engine
Intake Manifold
for 2009 Aston Martin DB9 6.0L V12 · RWD
Difficulty
Expert
Time
7.6 h
Tools
13
Steps
20
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.
Removal and replacement of the intake manifold on the 2009 Aston Martin DB9 6.0L V12, including throttle body, fuel rail, and associated components.
Warnings
⚠️Fuel system operates under high pressure. Failure to relieve fuel pressure before disconnecting lines can cause fuel spray and fire risk.
⚠️Perform this work only when engine is completely cold. Hot coolant under pressure can cause severe burns.
⚠The V12 intake manifold is a large, heavy aluminum casting. Have an assistant available during removal and installation to prevent dropping and injury.
⚠Mark all vacuum lines, electrical connectors, and hose routing with labels before disconnection. The V12 has numerous connections that must be restored exactly.
ℹ️Use only OEM or approved equivalent gaskets. Aftermarket gaskets may not seal properly on this high-performance engine.
ℹ️Inspect all removed fasteners for thread damage or stretching. Replace any questionable hardware.
Tools required
Torque wrench (5-25 Nm range)Essential
Torx socket set (T20-T50)Essential
Fuel line disconnect tool setEssential
Fuel pressure gaugeEssential
Ratchet and extension setEssential
Clean lint-free ragsEssential
Socket set (8-19mm)Essential
Wire labels or masking tapeEssential
As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.
Parts
- Intake manifold gasket set × 1 — Use OEM Aston Martin specification
- Throttle body gasket × 1 — Use OEM specification
- Fuel rail O-rings and seals × 1 — Use OEM specification
- PCV valve grommet (if damaged) × 1 — Use OEM specification
- Coolant hose clamps (as needed) × 4 — Use OEM specification
- Vacuum line assortment (if damaged) × 1 — Use OEM specification
As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.
Fluids
- OAT 50/50 coolant — 2 qt
Preparation
- Ensure engine is completely cold (at least 4 hours after last operation).
- Disconnect negative battery cable and wait 10 minutes for system capacitors to discharge.
- Remove engine cover by lifting upward - it is retained by rubber grommets on ball studs.
- Place vehicle on level ground with parking brake applied.
- Photograph engine bay from multiple angles for reference during reassembly.
- Label all electrical connectors and vacuum lines as you encounter them with numbered tape corresponding to photos.
Procedure
- 1Relieve Fuel System PressureRelieve fuel pressure using the manufacturer-specified procedure for the 2009 DB9 V12 (e.g., removing the fuel pump fuse/relay and running the engine until it stalls, or via a Schrader test port if equipped). Verify the correct depressurization method in the service manual. Have absorbent rags ready for residual fuel spillage during line disconnection. Verify pressure drops to zero on the gauge. Remove gauge and cap the Schrader valve. Have absorbent rags ready for residual fuel spillage during line disconnection. Note: Relieve fuel pressure per the Aston Martin service procedure for this vehicle. If a fuel rail Schrader/test valve is fitted, attach a fuel pressure gauge and bleed pressure into a suitable container; otherwise use the manufacturer-specified pressure relief method (fuel pump fuse removal and cranking). Note: Determine the correct fuel depressurization method for this vehicle per factory service data. If equipped with a fuel rail Schrader valve, attach a fuel pressure gauge to bleed pressure; otherwise follow the manufacturer-specified depressurization procedure.
- 2Drain Coolant and Disconnect HosesPlace drain pan under lower radiator hose. Open radiator drain valve or carefully disconnect lower hose to drain sufficient coolant to drop the level below the intake manifold (verify required quantity against the Aston Martin service manual). Disconnect coolant hoses from the throttle body (verify exact count and routing against the Aston Martin service manual for this vehicle). Disconnect heater hoses if they attach directly to intake manifold. Use hose clamp pliers or appropriate tool for spring-type clamps. Note: drain enough coolant to drop the level below the intake manifold (verify the required quantity against official Aston Martin service data). Disconnect coolant hoses from throttle body - verify the exact number and location of throttle body coolant hoses against official Aston Martin service data.
