Free API
electrical

Wiper Motor - Front

for 2009 Aston Martin DB9 6.0L V12 · RWD
Difficulty
Moderate
Time
2.5 h
Tools
7
Steps
15
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

Remove and replace the front windshield wiper motor assembly on a 2009 Aston Martin DB9, requiring removal of the cowl panel and wiper linkage.

Warnings

⚠Disconnect battery negative terminal and wait 2 minutes before beginning work to allow airbag system to discharge.
⚠Do not force wiper arms or linkage components, as the plastic bushings can crack easily.
ℹ️Mark wiper arm positions on the windshield before removal to ensure proper reassembly position.

Tools required

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Preparation

  1. Park vehicle on level surface and engage parking brake.
  2. Mark wiper blade resting positions on windshield with tape or marker for reference.
  3. Disconnect battery negative terminal.
  4. Wait at least 2 minutes for electrical system discharge.
  5. Open hood and secure in upright position.

Procedure

  1. 1
    Remove wiper arms
    Lift the plastic cap at the base of each wiper arm to expose the retaining nut. Remove the retaining nut from each wiper arm (verify socket size against the fastener before applying force). Gently rock the wiper arms while pulling away from the windshield to release them from the splined shaft. Remove both wiper arms completely. Note: Remove the retaining nut from each wiper arm (verify exact socket size against the 2009 DB9 workshop manual before applying force). Note: Remove the retaining nut from each wiper arm (verify socket size against OEM documentation; commonly 13mm or 14mm).
  2. 2
    Remove cowl panel weather seal
    Starting at one end, carefully pull the rubber weather seal from the cowl panel. The seal runs the full width of the cowl and simply pulls free from its retaining channel. Set aside for reinstallation.
  3. 3
    Remove cowl panel fasteners
    Locate and remove the Torx fasteners securing the cowl panel. Remove the cowl panel fasteners (exact count, Torx size, and locations to be confirmed against 2009 DB9 workshop manual) and retain them. Remove all fasteners and retain them. Note: The cowl panel is secured by a combination of fasteners and clips along the rear edge where it meets the bulkhead; verify exact fastener count and drive type against the Aston Martin DB9 workshop manual before removal. Note: Remove the cowl panel fasteners along the rear edge where it meets the bulkhead (exact count and Torx size must be verified against OEM documentation for the 2009 DB9).
  4. 4
    Release cowl panel clips and remove
    Using trim tools, carefully release the plastic clips securing the front edge of the cowl panel. Work from one side to the other, gently prying upward to disengage clips. Once all fasteners and clips are released, lift the cowl panel up and away from the vehicle. Inspect clips for damage and replace any broken clips.
  5. 5
    Disconnect wiper motor electrical connector
    Locate the wiper motor electrical connector on the passenger side of the wiper motor housing. Press the locking tab and disconnect the multi-pin connector from the wiper motor. Move the wiring harness aside to provide clearance.
  6. 6
    Disconnect wiper linkage from motor
    Locate the linkage arm connection point on the wiper motor output shaft. Remove the retaining clip or fastener securing the linkage ball joint to the motor crank arm. Carefully separate the linkage from the motor crank arm using a small pry tool if necessary. Note the orientation of components for reassembly.
  7. 7
    Remove wiper motor mounting bolts
    Remove the wiper motor mounting bolts (exact count and fastener type to be confirmed against 2009 DB9 workshop manual; note the motor may be attached to the linkage carrier frame rather than directly to the bulkhead). Support the motor as you remove the final bolt. Support the motor as you remove the final bolt to prevent it from dropping. Note: Remove the mounting bolts securing the wiper motor to the bulkhead/plenum chamber; verify exact count and fastener type against the Aston Martin DB9 workshop manual before removal. Note: Remove the mounting bolts securing the wiper motor to the bulkhead/plenum chamber (exact count and fastener type must be verified against OEM documentation for the 2009 DB9). Support the motor as you remove the final bolt to prevent it from dropping.
  8. 8
    Remove wiper motor assembly
    Carefully extract the wiper motor assembly from the plenum chamber. Maneuver the motor through the mounting aperture, being careful not to damage any surrounding components or the motor mounting grommet. Inspect the mounting grommet/seal for damage and replace if deteriorated.
  9. 9
    Prepare new wiper motor
    Remove the new wiper motor from packaging. Verify that the motor output shaft is in the park position (typically fully counterclockwise). Transfer any mounting hardware or grommets from the old motor if not included with the new unit. Clean the mounting surface on the bulkhead with contact cleaner or wire brush if corrosion is present.
  10. 10
    Install new wiper motor
    Position the new wiper motor into the plenum chamber mounting location. Ensure the mounting grommet is properly seated. Align the motor mounting holes with the bulkhead holes. Install the mounting bolts hand-tight initially, then torque to the Aston Martin specified value (to be confirmed against 2009 DB9 workshop manual) in a crossing pattern. Note: Install the mounting bolts hand-tight initially, then torque to the Aston Martin specification in a crossing pattern (verify exact torque value and bolt count against the DB9 workshop manual). Note: Install the mounting bolts hand-tight initially, then torque to the OEM-specified value in a crossing pattern (verify bolt count and torque spec against 2009 DB9 documentation).
    Torque spec
    Module Mounting Bolts8 Nm (6 lb-ft)
  11. 11
    Reconnect wiper linkage
    Align the wiper linkage ball joint with the motor crank arm. Press the ball joint onto the crank arm stud and install the retaining clip or fastener. Verify the connection is secure by gently tugging on the linkage. Ensure the linkage moves freely without binding.
  12. 12
    Reconnect electrical connector
    Reconnect the multi-pin electrical connector to the wiper motor. Ensure the connector locks into place with an audible click. Route the wiring harness away from moving linkage components.
  13. 13
    Reinstall cowl panel
    Position the cowl panel over the wiper mechanism area. Press down firmly on the front edge to engage the plastic retaining clips. Install all Torx fasteners along the rear edge, tightening in sequence from center outward. Do not overtighten plastic-mounted fasteners.
  14. 14
    Reinstall weather seal and wiper arms
    Press the rubber weather seal back into its retaining channel along the cowl panel, ensuring it is fully seated. Position each wiper arm onto its splined shaft according to your reference marks. Install the wiper arm retaining nuts and torque to the Aston Martin specification (verify socket size and torque value against the DB9 workshop manual). Press the plastic caps back over the nuts.
  15. 15
    Reconnect battery and test operation
    Reconnect the battery negative terminal and torque to the Aston Martin specified value (confirm against 2009 DB9 workshop manual). Turn the ignition to the ON position (engine off). Activate the wiper system through all speeds (intermittent, low, high) and verify smooth operation. Test the park function by turning the wipers off mid-cycle and confirming they return to the correct rest position. Check for any unusual noise or binding. Note: Reconnect the battery negative terminal and torque to the Aston Martin specification (verify value against the DB9 workshop manual). Note: Reconnect the battery negative terminal and torque to the OEM-specified value (verify against 2009 DB9 documentation).
    Torque spec
    Battery Terminal Bolts6 Nm (4 lb-ft)

Reassembly

  1. Ensure all cowl panel clips are fully engaged before tightening fasteners.
  2. Verify wiper arms are positioned correctly according to reference marks before tightening retaining nuts.
  3. Do not overtighten plastic-mounted fasteners to avoid cracking mounting points.

Verification

  • Test wiper operation at all speeds (intermittent, low, high) with engine running.
  • Verify wipers return to correct park position when turned off.
  • Check for proper wiper blade contact across entire windshield sweep.
  • Listen for unusual noises indicating binding or misalignment.
  • Spray washer fluid and verify wipers clear fluid properly.
  • Inspect cowl panel for proper seating and no gaps or rattles.

Related trouble codes on this vehicle

Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.

Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →

🔧Stuck on this wiper motor - front? Take it to The Diag Desk.A human with 20+ years in the bay answers about YOUR Aston Martin within 24 hours — never AI. $25, and you're not charged unless you get an answer.Ask a tech →

More procedures for this vehicle

For shop owners
Want more customers to find you?
We build shop websites with online booking onto your schedule and your own online store.
Talk to the ownerSee what's included
Built by a shop owner. Talk to Chris, not a sales rep.
🔧 Built by master technician Chris Hackleman · Master Technician · 20+ years. Spot an error? Use the Help link above — a human reads every report.
Stuck on this repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
⚠ STILL BEHIND THE PAYWALL
The 2009 Aston Martin DB9 repair data is incomplete because no one has sponsored it yet. For $99, we generate the full step-by-step procedures, then fact-check them with a second AI pass and your expert review. Your name on every procedure, permanently.
The same data would cost $169/mo from Mitchell1 or $30/year from ALLDATAdiy — and you'd be renting access, not freeing it. Sponsor once, free forever.
Sponsor the Aston Martin DB9 — $99 →
Building an app?
Free API key: 10 requests/day, 100/month, no card required.
Get an API key →
Run a shop?
A free website, SEO and Google reviews with your shop software. Auto Shop Base Professional, $250/mo, with our labor times on every estimate.
See what's included →