Glove Box

This procedure covers the removal and replacement of the glove box assembly in a 1994-2007 Dodge Ram 2500 with 5.9L Cummins diesel engine.

Warnings

Tools required

Parts

• Glove box assembly × 1 — Use OEM specification
• Glove box mounting screws × 4 — Typically included with new glove box
• Glove box door stop/damper × 1 — Use OEM specification if damaged

Preparation

1. Park vehicle on level surface and turn off ignition
2. Empty all contents from glove box compartment
3. If accessing components behind glove box (such as cabin air filter or blower motor), disconnect negative battery terminal
4. Ensure adequate lighting to see inside glove box opening

Procedure

1. 1

   Open glove box fully
   Open the glove box door to its fully open position. The door should rest against the door stops. If the glove box has a lock, unlock it before proceeding.
2. 2

   Remove door stop/damper if equipped
   Locate the door stop or damper mechanism on the right side of the glove box. This may be a plastic or rubber stop that prevents over-extension. Gently compress or squeeze the sides to release it from its mounting position. Some models use a friction-fit damper arm that can be unclipped by hand.
3. 3

   Locate hinge mounting screws
   With the door fully open, squeeze the sides of the glove box bin inward to release the molded side stop tabs from the dashboard slots. This generation of Ram 2500 uses a drop-down bin retained by flexible side tabs rather than hinge screws, so no side screws need to be removed.
4. 4

   Remove hinge screws
   With both side stop tabs squeezed clear of their dashboard slots, gently lower the glove box bin fully and lift it off its lower hinge pins to remove it. No screws are used to retain the bin on this generation.
   Torque spec

   Hinge Screws2 Nm (1.5 lb-ft)
5. 5

   Disconnect any electrical connections
   These trucks generally do not have a glove box light; if no light or connector is present, skip this step. If a light was aftermarket-added, carefully pull the bin away and press the connector release tab to disconnect it.
6. 6

   Remove glove box assembly
   With all screws removed and electrical connections disconnected, carefully pull the glove box assembly straight out from the dashboard opening. Maneuver it to clear any remaining attachment points or clips. Inspect the mounting points on the dashboard for any damage or broken tabs.
7. 7

   Inspect mounting points and hardware
   Examine the dashboard mounting points for any cracks, broken clips, or damaged threads. Inspect the removed glove box for broken hinge points or stripped screw holes. Check the condition of the door stop/damper and replace if worn or damaged.
8. 8

   Install new or repaired glove box
   Position the new or repaired glove box assembly into the dashboard opening. If equipped with a glove box light, reconnect the electrical connector before fully seating the assembly. Align the hinge points with the mounting holes in the dashboard.
9. 9

   Install and torque hinge screws
   Reinstall the glove box bin by seating its lower hinge pins into the dashboard pivots, then swing the bin up and squeeze the sides inward so the side stop tabs snap back into their dashboard slots. No torque wrench is required.
   Torque spec

   Hinge Screws2 Nm (1.5 lb-ft)
10. 10

    Reinstall door stop/damper
    Reinstall the door stop or damper mechanism by pressing it firmly into its mounting position until it clicks or seats fully. Ensure it moves freely and provides appropriate resistance when opening the glove box door.

Reassembly

1. Ensure all hinge screws are torqued to 2.0 Nm (1.5 lb-ft)
2. Verify electrical connections are secure if glove box light is present
3. Reconnect negative battery terminal if it was disconnected
4. Test glove box light operation if equipped

Verification

• Open and close glove box several times to ensure smooth operation and proper alignment
• Verify door stop/damper engages correctly and prevents over-extension
• Check that glove box latches securely when closed and lock functions properly if equipped
• Confirm glove box light illuminates when door is opened if equipped
• Inspect for any gaps or misalignment between glove box and dashboard trim

More procedures for this vehicle