Free API
suspension

Knuckle/Spindle - Rear

for 1994–2007 Dodge Ram 2500 5.9L I6 Cummins Diesel · 4WD
Difficulty
Advanced
Time
2.5 h
Tools
15
Steps
12
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

Replacement of the rear knuckle/spindle assembly on a 4WD Dodge Ram 2500 with 5.9L Cummins diesel engine, including bearing removal and installation.

Warnings

⚠️Vehicle must be securely supported on jack stands rated for its weight. Never work under a vehicle supported only by a floor jack.
⚠Rear differential fluid will drain when axle shaft is removed. Have a drain pan ready and plan to refill the differential.
⚠Pressing bearings requires significant force. Ensure press or C-clamp is properly aligned to avoid damaging the new spindle.
ℹ️This procedure assumes a full-floating rear axle design common to 2500 series trucks. Verify axle type before beginning work.

Tools required

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Fluids

  • 75W-90 synthetic gear oil — 1 qt

Preparation

  1. Park vehicle on level surface and place wheel chocks at front wheels
  2. Loosen rear wheel lug nuts while vehicle is on ground
  3. Raise rear of vehicle and support securely on jack stands under frame rails
  4. Remove rear wheel on side being serviced
  5. Place drain pan under rear differential to catch gear oil
  6. Spray all fasteners with penetrating oil and allow to soak for 15-20 minutes

Procedure

  1. 1
    Remove brake caliper and rotor
    Remove the brake caliper mounting bolts and hang caliper from frame using wire or bungee cord to avoid stressing the brake hose. Remove brake rotor from spindle. If rotor is stuck, use penetrating oil and light tapping with rubber mallet.
  2. 2
    Remove axle shaft
    Remove the bolts securing the axle shaft flange to the wheel hub (typically 8 on this full-floating axle). Carefully pull the axle shaft straight out of the axle tube. Minimal differential fluid should escape on a full-floating axle, but position a drain pan as a precaution. Support the axle shaft to prevent it from falling.
    ⚠Axle shaft can weigh 30-40 lbs. Support it properly when removing to prevent injury or damage.
  3. 3
    Remove hub and spindle assembly
    Remove the hub nut and washer from the spindle. Pull the hub assembly straight off the spindle along with outer bearing and seal. Set aside on clean surface. Remove the 4 nuts/bolts securing the spindle to the axle tube housing. Carefully remove the spindle assembly from the axle tube.
  4. 4
    Remove old bearings and races from hub
    Using a brass drift or seal puller, remove the inner bearing seal from the hub. Remove the inner bearing cone. Using a bearing race driver or brass punch, drive out both the inner and outer bearing races from inside the hub. Work around the race evenly to prevent cocking. Clean the hub thoroughly with brake cleaner and inspect for cracks or damage.
  5. 5
    Prepare new spindle
    Clean the new spindle thoroughly with brake cleaner. Inspect all bearing surfaces and threads for damage. If bearing races are not pre-installed in the hub, install new outer and inner bearing races using a bearing race driver. Ensure races are fully seated and square in their bores.
  6. 6
    Pack and install wheel bearings
    Pack both inner and outer wheel bearings thoroughly with high-temperature wheel bearing grease. Work grease completely through all rollers. Install inner bearing cone into hub, then carefully drive new inner seal into place using seal driver. Apply grease to seal lip. Coat spindle bearing surfaces with thin layer of grease.
    ℹ️Proper bearing packing is critical for longevity. Grease must be worked through all rollers, not just coated on outside.
  7. 7
    Install spindle to axle housing
    Install a new axle shaft seal in the axle tube if not already done. Clean the spindle mounting surface on axle tube. Position new spindle onto axle tube, ensuring proper alignment of bolt holes. Install the spindle mounting nuts/bolts (verify count against your spindle) and tighten evenly in a cross pattern to specification.
  8. 8
    Install hub assembly
    Carefully slide the hub assembly (with inner bearing and seal installed) onto the spindle. Install the outer bearing cone onto the spindle, followed by the inner adjusting nut, lock washer/ring, and outer locknut per the full-floating axle configuration. Hand-tighten the hub nut while rotating the hub to seat bearings. Adjust bearing preload according to the manufacturer's full-floating axle procedure: tighten the inner adjusting nut to approximately 50 ft-lbs while rotating the hub to seat the bearings, then back off completely and re-tighten the inner nut to the specified light preload (verify exact value in the service manual). Install the lock washer/pin, then install and torque the outer locknut to specification. Verify final bearing end play with a dial indicator.
    ℹ️Proper bearing preload adjustment is critical. Too tight causes premature bearing failure; too loose causes excessive play and noise.
  9. 9
    Install axle shaft
    Clean the axle shaft flange and hub mounting surfaces. Apply a thin film of gear oil to the axle shaft seal area. Carefully guide the axle shaft into the axle tube, ensuring it engages properly with the differential side gear. Align the axle shaft flange with the hub and install all 8 bolts. Tighten bolts in a star pattern to specification.
  10. 10
    Reinstall brake components
    Clean the brake rotor hub surface and spindle mating area with brake cleaner. Install the brake rotor onto the hub. Position the brake caliper over the rotor and install mounting bolts. Ensure brake pads are properly seated and brake hose is not twisted or kinked.
  11. 11
    Refill differential and install wheel
    If differential fluid was lost during service, top off or refill the rear differential with the correct gear oil (verify grade and the ~3+ quart capacity in the service manual) to the proper level at the fill plug. If the axle is a limited-slip unit, add the required friction modifier. Install the fill plug. Install the wheel and hand-tighten lug nuts in a star pattern.
  12. 12
    Lower vehicle and final torque
    Lower the vehicle until the tire just touches the ground but weight is still on jack stands. Torque wheel lug nuts to specification in a star pattern. Fully lower vehicle and perform final lug nut torque check.
    ℹ️Always perform final lug nut torque with vehicle weight on ground to ensure proper seating.

Reassembly

  1. Pump brake pedal several times to ensure proper caliper piston position before moving vehicle
  2. Check for any fluid leaks around differential and axle seals after 50-100 miles of driving
  3. Verify differential fluid level after initial test drive
  4. Re-torque wheel lug nuts after 50 miles of driving

Verification

  • Rotate wheel by hand to verify smooth rotation with no binding or excessive play
  • Check hub end play - should be 0.001-0.005 inches with dial indicator if available
  • Verify no leaks from axle shaft seal or differential
  • Test drive vehicle and verify no unusual noises, vibrations, or pulling
  • Check that brake operation is normal with no pulsation or grabbing
  • Verify wheel lug nuts are torqued to specification after test drive
🔧Stuck on this knuckle/spindle - rear? Take it to The Diag Desk.A human with 20+ years in the bay answers about YOUR Dodge within 24 hours — never AI. $25, and you're not charged unless you get an answer.Ask a tech →

More procedures for this vehicle

For shop owners
Want more customers to find you?
We build shop websites with online booking onto your schedule and your own online store.
Talk to the ownerSee what's included
Built by a shop owner. Talk to Chris, not a sales rep.
🔧 Built by master technician Chris Hackleman · Master Technician · 20+ years. Spot an error? Use the Help link above — a human reads every report.
Stuck on this repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
🔓 LIBERATED FOREVER
The 1994–2007 Dodge Ram 2500 5.9L I6 Cummins Diesel repair data is free for every DIYer and shop on earth, permanently, because Timmehster paid $99 to unlock it.
Mitchell1 charges $169/mo for this. ALLDATAdiy charges $30/yr per vehicle. Open Labor Project is free permanently, because of community sponsors like Timmehster.
Free another vehicle →
Building an app?
Free API key: 10 requests/day, 100/month, no card required.
Get an API key →
Run a shop?
A free website, SEO and Google reviews with your shop software. Auto Shop Base Professional, $250/mo, with our labor times on every estimate.
See what's included →