Free API
engine

Oil Pressure Sensor

for 1994–2007 Dodge Ram 2500 5.9L I6 Cummins Diesel · 4WD
Difficulty
Easy
Time
54 min
Tools
7
Steps
9
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

This procedure covers removal and replacement of the oil pressure sensor on the 5.9L Cummins diesel engine, located on the engine block near the oil filter housing.

Warnings

⚠Perform this repair with the engine cold to avoid burns from hot oil and components
ℹ️Some oil spillage is normal when removing the sensor; have towels ready
⚠Do not overtighten the sensor as the threads are in the aluminum engine block and can strip

Tools required

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Preparation

  1. Park vehicle on level ground and engage parking brake
  2. Allow engine to cool completely if recently operated
  3. Disconnect negative battery terminal to prevent false fault codes
  4. Locate oil pressure sensor on driver side of engine block, above oil filter housing and below fuel injection pump

Procedure

  1. 1
    Access the oil pressure sensor
    Open hood and secure with prop rod. The oil pressure sensor is located on the driver side of the engine block, positioned between the oil filter housing and the fuel injection pump. You may need to move wiring harnesses aside for better access, but complete removal is typically not necessary.
  2. 2
    Disconnect electrical connector
    Press the release tab on the electrical connector and pull straight away from the sensor. Avoid twisting or pulling on the wires themselves. If connector is corroded or stuck, spray with electrical contact cleaner and allow to penetrate before removal.
  3. 3
    Position drain pan
    Place a small drain pan or shop towels below the sensor location. Expect approximately 1/4 to 1/2 cup of engine oil to drain from the sensor port when removed. This oil loss is normal and does not require a full oil change.
  4. 4
    Remove oil pressure sensor
    Using a 22mm deep socket and ratchet, turn the sensor counterclockwise to remove. The sensor may be tight due to thread sealant from factory installation. If the sensor is extremely difficult to remove, apply penetrating oil around the base and wait 10-15 minutes before attempting again. Once loosened, sensor can be unthreaded by hand for final removal.
  5. 5
    Clean sensor port
    Use a wire brush to clean the threads in the engine block sensor port. Remove any old thread sealant, oil residue, or debris. Wipe area clean with a shop towel. Inspect threads for damage; if threads are damaged, the block may require thread repair before proceeding.
  6. 6
    Prepare new sensor
    Apply a thin, even coat of thread sealant with Teflon to the threads of the new oil pressure sensor. Do not apply sealant to the first thread to prevent contamination of the oil system. Allow sealant to become tacky according to manufacturer directions, typically 1-2 minutes.
  7. 7
    Install new oil pressure sensor
    Thread the new sensor into the engine block by hand, turning clockwise until finger-tight. Ensure sensor threads in smoothly without cross-threading. Once hand-tight, use the 22mm socket and torque wrench to tighten to specification.
    Torque spec
    Oil Pressure Sensor20 Nm (15 lb-ft)
  8. 8
    Reconnect electrical connector
    Push the electrical connector firmly onto the new sensor until you hear or feel a distinct click, confirming the locking tab has engaged. Gently tug on the connector to verify it is securely attached. Route any displaced wiring back to original position.
  9. 9
    Reconnect battery and check oil level
    Reconnect the negative battery terminal. Check engine oil level on dipstick and add 15W-40 diesel engine oil if necessary to bring level to the full mark. The small amount lost during sensor replacement typically does not require adding oil unless level was already low.

Reassembly

  1. Ensure all wiring harnesses are routed away from hot exhaust components and moving parts
  2. Verify electrical connector is fully seated and locked to sensor
  3. Wipe any spilled oil from engine block to prevent smoking on first startup

Verification

  • Start engine and immediately verify oil pressure gauge shows normal reading (10-15 psi at idle when warm, 30-40 psi at highway speeds)
  • Check for oil leaks around sensor base while engine is running
  • Allow engine to reach operating temperature and verify no oil pressure warning lights illuminate
  • Check for diagnostic trouble codes using scan tool; clear any codes related to oil pressure sensor circuit if present
  • Test drive vehicle and confirm oil pressure gauge responds appropriately to engine speed changes

Related trouble codes on this vehicle

Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.

Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →

🔧Stuck on this oil pressure sensor? Take it to The Diag Desk.A human with 20+ years in the bay answers about YOUR Dodge within 24 hours — never AI. $25, and you're not charged unless you get an answer.Ask a tech →

More procedures for this vehicle

For shop owners
Want more customers to find you?
We build shop websites with online booking onto your schedule and your own online store.
Talk to the ownerSee what's included
Built by a shop owner. Talk to Chris, not a sales rep.
🔧 Built by master technician Chris Hackleman · Master Technician · 20+ years. Spot an error? Use the Help link above — a human reads every report.
Stuck on this repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
🔓 LIBERATED FOREVER
The 1994–2007 Dodge Ram 2500 5.9L I6 Cummins Diesel repair data is free for every DIYer and shop on earth, permanently, because Timmehster paid $99 to unlock it.
Mitchell1 charges $169/mo for this. ALLDATAdiy charges $30/yr per vehicle. Open Labor Project is free permanently, because of community sponsors like Timmehster.
Free another vehicle →
Building an app?
Free API key: 10 requests/day, 100/month, no card required.
Get an API key →
Run a shop?
A free website, SEO and Google reviews with your shop software. Auto Shop Base Professional, $250/mo, with our labor times on every estimate.
See what's included →