Free API
exhaust

Catalytic Converter - California

for 2000 Dodge Viper 8.0L V10 · RWD
Difficulty
Advanced
Time
3.4 h
Tools
15
Steps
15
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

Replacement of California emissions-compliant catalytic converters on a 1992 Dodge Viper 8.0L V10, including oxygen sensor removal, exhaust component disconnection, and installation of new converters with proper torque specifications.

Warnings

⚠️Exhaust system operates at extremely high temperatures (700°F+). Allow engine and exhaust to cool completely for at least 2 hours before beginning work. Severe burns will result from contact with hot components.
⚠️Vehicle must be supported on jack stands rated for the vehicle weight. Never work under a vehicle supported only by a floor jack.
⚠Exhaust fasteners are subject to corrosion and heat cycling. Apply penetrating oil 30+ minutes before disassembly to minimize breakage risk. Replacement fasteners may be required.
⚠California-compliant catalytic converters must meet CARB standards. Verify replacement parts have valid CARB Executive Order (EO) numbers if using aftermarket components.
ℹ️The 1992 Viper uses side-exit exhaust with catalytic converters located in the mid-section of the exhaust system ahead of the side-exit pipes. This procedure addresses replacement of both driver and passenger side converters.

Tools required

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Preparation

  1. Park vehicle on level surface and apply parking brake. Place wheel chocks behind rear wheels.
  2. Ensure engine and exhaust system are completely cold (minimum 2 hours after last operation).
  3. Raise front of vehicle with floor jack and support securely on jack stands at manufacturer-specified jacking points.
  4. Spray all exhaust flange bolts, oxygen sensor threads, and hanger bolt connections with penetrating oil. Allow to soak for 30+ minutes before proceeding.
  5. Visually inspect exhaust system to identify catalytic converter locations, oxygen sensor positions, and exhaust hanger points.

Procedure

  1. 1
    Disconnect oxygen sensors
    Locate the oxygen sensors positioned in the exhaust system upstream of each catalytic converter. Disconnect the electrical connectors by pressing the release tab and pulling apart. Using a 22mm oxygen sensor socket, turn counterclockwise to remove each oxygen sensor. Inspect sensor threads for damage. If threads are damaged or sensor is older than 60,000 miles, replace with new sensors. Set sensors aside in a clean location.
  2. 2
    Remove driver side heat shield
    Locate the heat shield covering the driver side catalytic converter. Remove the heat shield mounting bolts (typically 3-4 bolts depending on specific heat shield design). Use a 10mm socket to remove bolts. Lower heat shield away from exhaust system and set aside. If heat shield is damaged or excessively corroded, replacement is recommended.
  3. 3
    Disconnect driver side catalytic converter upstream flange
    Locate the upstream exhaust flange connection between the exhaust manifold downpipe and the catalytic converter inlet. Remove the 2 flange bolts using a 15mm socket and wrench. Work bolts back and forth if corrosion is present. Once bolts are removed, separate the flange connection. Remove and discard the old exhaust gasket.
  4. 4
    Disconnect driver side catalytic converter downstream flange
    Locate the downstream exhaust flange connection between the catalytic converter outlet and the intermediate pipe. Remove the 2 flange bolts using a 15mm socket and wrench. Separate the flange connection. Remove and discard the old exhaust gasket.
  5. 5
    Remove driver side catalytic converter from hangers
    Support the catalytic converter assembly by hand. Identify the rubber exhaust hanger(s) supporting the converter assembly. Using a pry bar or exhaust hanger removal tool, work the exhaust hanger loop out of the rubber mount. The converter assembly should now be free. Lower and remove the driver side catalytic converter from the vehicle.
  6. 6
    Remove passenger side heat shield
    Repeat heat shield removal process for the passenger side catalytic converter. Remove the heat shield mounting bolts (typically 3-4 bolts) using a 10mm socket. Lower heat shield away from exhaust system and set aside.
  7. 7
    Disconnect passenger side catalytic converter upstream flange
    Locate the upstream exhaust flange connection between the exhaust manifold downpipe and the catalytic converter inlet on the passenger side. Remove the 2 flange bolts using a 15mm socket and wrench. Separate the flange connection and remove and discard the old exhaust gasket.
  8. 8
    Disconnect passenger side catalytic converter downstream flange
    Locate the downstream exhaust flange connection between the catalytic converter outlet and the intermediate pipe on the passenger side. Remove the 2 flange bolts using a 15mm socket and wrench. Separate the flange connection and remove and discard the old exhaust gasket.
  9. 9
    Remove passenger side catalytic converter from hangers
    Support the catalytic converter assembly by hand. Identify the rubber exhaust hanger(s) supporting the converter assembly. Using a pry bar or exhaust hanger removal tool, work the exhaust hanger loop out of the rubber mount. Lower and remove the passenger side catalytic converter from the vehicle.
  10. 10
    Prepare flange surfaces and install new driver side catalytic converter
    Using a wire brush, clean all exhaust flange surfaces on the driver side to remove carbon deposits, old gasket material, and corrosion. Ensure flange surfaces are flat and clean. Position the new driver side California-compliant catalytic converter into place, aligning the exhaust hanger loops with the rubber mounts. Press hanger loops firmly into rubber mounts. Install new exhaust gaskets at both upstream and downstream flange connections. Start all flange bolts by hand to ensure proper thread engagement before tightening.
  11. 11
    Torque driver side catalytic converter flange connections
    Apply anti-seize compound to the threads of all flange bolts. Using a torque wrench, tighten the upstream flange bolts (manifold connection) to specification in a cross-pattern. Then torque the downstream flange bolts (intermediate pipe connection) to specification in a cross-pattern. Ensure converter assembly is properly seated and aligned before final torque.
  12. 12
    Prepare and install passenger side catalytic converter
    Using a wire brush, clean all exhaust flange surfaces on the passenger side to remove carbon deposits, old gasket material, and corrosion. Position the new passenger side California-compliant catalytic converter into place, aligning the exhaust hanger loops with the rubber mounts. Press hanger loops firmly into rubber mounts. Install new exhaust gaskets at both upstream and downstream flange connections. Start all flange bolts by hand to ensure proper thread engagement before tightening.
  13. 13
    Torque passenger side catalytic converter flange connections
    Apply anti-seize compound to the threads of all flange bolts. Using a torque wrench, tighten the upstream flange bolts (manifold connection) to specification in a cross-pattern. Then torque the downstream flange bolts (intermediate pipe connection) to specification in a cross-pattern. Ensure converter assembly is properly seated and aligned before final torque.
  14. 14
    Install oxygen sensors
    Apply a thin layer of anti-seize compound to the threads of each oxygen sensor. Do not allow anti-seize to contact the sensor tip. Thread each oxygen sensor into its bung by hand until finger-tight. Using the 22mm oxygen sensor socket and torque wrench, tighten each sensor to specification. Reconnect the electrical connectors to each oxygen sensor, ensuring the connector locks securely with an audible click.
  15. 15
    Reinstall heat shields
    Position the driver side heat shield over the catalytic converter. Install heat shield mounting bolts and tighten to specification using a 10mm socket and torque wrench. Repeat for the passenger side heat shield. Ensure heat shields are properly positioned and do not contact moving components or create rattle points.

