maintenance
Cooling System Pressure Test
for 2009 Aston Martin DB9 6.0L V12 · RWD
Difficulty
Easy
Time
1.1 h
Tools
6
Steps
11
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.
Perform a pressure test on the cooling system to identify leaks in the radiator, hoses, water pump, heater core, or head gaskets on the 2009 Aston Martin DB9 6.0L V12.
Warnings
⚠️Never open the cooling system or perform pressure testing when the engine is hot. Pressurized coolant can cause severe burns. Allow the engine to cool completely for at least 2 hours before beginning work.
⚠Do not exceed the pressure rating stamped on the radiator cap during testing. Over-pressurizing can damage cooling system components including the radiator, hoses, and gaskets.
⚠The V12 engine has coolant passages on both cylinder banks. Inspect both sides of the engine bay thoroughly during pressure testing.
ℹ️Keep coolant away from painted surfaces and rinse immediately with water if contact occurs.
Tools required
Work light or inspection lampEssential
As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.
Parts
- Coolant (if draining is required for repairs) × 1 — Use OEM specification
As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.
Fluids
- coolant
Preparation
- Park vehicle on level ground and apply parking brake
- Ensure engine is completely cold to the touch (at least 2 hours after last operation)
- Open hood and secure with prop rod
- Locate the radiator cap on the coolant expansion tank, positioned on the right side of the engine bay
- Verify coolant level is at or near the COLD MAX mark on the expansion tank; top off with OAT 50/50 coolant if low before testing
- Place clean rags or a drip tray under the expansion tank area to catch any coolant spillage
Procedure
- 1Remove radiator cap and inspect cooling systemSlowly rotate the expansion tank pressure cap counterclockwise to release any residual pressure, then remove it completely. Visually inspect the cap for damaged seals, cracks, or corrosion on the sealing surfaces. Check the coolant condition in the expansion tank for contamination, oil presence, or rust particles. Note the coolant level before testing begins.
- 2Perform initial visual inspectionWith the system open, use a work light to inspect all visible coolant hoses, clamps, radiator, water pump area, and heater hoses for obvious signs of leakage, wetness, staining, or damage. Pay particular attention to hose connections at the thermostat housings on both cylinder banks, the water pump crossover pipe at the front of the engine, and connections at the radiator. Document any areas showing signs of previous or active leaks.
- 3Install pressure tester adapterSelect the appropriate adapter from the pressure tester kit that fits the expansion tank filler neck. The DB9 typically requires a universal tapered rubber adapter or a lever-lock style adapter. Thread or lock the adapter securely onto the expansion tank opening, ensuring a proper seal. Attach the pressure tester gauge and pump assembly to the adapter.
- 4Pressurize the cooling systemCheck the pressure rating stamped on the expansion tank pressure cap and verify the exact value against Aston Martin factory documentation before testing (do not assume a generic value). Slowly pump the pressure tester to bring the system pressure to the cap's OEM-rated pressure value. Do not exceed this rating. Observe the pressure gauge; a properly sealed system should hold pressure steadily without dropping. Note: Confirm the cap's rated pressure against factory service data. Slowly pump the pressure tester to bring the system pressure to the cap's rated pressure value.ion tank cap. Slowly pump the pressure tester to bring the system pressure to the cap's rated pressure value.
- 5Monitor pressure stabilityWatch the pressure gauge for 2-3 minutes without adding additional pressure. A healthy system will maintain pressure with minimal drop (less than 2 psi over 2 minutes is acceptable due to thermal changes). If pressure drops rapidly (more than 3-4 psi per minute), a leak is present and must be located. Record the pressure drop rate.
- 6Inspect external components under pressureWhile the system is pressurized, systematically inspect all cooling system components. Begin at the radiator, checking all seams, end tanks, and core for seepage. Inspect both upper and lower radiator hoses at connection points and along their length. Examine the water pump weep hole (consult factory documentation for its exact location on the AM V12 pump housing) for coolant discharge indicating seal failure. Check all heater hoses running to the firewall, thermostat housing connections on both banks, and any auxiliary coolant lines.