- 3Remove Air Intake SystemLoosen clamps on intake air ducts leading to throttle body. Disconnect mass airflow sensor electrical connector. Remove air filter housing bolts (typically Torx fasteners) and lift housing assembly away. Remove intake air ducts from throttle body to airbox. On the V12, you may need to remove cross-brace or strut tower brace for access - these typically use 4-6 Torx bolts.
- 4Disconnect Throttle BodyDisconnect throttle position sensor and any other electrical connectors from throttle body. Remove the throttle body mounting bolts (verify exact count against the Aston Martin service manual). Carefully pull throttle body away from intake manifold. Inspect gasket and set throttle body aside on clean surface. Cover intake manifold opening with clean rag to prevent debris entry.Torque specThrottle Body Bolts10 Nm (7 lb-ft)
- 5Disconnect Fuel SystemDisconnect fuel supply and return lines from fuel rails using appropriate fuel line disconnect tools. Disconnect the fuel lines using the manufacturer-specified method and tool (verify fitting type — quick-disconnect, clip, or threaded — against the Aston Martin service manual). Have rags ready to catch residual fuel. Disconnect fuel injector electrical connectors - the V12 has one connector per injector (verify exact count and connector type against the Aston Martin service manual). Label each connector with cylinder number for reinstallation. Label each connector with cylinder number for reinstallation.
- 6Remove Fuel RailsRemove the fuel rail mounting bolts securing both rails (verify exact count against the Aston Martin service manual). Carefully lift fuel rails with injectors still attached as an assembly. Rock gently if injectors stick in manifold bores, but do not pry. Once free, place fuel rail assembly on clean shop towels away from work area. Cover exposed injector ports in intake manifold with clean rags or tape to prevent contamination. Note: Remove fuel rail mounting bolts - verify the exact count securing both rails against official Aston Martin service data.Torque specFuel Rail Bolts10 Nm (7 lb-ft)
- 7Disconnect Vacuum Lines and SensorsSystematically disconnect all vacuum lines from intake manifold, including brake booster vacuum line (large diameter hose at rear of manifold), PCV system hoses, purge valve lines, and any emissions control vacuum lines. Disconnect MAP sensor or manifold absolute pressure sensor electrical connector if mounted on manifold. Disconnect any coolant temperature sensors threaded into manifold. On the V12, expect multiple vacuum connections (verify exact count and locations against the Aston Martin service manual).
- 8Remove PCV Valve and ComponentsRemove PCV valve from valve cover or intake manifold (location varies by bank). The PCV system on the DB9 V12 includes crankcase ventilation hoses connecting both valve covers to the intake. Disconnect these hoses at manifold. Inspect PCV valve and grommet for damage - replace if deteriorated.Torque specPCV Valve8 Nm (6 lb-ft)
- 9Disconnect Wiring Harness BracketsRemove any wiring harness brackets or clips attached to intake manifold. The V12 has several harness routing brackets that bolt to the manifold - remove these fasteners (typically Torx bolts) and carefully move harnesses aside. Support harnesses with zip-ties or wire to prevent strain on connectors.
- 10Remove Intake Manifold FastenersLocate all intake manifold mounting bolts - the V12 intake manifold uses a specific number of mounting bolts around the perimeter and valley (verify exact count and pattern against the Aston Martin service manual). Remove bolts in reverse of tightening sequence (working from outer bolts toward center). Keep bolts organized by location as lengths may vary. Note any brackets or grounds that share bolt locations. Note: verify the exact count and location of intake manifold mounting bolts against official Aston Martin service data before removal.
- 11Remove Intake ManifoldWith all fasteners removed, carefully lift intake manifold straight up. The manifold is heavy and awkward - have an assistant support one end while you lift the other. Rock gently side-to-side if gasket adhesion causes resistance, but do not pry against sealing surfaces. Once free, lift manifold clear of engine and place on padded work surface. Immediately cover all cylinder head ports with clean rags or plastic sheeting to prevent debris or tools from falling into engine.
