1997 CHRYSLER CONCORDE

Typical onset: 80,000-140,000 mi

Symptoms: Slipping between gears, especially 2nd-3rd shift, Delayed engagement into Drive or Reverse, Whining or grinding noise from bellhousing, Transmission overheating, burnt ATF smell, Complete loss of forward gears, limp mode

Fix: The 42LE four-speed automatic has weak overdrive clutches and inadequate cooling. Internal clutch pack failure requires full rebuild or replacement. External trans oil cooler often fails first, contaminating fluid and accelerating internal damage. Rebuild: 12-16 hours labor. Reman unit swap: 8-10 hours. Always replace cooler and flush lines during trans work.

Estimated cost: $2,200-3,800

Typical onset: 90,000-150,000 mi

Symptoms: Loud ticking or knocking from lower engine, worse when cold, Low oil pressure warning at idle, Metal shavings in oil during changes, Excessive oil consumption between changes, Catastrophic rod bearing failure, engine seizure

Fix: The 3.5L V6 develops sludge in the oil galleries if oil changes are extended beyond 5,000 mi, starving rod and main bearings. Once knocking starts, damage is done—requires short block replacement or full rebuild with new bearings, rings, and often head gaskets. 20-28 hours labor for short block swap. The 3.3L is significantly more tolerant of neglect.

Estimated cost: $3,500-5,500

Typical onset: 70,000-120,000 mi

Symptoms: Heavy clunk or thud when shifting from Park to Drive, Excessive engine movement visible under hood during acceleration, Vibration through steering wheel at idle in gear, Grinding or rubbing noise from engine bay during takeoff

Fix: Hydraulic front and rear transmission mounts collapse, allowing powertrain to rock violently and damage shift cables, exhaust hangers, and cooler lines. Replace all three mounts (front trans, rear trans, torque strut) as a set. 3-4 hours labor. Leaving this unrepaired often causes the transmission cooler lines to crack, leading to total fluid loss.

Estimated cost: $350-650

Typical onset: 100,000-160,000 mi

Symptoms: No-start condition, cranks but won't fire, Fuel gauge reading empty when tank is full, or stuck at half, Engine stalling at highway speed, especially in hot weather, Whining noise from rear seat area while driving

Fix: In-tank fuel pump and level sender corrode from ethanol fuel. Pump failure causes no-start; sender failure gives false gauge readings. Requires dropping the fuel tank to access pump module. 2.5-3.5 hours labor. Often the strainer sock is clogged with rust debris, so replace the entire pump assembly, not just the motor.

Estimated cost: $450-750

Typical onset: 80,000-130,000 mi

Symptoms: Coolant seeping from front of engine, pooling under intake plenum, Rough idle, stumbling, or misfires when cold, Coolant loss with no visible external leaks, White smoke from exhaust on cold start (if coolant enters cylinders)

Fix: Upper and lower intake manifold gaskets deteriorate, leaking coolant externally or into cylinders. Requires removing intake plenum, fuel rail, and throttle body. 4-6 hours labor. Use updated composite gaskets, not OEM paper. If coolant has been leaking into oil, expect bearing damage requiring teardown.

Estimated cost: $600-1,100

Typical onset: 90,000-140,000 mi

Symptoms: Clunking from front end over bumps or during slow turns, Excessive play in steering wheel, vague on-center feel, Grease weeping from inner tie rod boots, Popping noise when turning wheel lock-to-lock while stationary

Fix: Inner tie rod sockets wear out, requiring rack replacement or inner tie rod service if caught early. Boots tear, allowing contamination. If just boots and tie rods, 2-3 hours labor per side. If rack is worn internally (common), full rack replacement: 4-5 hours. Alignment required after any tie rod work.

Estimated cost: $400-900

Symptoms: Blower fan only works on high speed setting, No blower operation at all, even on high, Intermittent blower function, cuts out over bumps, Burning smell from under dash near glove box

Fix: Blower motor resistor block overheats and burns connector. Often the pigtail melts and must be replaced with the resistor. Resistor itself is behind glove box, 0.5-1 hour labor. If wiring harness is damaged, add 1-2 hours to splice in new connector. Cheap part, easy fix, happens to nearly every one eventually.

Estimated cost: $120-280