Sun Visor

This procedure covers removal and installation of the driver or passenger sun visor on a 2009 Aston Martin DB9, including disconnection of any integrated lighting or vanity mirror wiring.

Warnings

Tools required

Parts

• Sun visor assembly × 1 — Use OEM specification for driver or passenger side

Preparation

1. Ensure ignition is off and key is removed from vehicle
2. Open the sun visor fully to expose mounting hardware
3. If visor has integrated lighting or vanity mirror, verify connector access before removal

Procedure

1. 1

   Locate visor mounting fasteners
   The sun visor mounts to the headliner at the pivot bracket near the windshield edge. Visually inspect the pivot bracket cover for Torx fasteners. The DB9 pivot bracket is retained by mounting screws; verify the exact count and fastener type during inspection and against OEM documentation. If a secondary support clip is present near the B-pillar side, note its location. Note: The pivot bracket fastener type and size must be verified against Aston Martin factory documentation for the 2009 DB9 before removal; do not assume Torx type or size.
2. 2

   Remove pivot bracket cover (if equipped)
   Some visor designs have a small cosmetic cover over the pivot bracket. If present, gently pry the cover off using a trim tool, working from the rear edge. The cover typically clips in place without fasteners. Set aside for reinstallation.
3. 3

   Remove visor mounting screws
   Remove the mounting screws securing the visor pivot bracket to the headliner mounting plate using the appropriate Torx driver (verify size against OEM documentation). Support the visor with one hand while removing the final screw to prevent it from dropping. Retain screws for reinstallation. Support the visor with one hand while removing the final screw to prevent it from dropping. Retain screws for reinstallation. Note: Using the appropriate Torx driver, remove the mounting screws securing the visor pivot bracket to the headliner mounting plate. Verify the exact Torx size and screw count against OEM documentation for the 2009 DB9. Note: Using the appropriate Torx driver, remove the mounting screws securing the visor pivot bracket to the headliner mounting plate (verify Torx size and screw count against factory documentation for this vehicle).
   Torque spec

   Visor Mounting Screws3 Nm (2 lb-ft)
4. 4

   Disconnect electrical connector (if equipped)
   If the visor has an integrated vanity mirror light or other electrical feature, locate the wiring connector behind the pivot bracket. Press the release tab on the connector and gently pull the connector halves apart. Do not pull on the wires themselves. Route the connector through the headliner opening as you lower the visor.
5. 5

   Remove visor from vehicle
   With screws removed and wiring disconnected, carefully withdraw the visor assembly from the headliner. If a support clip is present on the opposite end (passenger side location where visor parks), slide the visor rod out of the clip receiver before complete removal.
6. 6

   Install new or replacement visor
   Position the new visor assembly at the mounting location. If a support clip is used, insert the visor rod into the clip receiver first to stabilize the assembly. Align the pivot bracket mounting holes with the headliner mounting plate.
7. 7

   Connect electrical connector (if equipped)
   Route the visor wiring connector through the headliner opening and mate it with the vehicle harness connector behind the pivot bracket. Ensure the connector locks with an audible click. Verify the connection is secure by gently tugging on the connector body (not wires).
8. 8

   Install visor mounting screws
   Insert the mounting screws through the pivot bracket and thread them into the headliner mounting plate by hand (verify screw count and Torx size against OEM documentation). Using a torque wrench, tighten the mounting screws to the manufacturer-specified torque (verify against OEM documentation). Do not overtighten, as the headliner mounting plate may be plastic or composite material. Do not overtighten, as the headliner mounting plate may be plastic or composite material. Note: Insert the mounting screws through the pivot bracket and thread them into the headliner mounting plate by hand. Snug each screw evenly to a low torque sufficient to seat the bracket without deforming the mounting plate; verify the exact torque specification against OEM documentation for the 2009 DB9. Note: Insert the mounting screws through the pivot bracket and thread them into the headliner mounting plate by hand. Using a torque wrench, tighten each screw to the factory-specified torque (verify value and Torx size against factory documentation) to ensure even clamping force.
   Torque spec

   Visor Mounting Screws3 Nm (2 lb-ft)
9. 9

   Reinstall pivot bracket cover (if equipped)
   If a cosmetic cover was removed in Step 2, align the cover clips with the pivot bracket receptacles and press firmly until the cover snaps into place. Ensure all edges are seated flush.
10. 10

    Test visor operation
    Rotate the visor through its full range of motion to verify smooth operation at the pivot. Swing the visor to the side window position and back to the windshield position. If equipped with vanity mirror lighting, turn the ignition to accessory position and open the vanity mirror cover to confirm the light illuminates. Check that the visor holds position without drooping.

Reassembly

1. Installation is performed in reverse order of removal
2. Ensure electrical connectors are fully seated before securing visor to headliner
3. Torque mounting screws to specification to prevent visor sag or looseness

Verification

• Visor rotates smoothly through full range of motion without binding or excessive resistance
• Visor holds position at windshield and side window locations without drooping
• Vanity mirror light (if equipped) illuminates when mirror cover is opened with ignition in accessory position
• No rattles or loose hardware when operating visor or driving vehicle
• Pivot bracket cover (if equipped) is flush and secure with no visible gaps

More procedures for this vehicle