Free API
brakes

Brake Caliper Rebuild - Front

for 2009 Aston Martin DB9 6.0L V12 · RWD
Difficulty
Advanced
Time
2.3 h
Tools
15
Steps
15
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

Remove, disassemble, clean, inspect, and rebuild both front brake calipers with new seals and boots, then reinstall and bleed the brake system.

Warnings

⚠️BRAKE SYSTEM SAFETY: Errors in brake caliper rebuilding can result in complete brake failure, causing severe injury or death. If you are uncertain about any step, have the work performed by a qualified technician.
⚠️Never reuse old brake fluid. Contaminated or incorrect brake fluid will cause seal failure and brake malfunction.
⚠️Do not allow brake fluid contact with painted surfaces - it will permanently damage paint. Cover fenders and clean spills immediately with water.
⚠Compressed air for piston removal can eject pistons with dangerous force. Always use controlled pressure (20-30 PSI max) and keep fingers clear of piston path.
⚠Inspect all rubber components carefully. Any cracking, swelling, or degradation requires replacement of the entire seal kit.
⚠Brake fluid absorbs moisture and degrades over time. Use only fresh fluid from sealed containers.
ℹ️Work on one caliper at a time to maintain a reference assembly and prevent mixing parts between sides.
ℹ️Maintain absolute cleanliness throughout this procedure. Any contamination in the hydraulic system can cause brake failure.

Tools required

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Fluids

  • DOT 4 low-viscosity brake fluid — 1 qt
  • Brake assembly lubricant (silicone-based, rubber-safe)
  • Brake parts cleaner (non-chlorinated)

Preparation

  1. Park vehicle on level surface and ensure transmission is in Park with parking brake engaged (release parking brake after rear wheels are chocked).
  2. Chock rear wheels securely with wheel chocks on both sides.
  3. Locate brake fluid reservoir in engine bay and check fluid level. Mark or photograph current level for reference.
  4. Prepare clean workspace with all tools, parts, and fluids within reach. Ensure new caliper rebuild kits are correct for 2009 DB9 front calipers before beginning.
  5. Open fresh brake fluid container only when ready to use. Do not leave brake fluid exposed to air for extended periods.
  6. Review all torque specifications and have torque wrench calibrated and ready.