- 7Inspect cylinder head and block interfacesWith the system still under pressure, use the work light and inspection mirror to examine the cylinder head-to-block mating surfaces on both banks of the V12. Look for coolant weeping along the head gasket areas, particularly near the exhaust side where temperatures are highest. Check for coolant weeping near the head gasket seam and external coolant passages, which would indicate head gasket or seal failure. Inspect the valley area between the cylinder banks if accessible for coolant accumulation.
- 8Check interior heater coreWhile maintaining system pressure, check the passenger compartment carpet on both the driver and passenger sides for wetness, particularly under the dashboard area. Inspect for coolant odor inside the cabin. Run your hand along the carpet at the firewall and center tunnel area. A failed heater core will show dampness on the carpet or visible coolant dripping from the heater box drain. Look for fogging on the inside of windows which can indicate heater core seepage.
- 9Inspect coolant crossover pipes and connectionsThe DB9 V12 routes coolant between cylinder banks via engine coolant piping. With the system pressurized, inspect all accessible coolant transfer pipes and their connections for leaks at gasket interfaces, seams, O-rings, and threaded fittings. Consult factory documentation to confirm the exact routing and known leak points for this engine.hese areas are common leak points on the AM V12 engine. Note: Inspect the coolant distribution/crossover plumbing per OEM documentation; the AM 6.0L V12 routes coolant between banks via metal pipes and hoses whose exact layout should be confirmed against the factory service manual. Note: Inspect the metal coolant transfer/crossover pipes and connections for leaks at gasket interfaces, hose joints, and seams. Check all O-ring sealed and clamped connections for seepage. Verify the exact crossover pipe routing against Aston Martin service documentation for this engine.
- 10Test pressure cap functionRelease pressure from the system by carefully loosening the pressure tester connection. Remove the tester and adapter. Install the original expansion tank pressure cap onto the pressure tester adapter (if your tester has cap testing capability) and pump to test the cap's pressure relief function. The cap should hold pressure up to its rated value, then release. A cap that releases early or fails to seal indicates replacement is needed.
- 11Document findings and release pressureRecord all leak locations, pressure drop rates, and component conditions found during testing. If no leaks were found and the system held pressure within acceptable limits, the cooling system is sealed properly. Remove the pressure tester and adapter from the expansion tank. Reinstall the expansion tank pressure cap by aligning the tabs and rotating clockwise until it stops and locks into place.
Reassembly
- If testing revealed leaks requiring component removal, repair those components following appropriate procedures before refilling the system
- Ensure the radiator cap is properly seated and locked into position
- If coolant was lost during testing, top off the expansion tank to the COLD MAX mark with OAT 50/50 coolant
- Wipe any spilled coolant from the engine bay and painted surfaces
Verification
- With the radiator cap installed, start the engine and allow it to reach normal operating temperature while monitoring for leaks at any previously identified areas
- Check that the coolant level remains stable in the expansion tank after the engine reaches operating temperature
- Verify no coolant odor is present in the cabin and no warning lights illuminate on the dashboard
- After a test drive, recheck all cooling system components for signs of fresh leakage
- Confirm the expansion tank coolant level is between MIN and MAX marks when cold after the test drive
Related trouble codes on this vehicle
Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.
P0087Fuel Rail/System Pressure - Too LowP0088Fuel Rail/System Pressure - Too HighP0090Fuel Pressure Regulator 1 Control CircuitP0091Fuel Pressure Regulator 1 Control Circuit LowP0105Manifold Absolute Pressure/BARO CircuitP0106MAP/BARO Pressure Circuit Range/PerformanceP0129Barometric Pressure Too LowP0190Fuel Rail Pressure Sensor CircuitP0191Fuel Rail Pressure Sensor Circuit Range/PerformanceP0450Evaporative Emission System Pressure Sensor/Switch MalfunctionP0451Evaporative Emission System Pressure Sensor/Switch Range/PerformanceP0470Exhaust Pressure Sensor Malfunction
Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →