent moisture and contaminant entry. Wipe any spilled oil from surrounding components with clean rags.
  6. 6
    Evacuate and recharge AC system
    Connect vacuum pump to the AC manifold gauge set and evacuate the system for minimum 30 minutes to remove air and moisture. System should hold vacuum (29+ inHg) for at least 10 minutes. Recharge system with R-134a refrigerant to the exact capacity specified on the underhood A/C label or in Aston Martin service documentation for the 2009 DB9 (verify — do not rely on a generic estimate). Note: Recharge system with R-134a refrigerant to the exact specification listed on the underhood A/C label or in Aston Martin service documentation for the 2009 DB9 (capacity must be verified; do not rely on an estimated figure). Note: Recharge system with R-134a refrigerant to specification. Refer to the underhood A/C label or Aston Martin service documentation for the exact factory-specified refrigerant capacity before charging.
  7. 7
    Distribute oil through system
    Start engine and run AC system at maximum cooling and high blower speed for 10-15 minutes. This circulates the added oil throughout the system components. Monitor gauge pressures during operation: low side should be 25-35 psi, high side 200-250 psi at idle with ambient temperature 70-80°F.
  8. 8
    Inspect for leaks and verify operation
    With system running, inspect all AC line fittings, service ports, and compressor shaft seal for signs of oil leakage or refrigerant escape. Check that compressor clutch engages smoothly and AC output temperature at center vents is 40-50°F below ambient. Turn off engine and disconnect manifold gauge set.

Reassembly

  1. Ensure all service port caps are reinstalled securely
  2. Wipe down any PAG oil residue from engine bay components
  3. Store remaining PAG oil in sealed container away from moisture

Verification

  • AC system cools effectively with center vent temperatures 35-45°F at idle
  • No unusual noises from compressor during operation
  • Compressor clutch engages and disengages smoothly
  • No oil residue visible around compressor shaft seal or line fittings
  • System pressures remain stable: low side 25-40 psi, high side 200-275 psi (varies with ambient temperature)

Related trouble codes on this vehicle

Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.

Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →

🔧Stuck on this ac compressor oil add? Take it to The Diag Desk.A human with 20+ years in the bay answers about YOUR Aston Martin within 24 hours — never AI. $25, and you're not charged unless you get an answer.Ask a tech →

More procedures for this vehicle

For shop owners
Want more customers to find you?
We build shop websites with online booking onto your schedule and your own online store.
Talk to the ownerSee what's included
Built by a shop owner. Talk to Chris, not a sales rep.
🔧 Built by master technician Chris Hackleman · Master Technician · 20+ years. Spot an error? Use the Help link above — a human reads every report.
Stuck on this repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
⚠ STILL BEHIND THE PAYWALL
The 2009 Aston Martin DB9 repair data is incomplete because no one has sponsored it yet. For $99, we generate the full step-by-step procedures, then fact-check them with a second AI pass and your expert review. Your name on every procedure, permanently.
The same data would cost $169/mo from Mitchell1 or $30/year from ALLDATAdiy — and you'd be renting access, not freeing it. Sponsor once, free forever.
Sponsor the Aston Martin DB9 — $99 →
Building an app?
Free API key: 10 requests/day, 100/month, no card required.
Get an API key →
Run a shop?
A free website, SEO and Google reviews with your shop software. Auto Shop Base Professional, $250/mo, with our labor times on every estimate.
See what's included →