Procedure

  1. 1
    Raise vehicle and remove front wheels
    Loosen front wheel lug nuts one full turn while vehicle is on ground. Raise front of vehicle using floor jack at the designated factory front jacking point and support securely on jack stands at the Aston Martin-specified lift/support points (verify locations in the DB9 service manual before lifting). Remove front wheel lug nuts completely and remove both front wheels. Verify jack stands are stable before proceeding under vehicle. Note: support securely on jack stands positioned at the Aston Martin designated chassis lift/support points for the DB9
  2. 2
    Remove brake caliper from bracket
    Locate the brake hose banjo bolt connection at the caliper. Place drain container beneath caliper. Using a line wrench, loosen and remove the banjo bolt securing the brake hose to the caliper. Allow brake fluid to drain into container. Remove and discard the copper crush washers from the banjo connection (verify quantity and fitting type against the Aston Martin DB9 workshop manual). Cap or plug the brake hose immediately to prevent fluid loss and contamination. Remove the two caliper-to-upright mounting bolts that secure the fixed caliper to the hub carrier. Carefully lift the fixed caliper straight off the brake rotor. Repeat for second front caliper if working both sides simultaneously, otherwise complete one side fully before starting the other. Note: Remove the two caliper mounting bolts that secure the fixed caliper to the hub carrier/upright. Carefully lift caliper away from the brake rotor. Note: Remove the two caliper radial mounting bolts that secure the fixed caliper to the hub carrier.
    ⚠Brake fluid will drain immediately upon banjo bolt removal. Have drain container positioned before loosening bolt.
  3. 3
    Clean caliper exterior
    Place caliper on clean workbench surface. Using brake parts cleaner and shop towels, thoroughly clean all external surfaces of the caliper body, removing brake dust, road grime, and corrosion. Use wire brush on any corroded areas of the caliper housing (avoid brushing seal contact surfaces). Inspect caliper casting for cracks, especially around mounting ears and hydraulic passage areas. Any cracks require caliper replacement rather than rebuild.
  4. 4
    Remove caliper pistons
    Using compressed air method: Insert compressed air adapter into brake hose port on caliper. Place a folded shop towel over the piston opening to catch the piston. Apply compressed air gradually (start at low pressure, 20-30 PSI maximum) until piston ejects into the towel. Never place fingers in front of piston path. These are fixed opposed-piston calipers with multiple pistons on both sides (verify exact caliper type and piston count against Aston Martin DB9 factory service data before proceeding). When using compressed air, insert wooden blocks/spacers to retain pistons on one side while ejecting those on the other, then reverse the process; work carefully as all pistons will attempt to move simultaneously. Alternative method if compressed air unavailable: Use brake caliper piston removal tool per manufacturer instructions. Remove all pistons from caliper and set aside on clean surface. Note: This is a fixed opposed-piston caliper with pistons on both inboard and outboard sides. After the first piston is removed, insert a wooden block or spacer to retain the remaining pistons, managing opposing bores symmetrically, and repeat the process for all remaining pistons. Note: For opposed-piston calipers, pistons on both sides eject under air pressure. Use wooden blocks or C-clamp spacers to retain pistons you are not removing, and eject pistons individually in a controlled manner to prevent uneven ejection and jamming.
  5. 5
    Remove old seals and dust boots
    Using non-metallic seal pick or brass pick tool, carefully pry out the dust boot from its groove in the caliper bore. Remove and discard dust boot. Locate the piston seal seated in the groove inside the caliper bore. Using seal pick, gently work the seal out of its groove, taking care not to scratch or gouge the bore wall. Remove seal completely and discard. Repeat for all piston bores on both the inboard and outboard sides of the caliper.
    ⚠Use only non-metallic or brass tools to remove seals. Metal tools can scratch the bore surface, causing permanent damage and seal leaks.
  6. 6
    Clean and inspect caliper bores
    Spray all caliper bores thoroughly with brake parts cleaner. Using clean shop towels, wipe out all residue, old fluid, and contamination from bores. Inspect each bore carefully for scoring, pitting, corrosion, or scratches. Light surface corrosion may be carefully removed using fine emery cloth (400-600 grit) with a circular motion - never lengthwise. Deep scoring or pitting requires caliper replacement. Clean seal grooves thoroughly, ensuring no old seal material or debris remains. Inspect bleeder screw threads and valve seat for damage. Clean all hydraulic passages with brake parts cleaner.
  7. 7
    Inspect and measure pistons
    Clean old pistons thoroughly with brake parts cleaner. Inspect piston outer surface for scoring, corrosion, pitting, or wear. Measure piston outer diameter at multiple points using micrometer or digital caliper. Compare measurements to service specifications. Compare measurements to the Aston Martin DB9 service specification for acceptable piston wear (verify exact tolerance in factory service data). Check piston for straightness by rolling on flat surface - any wobble indicates replacement required. If pistons show any damage or excessive wear, use new pistons from rebuild kit. If reusing original pistons, ensure they are perfectly clean and undamaged.
  8. 8
    Install new piston seals
    Open new caliper rebuild kit and verify all components are present and correct for your application. Coat new piston seals lightly with fresh DOT 4 brake fluid. Carefully install each seal into its groove in the caliper bore, working the seal in with clean fingers. Ensure seal is fully seated in groove around entire circumference with no twists or kinks. Verify seal sits below the bore surface and is not pinched or rolled. Repeat for all piston bores.
    ⚠Use only fresh brake fluid as lubricant for seal installation. Never use petroleum-based lubricants which will destroy rubber seals.
  9. 9
    Install pistons and dust boots
    Coat piston outer surface lightly with fresh DOT 4 brake fluid. If using new pistons from rebuild kit, ensure any protective coatings are removed per kit instructions. Align piston squarely with caliper bore opening. Using hand pressure or piston installation tool, carefully push piston into bore, ensuring it enters straight without cocking. Push piston approximately halfway into bore. Install new dust boot into the groove on the piston, then seat the outer lip of the dust boot into its groove in the caliper body. Push piston fully into bore until it bottoms gently - do not force. Verify dust boot is properly seated in both grooves. Repeat for all pistons.
  10. 10
    Install slide pin boots and lubricate
    This vehicle uses a fixed opposed-piston caliper with no slide pins. Skip this step; verify instead that the two caliper-to-upright mounting bolt threads and bolts are clean and undamaged, and that the caliper mating faces on the upright are clean. Note: This step does not apply to the 2009 DB9, which uses fixed opposed-piston calipers without slide pins. Skip this step; there are no slide pins or slide pin boots to service. Note: This step does not apply to the 2009 DB9 front calipers, which are fixed opposed-piston (Brembo) units with no slide pins or floating bracket. Skip this step and proceed directly to caliper installation.
  11. 11
    Install caliper onto bracket
    Position the rebuilt caliper over the brake rotor and align with the mounting bolt holes in the hub carrier/upright. Install the brake pads into the caliper and secure with the pad retaining pins and anti-rattle clip. Apply a small amount of medium-strength threadlocker to the caliper mounting bolt threads. Install the caliper mounting bolts and hand-tighten, then torque to specification. Install new copper crush washers on both sides of brake hose banjo fitting. Connect brake hose to caliper and hand-start banjo bolt. Torque banjo bolt to the Aston Martin OEM specification (verify exact value in factory service data before tightening). Note: Verify brake pads are properly positioned in the caliper body (reinstall pads and retaining pins/clips at this time if removed). Position rebuilt caliper over the brake rotor and align with the mounting bolt holes in the hub carrier/upright. Apply a small amount of medium-strength threadlocker to the caliper mounting bolt threads. Install caliper mounting bolts and hand-tighten. Using a torque wrench, torque the caliper mounting bolts to specification. Note: Torque banjo bolt per Aston Martin workshop manual specification (verify exact value before assembly; do not rely on a generic estimate). Note: Torque the banjo bolt to the Aston Martin service-manual specification (verify exact value before assembly — do not rely on a generic estimate). Note: Position rebuilt caliper over the brake rotor and align with the radial mounting bolt holes in the hub carrier. Apply a small amount of medium-strength threadlocker to the mounting bolt threads. Install the two radial mounting bolts and hand-tighten. Using a torque wrench, torque the mounting bolts to Aston Martin specification. Note: Caliper-to-Upright Mounting Bolts
    Torque spec
    Caliper Slide Pin Bolts35 Nm (26 lb-ft)
  12. 12
    Bleed brake caliper
    Fill brake fluid reservoir to MAX line with fresh DOT 4 low-viscosity brake fluid. Locate bleeder screw on caliper body. Place clear tube over bleeder screw and submerge other end in brake fluid catch container. If using vacuum bleeder, attach vacuum pump to bleeder tube and open bleeder screw 1/2 turn. Apply vacuum until fluid flows with no air bubbles (approximately 30-60 seconds), then close bleeder screw. If manual bleeding, have assistant pump brake pedal 5-6 times and hold. Open bleeder screw 1/2 turn, allow fluid and air to escape, then close bleeder before pedal reaches floor. Repeat until fluid flows with no air bubbles. Verify firm pedal feel before proceeding. Check and top off reservoir frequently during bleeding process.
    ⚠️Never allow brake fluid reservoir to run empty during bleeding. Air entering the master cylinder or ABS unit may require professional scan tool bleeding.
    Torque spec
    Bleeder Screw10 Nm (7 lb-ft)
  13. 13
    Repeat for second caliper
    If working one caliper at a time (recommended), repeat steps 2 through 12 for the second front caliper. Maintain absolute cleanliness and use fresh brake fluid. After both calipers are rebuilt and installed, perform final system bleeding in the sequence specified by the Aston Martin workshop manual. Confirm the correct caliper bleed order for this vehicle before proceeding; for front-only work, bleed the front calipers per the manufacturer-specified order. Note: perform final system bleeding in the sequence specified by Aston Martin service data for the DB9 ABS/hydraulic system; verify whether scan-tool-assisted bleeding is required before relying on a manual sequence
  14. 14
    Reinstall wheels and perform final checks
    Verify all bleeder screws are closed and torqued properly. Check all brake line connections for leaks - wipe dry and inspect for seepage. Ensure no tools or parts remain in wheel well area. Install front wheels onto hubs. Install lug nuts and hand-tighten in star pattern. Lower vehicle until wheels just contact ground. Torque lug nuts to specification in star pattern. Lower vehicle completely and remove jack stands. Perform final lug nut torque verification in star pattern.
    Torque spec
    Bleeder Screw10 Nm (7 lb-ft)
    Wheel Lug Nuts89 Nm (66 lb-ft)
  15. 15
    Bed-in brake system and final verification
    Check brake fluid reservoir and top off to MAX line with fresh DOT 4 fluid. Pump brake pedal multiple times - pedal should be firm and consistent before starting engine. Start engine and verify pedal remains firm with power assist active. With engine running, inspect all caliper connections and brake hoses for leaks. Before moving vehicle, perform stationary brake application test. Test drive in safe area at low speed (under 15 mph), verifying smooth brake operation with no pulling, vibration, or unusual noises. Perform 5-10 moderate stops from 30 mph to begin pad seating process. Avoid hard stops for first 50-100 miles to allow proper pad bedding.
    ⚠️Braking performance will be reduced until pads are properly bedded. Avoid hard braking and maintain increased following distance for first 100 miles.