- 12Clean Gasket SurfacesCarefully remove all old gasket material from cylinder head mating surfaces and intake manifold mating surfaces. Use plastic scrapers only - never metal scrapers that could gouge aluminum surfaces. Clean surfaces with brake cleaner or appropriate solvent and lint-free rags. Inspect surfaces for warpage, cracks, or damage. Use vacuum to remove all debris from engine valley before installing new manifold. Ensure no gasket fragments fall into cylinder head ports or oil drain-back passages.
- 13Install New Gaskets and Position ManifoldInstall new intake manifold gaskets on cylinder heads. Most OEM gaskets are self-locating with alignment pins or molded positioning features. Verify gaskets are correctly oriented - they are not interchangeable left-to-right. Apply small dab of RTV sealant at front and rear corner joints where end seals meet side gaskets if specified in service manual (not all applications require this). With assistant's help, carefully lower intake manifold onto gaskets, ensuring all ports align and gaskets remain in position. Avoid sliding manifold once in contact with gaskets.Torque specIntake Manifold Bolt10 Nm (7 lb-ft)
- 14Install and Torque Manifold BoltsInstall all intake manifold bolts finger-tight, ensuring any brackets or grounds are positioned correctly under bolt heads. Torque bolts to specification following the exact tightening sequence specified in the Aston Martin service manual using torque wrench. Perform the torque sequence in multiple passes following the exact sequence diagram and intermediate/final torque values specified in the Aston Martin service manual (do not use assumed values or a generic center-outward pattern). Verify the actual multi-stage torque values and final specification from the 2009 DB9 6.0L V12 service manual before final tightening. This ensures even gasket compression and prevents warpage. Verify all bolts reach specification without excessive effort (which could indicate cross-threading). Note: Perform the torque sequence in multiple passes per the Aston Martin service manual, tightening to the specified intermediate and final torque values in the specified order (do not use assumed values). Note: Perform torque sequence in multiple passes per the factory service manual, typically a snug initial pass followed by a final pass to the specified torque. Verify the exact intake manifold bolt torque specification against official Aston Martin service data before final tightening. Note: Torque bolts to specification following the factory-specified tightening sequence using a torque wrench. Verify the exact bolt sequence diagram against official Aston Martin service data.Torque specIntake Manifold Bolt10 Nm (7 lb-ft)
- 15Reinstall PCV System and Vacuum LinesReinstall PCV valve with new grommet if needed, torquing to specification. Reconnect all crankcase ventilation hoses to intake manifold. Systematically reconnect all vacuum lines using labels and photos as reference. Ensure each connection is fully seated and secure. Replace any deteriorated vacuum lines. Reconnect brake booster vacuum line ensuring clamp is tight.Torque specPCV Valve8 Nm (6 lb-ft)
- 16Reinstall Fuel Rails and InjectorsLubricate fuel injector O-rings with clean engine oil or the OEM-specified assembly lubricant (do not use gasoline). Carefully position fuel rail assembly over injector ports, ensuring all 12 injectors align with their bores. Press down firmly and evenly on fuel rail until all injectors seat fully in manifold. Install fuel rail mounting bolts and torque to specification, following the tightening sequence specified in the Aston Martin service manual. Reconnect all 12 fuel injector electrical connectors in correct cylinder order using labels.Torque specFuel Rail Bolts10 Nm (7 lb-ft)
- 17Reinstall Throttle Body and Air IntakeInstall new throttle body gasket on intake manifold. Position throttle body and install mounting bolts, torquing to specification in cross-pattern. Reconnect throttle position sensor and other electrical connectors. Reinstall intake air ducts and air filter housing. Reconnect mass airflow sensor. Reinstall any strut braces or cross-braces removed earlier. Ensure all clamps are tight and air intake system is sealed.Torque specThrottle Body Bolts10 Nm (7 lb-ft)
- 18Reconnect Fuel Lines and Coolant SystemReconnect fuel supply and return lines to fuel rails, ensuring quick-disconnect fittings click into place securely. Tug gently to verify locking engagement. Reconnect coolant hoses to throttle body and intake manifold using new clamps if originals are damaged. Reconnect heater hoses if removed.
