Free API
cooling

Thermostat

for 1994–2007 Dodge Ram 2500 5.9L I6 Cummins Diesel · 4WD
Difficulty
Easy
Time
1.5 h
Tools
9
Steps
13
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

Replace the thermostat and housing gasket on the 5.9L Cummins diesel engine to restore proper engine operating temperature.

Warnings

⚠️Never open the cooling system when the engine is hot. Allow engine to cool completely for at least 2 hours to avoid severe burns from pressurized coolant.
⚠Ethylene glycol coolant is toxic to animals and humans. Clean up any spills immediately and dispose of old coolant properly.
ℹ️The thermostat housing is located on the driver side front of the engine block, below the injection pump.

Tools required

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Fluids

  • Ethylene glycol 50/50 coolant — 2 qt

Preparation

  1. Ensure engine is completely cold before beginning work
  2. Park vehicle on level surface and engage parking brake
  3. Place drain pan under the front of the engine below the thermostat housing area
  4. Remove the negative battery cable if additional clearance is needed
  5. Locate the petcock drain or lower radiator hose to drain coolant partially

Procedure

  1. 1
    Drain coolant from system
    Open the radiator petcock or carefully loosen the lower radiator hose clamp at the radiator to drain approximately 2-3 gallons of coolant into the drain pan. You do not need to drain the entire system, only enough to drop the level below the thermostat housing.
  2. 2
    Remove coolant temperature sensor
    Disconnect the electrical connector from the coolant temperature sensor on the thermostat housing. Using the appropriate socket, carefully remove the coolant temperature sensor from the housing. Inspect the sensor for damage or corrosion and replace if necessary. Set aside for reinstallation.
    ⚠Some residual coolant will drain from the sensor hole when removed. Have shop towels ready.
  3. 3
    Disconnect coolant hoses
    Loosen the hose clamp on the upper radiator hose connected to the thermostat housing. Twist and pull the hose off the housing connection. If the hose is stuck, carefully use a screwdriver to break the seal, being careful not to damage the hose barb.
  4. 4
    Remove thermostat housing bolts
    Remove the thermostat housing mounting bolts from the front of the cylinder head. There are typically 2 bolts securing the housing. Keep track of bolt locations as they may be different lengths.
    Torque spec
    Thermostat Housing Bolt15 Nm (11 lb-ft)
  5. 5
    Remove thermostat housing and old thermostat
    Carefully pull the thermostat housing away from the cylinder head. Remove the old thermostat from the housing or head recess, noting the orientation of the thermostat (spring side typically faces into the engine). Remove and discard the old gasket.
  6. 6
    Clean mating surfaces
    Thoroughly clean all gasket material from both the thermostat housing and engine block mating surfaces using a scraper or gasket removal tool. Ensure surfaces are completely clean and dry with no debris, old gasket material, or corrosion remaining. Wipe clean with shop towels.
  7. 7
    Install new thermostat
    Place the new thermostat into the recess in the cylinder head with the spring side facing into the engine and the air bleed valve (small hole or pin) positioned at the top. Verify the thermostat seats properly in the recess.
  8. 8
    Install new gasket and housing
    Position the new thermostat housing gasket onto the cylinder head, aligning all bolt holes. A small amount of RTV silicone on both sides of the gasket can help hold it in place and ensure a better seal, though this is optional. Carefully position the thermostat housing over the thermostat and gasket, ensuring the thermostat remains properly seated.
  9. 9
    Torque thermostat housing bolts
    Install all thermostat housing bolts hand-tight, ensuring the housing is properly seated and gasket is not pinched. Torque bolts in a criss-cross pattern to 24.0 Nm (18.0 lb-ft). Do not overtighten as this can crack the housing or distort the sealing surface.
    Torque spec
    Thermostat Housing Bolt15 Nm (11 lb-ft)
  10. 10
    Reinstall coolant temperature sensor
    Apply thread sealant to the threads of the coolant temperature sensor. Thread the sensor into its bore by hand until seated, then torque per service manual specification. Reconnect the electrical connector to the sensor.
    Torque spec
    Coolant Temperature Sensor20 Nm (15 lb-ft)
  11. 11
    Reconnect coolant hoses
    Reinstall both upper and lower coolant hoses onto the thermostat housing connections. Ensure hoses are fully seated onto the barbs. Position hose clamps over the hose connection area and tighten securely.
  12. 12
    Refill cooling system
    Close the radiator petcock or reconnect the lower radiator hose if it was removed. Refill the cooling system with proper 50/50 ethylene glycol coolant mixture through the radiator cap opening. Fill slowly to allow air to escape. Top off the overflow reservoir to the cold fill line.
  13. 13
    Burp cooling system
    With the radiator cap still off, start the engine and allow it to warm up to operating temperature while monitoring coolant level. Add coolant as needed as air purges from the system. The thermostat will open when it reaches operating temperature (you will see coolant circulation increase). Squeeze upper radiator hose to help purge air bubbles. Once thermostat opens and no more air bubbles appear, top off radiator and install cap.

Reassembly

  1. Reconnect negative battery cable if it was removed
  2. Clean up any coolant spills from engine bay and under vehicle
  3. Dispose of old coolant according to local regulations

Verification

  • Start engine and verify no coolant leaks around thermostat housing, hoses, or temperature sensor
  • Monitor engine temperature gauge to ensure it reaches normal operating range (approximately 180-195°F)
  • Verify heater produces hot air when engine reaches operating temperature
  • Check coolant level in overflow reservoir after engine cools and top off if necessary
  • After first test drive, recheck coolant level and inspect for leaks

Related trouble codes on this vehicle

Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.

Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →

🔧Stuck on this thermostat? Take it to The Diag Desk.A human with 20+ years in the bay answers about YOUR Dodge within 24 hours — never AI. $25, and you're not charged unless you get an answer.Ask a tech →

More procedures for this vehicle

For shop owners
Want more customers to find you?
We build shop websites with online booking onto your schedule and your own online store.
Talk to the ownerSee what's included
Built by a shop owner. Talk to Chris, not a sales rep.
🔧 Built by master technician Chris Hackleman · Master Technician · 20+ years. Spot an error? Use the Help link above — a human reads every report.
Stuck on this repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
🔓 LIBERATED FOREVER
The 1994–2007 Dodge Ram 2500 5.9L I6 Cummins Diesel repair data is free for every DIYer and shop on earth, permanently, because Timmehster paid $99 to unlock it.
Mitchell1 charges $169/mo for this. ALLDATAdiy charges $30/yr per vehicle. Open Labor Project is free permanently, because of community sponsors like Timmehster.
Free another vehicle →
Building an app?
Free API key: 10 requests/day, 100/month, no card required.
Get an API key →
Run a shop?
A free website, SEO and Google reviews with your shop software. Auto Shop Base Professional, $250/mo, with our labor times on every estimate.
See what's included →