Reassembly

  1. Torque all fasteners to specification in the order presented: caliper slide pin bolts, bleeder screws, and wheel lug nuts in star pattern.
  2. Use only new copper crush washers on brake hose banjo connections - never reuse old washers.
  3. Apply medium-strength threadlocker to caliper bracket bolts as specified.
  4. Verify brake pedal is firm before test driving vehicle.
  5. Check brake fluid level after completion and top off as needed with DOT 4 low-viscosity brake fluid.

Verification

  • Brake pedal should be firm and high with engine off, and remain firm with good feel when engine is running (power assist active).
  • No brake fluid leaks visible at any caliper connection, bleeder screw, or brake hose junction.
  • Test drive reveals smooth, even braking with no pulling to either side, no vibration, and no unusual noises.
  • Both front wheels should show even heating after moderate braking - significant temperature difference indicates dragging caliper.
  • Brake fluid reservoir is at MAX line and fluid is clear (not dark or contaminated).
  • All pistons retract properly when brake pedal is released - verify by checking that wheels spin freely by hand with no drag.

Related trouble codes on this vehicle

Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.

Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →

🔧Stuck on this brake caliper rebuild - front? Take it to The Diag Desk.A human with 20+ years in the bay answers about YOUR Aston Martin within 24 hours — never AI. $25, and you're not charged unless you get an answer.Ask a tech →

More procedures for this vehicle

For shop owners
Want more customers to find you?
We build shop websites with online booking onto your schedule and your own online store.
Talk to the ownerSee what's included
Built by a shop owner. Talk to Chris, not a sales rep.
🔧 Built by master technician Chris Hackleman · Master Technician · 20+ years. Spot an error? Use the Help link above — a human reads every report.
Stuck on this repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
⚠ STILL BEHIND THE PAYWALL
The 2009 Aston Martin DB9 repair data is incomplete because no one has sponsored it yet. For $99, we generate the full step-by-step procedures, then fact-check them with a second AI pass and your expert review. Your name on every procedure, permanently.
The same data would cost $169/mo from Mitchell1 or $30/year from ALLDATAdiy — and you'd be renting access, not freeing it. Sponsor once, free forever.
Sponsor the Aston Martin DB9 — $99 →
Building an app?
Free API key: 10 requests/day, 100/month, no card required.
Get an API key →
Run a shop?
A free website, SEO and Google reviews with your shop software. Auto Shop Base Professional, $250/mo, with our labor times on every estimate.
See what's included →