- 19Reconnect Sensors and HarnessesReinstall all wiring harness brackets and clips to intake manifold using original fasteners. Reconnect any temperature sensors or MAP sensors to intake manifold, torquing sensors to the specification listed in the 2009 DB9 6.0L V12 service manual. Route harnesses in original positions to avoid heat sources or pinch points. Note: torquing sensors to the specification given in the Aston Martin service manual Note: Reconnect any temperature sensors or MAP sensors to intake manifold, torquing sensors to the manufacturer-specified value. Verify the exact sensor torque specification against official Aston Martin service data before final tightening.
- 20Refill Coolant and Final ChecksRefill the cooling system with the Aston Martin-specified coolant at the correct mix ratio through the radiator or expansion tank, using the full quantity required (reconcile with the amount drained in step 2). Fill until level reaches proper mark. Reconnect negative battery cable. Before starting engine, perform visual inspection of all connections, verifying no tools or rags were left in engine bay. Check that all electrical connectors are seated and locked. Verify all vacuum lines are connected and fuel lines are secured. Note: Refill cooling system with the Aston Martin-specified coolant at the correct mix ratio through radiator or expansion tank, per the 2009 DB9 service manual. Note: Aston Martin-specified 50/50 coolant Note: Refill cooling system with the Aston Martin specified 50/50 coolant mixture through radiator or expansion tank. Verify the correct coolant specification against official Aston Martin service data.
Reassembly
- Reinstallation follows removal steps in reverse order.
- Always use new gaskets and O-rings - never reuse intake manifold gaskets or fuel injector seals.
- Torque all fasteners in proper sequence using multiple passes as specified.
- Reference photographs and labels made during disassembly to ensure correct routing of vacuum lines and harness placement.
Verification
- With engine still off, turn ignition to ON position (not start) and listen for fuel pump priming. Check for fuel leaks at all disconnected fuel line connections.
- Start engine and allow to idle. Monitor for smooth idle and any rough running that could indicate vacuum leaks or injector connection issues.
- Check for coolant leaks at all coolant hose connections while engine warms up.
- With engine at operating temperature, check for any vacuum leaks by listening for hissing sounds around intake manifold perimeter. Use propane enrichment method if necessary to locate leaks (propane will cause RPM increase at leak point).
- Verify no check engine light illumination. If present, scan for diagnostic trouble codes related to fuel trim, misfire, or sensor issues.
- Test drive vehicle to verify smooth acceleration, no hesitation, and proper throttle response across all RPM ranges.
- After test drive, recheck all connections for leaks and verify coolant level has not dropped (indicating leak or incomplete fill).
Related trouble codes on this vehicle
Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.
P0010Intake Camshaft Position Actuator Circuit/Open Bank 1P0011Intake Camshaft Position Timing Over-Advanced Bank 1P0020Intake Camshaft Position Actuator Circuit/Open Bank 2P0021Intake Camshaft Position Timing Over-Advanced Bank 2P0075Intake Valve Control Solenoid Circuit (Bank 1)P0076Intake Valve Control Solenoid Circuit Low (Bank 1)P0081Intake Valve Control Solenoid Circuit (Bank 2)P0082Intake Valve Control Solenoid Circuit Low (Bank 2)P0095Intake Air Temperature Sensor 2 CircuitP0096Intake Air Temperature Sensor 2 Circuit Range/PerformanceP0105Manifold Absolute Pressure/BARO CircuitP0110Intake Air Temperature (IAT) Sensor 1 Circuit
Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →