🌍 International coverage, work in progress. This Russian-market vehicle is part of our hand-curated international catalog. We are filling in labor times, torque specs and fluids as fast as we can verify them, so some numbers may be missing or marked estimated for now. Do you work on these vehicles in the EU, Russia, or the JDM scene? Help us get it right: send real shop times or corrections to [email protected], or request the data you need and it joins the verification queue.

2012 BMW 320I

2.0L I4 Turbo N20RWDAUTOMATICgasN20B20turbo
Be the first sponsor for this vehicle

For $99, we generate the full set of step-by-step repair procedures for this exact vehicle. Free for everyone, forever, with your name on every one.

Sponsor — $99
Dead battery / stuck in Park? Emergency neutral procedure for this 320i
Every control module on the 2011-2015 BMW 320i — where it lives, replacement time, and what it takes to program a replacement. Modules marked dealer / factory tool won't work after a part swap alone — budget for programming.
Electronic Transmission Control (EGS)2.8 hr R&Rdealer / factory tool +1.2 hr▸ programming details
📍 Transmission bell housing, driver side (automatic only)
🔧 BMW ISTA/P
⚠️ Transmission drop required. Adaptation and test drive mandatory. Flash programming dealer-only on F30.
Electric Power Steering (EPS)2.5 hr R&Rdealer / factory tool +0.8 hr▸ programming details
📍 Steering column, behind dash or on steering rack
🔧 BMW ISTA/P
⚠️ F30 uses electric power steering. Steering angle sensor calibration mandatory after replacement.
Integrated Heating Air Conditioning (IHKA)2.2 hr R&Raftermarket tool +0.4 hr▸ programming details
📍 Behind center dash, below radio unit
🔧 BMW ISTA/D or Autel MaxiSys
⚠️ Automatic climate control. Calibration typically auto-completes but may need ISTA/D.
Car Access System (CAS)1.8 hr R&Rdealer / factory tool +2.0 hr▸ programming details
📍 Steering column, behind lower dash trim driver side
🔧 BMW ISTA/P with dealer authentication
⚠️ All keys must be re-matched. DME ISN sync required. F30 CAS4+ has enhanced security; replacement nearly always dealer-only.
Navigation Business / Professional (NBT)1.8 hr R&Rdealer / factory tool +0.8 hr▸ programming details
📍 Behind center dash, accessible from glove box removal
🔧 BMW ISTA/P
⚠️ NBT (Next Big Thing) iDrive system. FSC codes VIN-locked. Coding required for feature activation.
Dynamic Stability Control (DSC)1.6 hr R&Rdealer / factory tool +0.6 hr▸ programming details
📍 Engine bay, driver side inner fender near brake master cylinder
🔧 BMW ISTA/P
⚠️ Brake bleeding required. Steering angle sensor and yaw sensor calibration mandatory.
Digital Motor Electronics (DME)1.3 hr R&Rdealer / factory tool +1.0 hr▸ programming details
📍 Engine bay, rear firewall driver side, under cowl panel
🔧 BMW ISTA/P with dealer authentication
⚠️ ISN synchronization with CAS mandatory. F30 has enhanced security; aftermarket programming very limited.
Central Gateway Module (ZGW)1.3 hr R&Rdealer / factory tool +1.0 hr▸ programming details
📍 Behind glove box, passenger footwell area
🔧 BMW ISTA/P
⚠️ F30 gateway has security protocols. Manages all CAN bus communication. Full vehicle configuration required.
Footwell Module / Front Electronic Module (FRM/FEM)1.2 hr R&Rdealer / factory tool +1.0 hr▸ programming details
📍 Driver footwell, behind kick panel above dead pedal
🔧 BMW ISTA/P
⚠️ F30 uses FEM (Front Electronic Module) architecture. Controls all body functions, lighting, comfort access. Critical security module.
Active Cruise Control Radar (ACC)1.2 hr R&Rdealer / factory tool +0.8 hr▸ programming details
📍 Front bumper, center behind grille (if equipped)
🔧 BMW ISTA/P
⚠️ Optional equipment. Radar calibration and alignment required after replacement. Dealer tool mandatory.
Door Module (TRSVC)1.0 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Inside each door (power/comfort access equipped vehicles)
🔧 BMW ISTA/D
⚠️ Controls window, mirror, comfort access antenna. Coding usually straightforward but may need ISTA/D.
Advanced Crash Safety Module (ACSM)0.9 hr R&Rdealer / factory tool +0.6 hr▸ programming details
📍 Center console, under center armrest or behind radio trim
🔧 BMW ISTA/P
⚠️ Battery disconnect mandatory. Wait 3+ minutes. Crash data clearing requires dealer tool.
Fuel Pump Control Module (EKPM)0.9 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Trunk, under trunk floor near fuel tank
🔧 BMW ISTA/D or Autel
⚠️ Controls fuel pump and pressure regulation. Usually auto-adapts but coding recommended.
Electronic Damper Control (EDC)0.9 hr R&Raftermarket tool +0.4 hr▸ programming details
📍 Trunk, right side near wheel well (adaptive suspension only)
🔧 BMW ISTA/D
⚠️ Only on vehicles with adaptive M Sport suspension. Calibration drive recommended.
Park Distance Control (PDC)0.8 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Trunk, left or right side trim panel (if equipped)
🔧 BMW ISTA/D or Autel
⚠️ Optional equipment. Sensor calibration may be required.
Telematics Communication Box (TCB)0.8 hr R&Rdealer / factory tool +0.5 hr▸ programming details
📍 Trunk, left or right side trim panel or under rear deck
🔧 BMW ISTA/P
⚠️ BMW Assist / ConnectedDrive module. Requires dealer activation and VIN coding.
Instrument Cluster (KOMBI)0.7 hr R&Rdealer / factory tool +0.6 hr▸ programming details
📍 Dashboard, behind instrument cluster trim
🔧 BMW ISTA/P with dealer authentication
⚠️ Mileage programming strictly dealer-only. VIN and FA coding mandatory.
Seat Module (SM)0.7 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Under driver or passenger seat (power/memory seats only)
🔧 BMW ISTA/D or Autel
⚠️ Only on vehicles with power memory seats. Memory positions may need relearning.
Adaptive Headlight Module (AHL)0.6 hr R&Raftermarket tool +0.4 hr▸ programming details
📍 Each headlight assembly (xenon/LED/adaptive models)
🔧 BMW ISTA/D or Autel
⚠️ F30 may have LED or xenon. Headlight aim calibration required. Some LED modules may need dealer coding.
Rear View Camera (RFK)0.5 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Trunk lid, integrated in handle or emblem (if equipped)
🔧 BMW ISTA/D or Autel
⚠️ Optional equipment. Camera calibration and coding for NBT integration required.
Aftermarket tool coverage varies by software version and vehicle build — treat "aftermarket tool" rows as "usually possible" and verify against your tool maker's coverage list before promising a customer. Spot a wrong location or hour? Tell us — corrections ship fast here.
🔧 Database maintained under the daily editorial review of Chris Hackleman · Master Technician · 20+ years.
Stuck on a repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
Building an app?
Free API access to all this data — 10 requests/day, no card required.
Get an API key →
Run a shop?
Manage repairs, estimates, and customers with ShopBase — $249/mo, all features included. Built by the same team.
Try ShopBase →