Reassembly

  1. Visually inspect all flange connections to ensure bolts are properly torqued and gaskets are seated correctly.
  2. Check all exhaust hangers to verify they are fully engaged in rubber mounts.
  3. Verify oxygen sensor electrical connectors are secure and wiring is routed away from hot exhaust components.
  4. Lower vehicle from jack stands carefully, ensuring all tools and parts have been removed from under the vehicle.

Verification

  • Start engine and allow to idle. Listen for exhaust leaks at all flange connections. Any hissing or ticking noise indicates a leak requiring immediate attention.
  • Visually inspect all connections while engine is running (from a safe distance) for visible exhaust gas escaping from flanges or sensor bungs.
  • Allow engine to reach operating temperature and verify no exhaust odors are present in the cabin.
  • If Check Engine Light illuminates, use an OBD-I diagnostic tool to retrieve codes. Verify oxygen sensors are functioning properly (no sensor codes present).
  • After initial test drive (10-15 miles), re-inspect all flange bolts and oxygen sensors for proper torque. Retorque if necessary after heat cycling.
  • Verify catalytic converters meet California CARB requirements by confirming EO number marking on converter body matches documentation.

Related trouble codes on this vehicle

Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.

Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →

🔧Stuck on this catalytic converter - california? Take it to The Diag Desk.A human with 20+ years in the bay answers about YOUR Dodge within 24 hours — never AI. $25, and you're not charged unless you get an answer.Ask a tech →

More procedures for this vehicle

For shop owners
Want more customers to find you?
We build shop websites with online booking onto your schedule and your own online store.
Talk to the ownerSee what's included
Built by a shop owner. Talk to Chris, not a sales rep.
🔧 Built by master technician Chris Hackleman · Master Technician · 20+ years. Spot an error? Use the Help link above — a human reads every report.
Stuck on this repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
⚠ STILL BEHIND THE PAYWALL
The 2000 Dodge Viper repair data is incomplete because no one has sponsored it yet. For $99, we generate the full step-by-step procedures, then fact-check them with a second AI pass and your expert review. Your name on every procedure, permanently.
The same data would cost $169/mo from Mitchell1 or $30/year from ALLDATAdiy — and you'd be renting access, not freeing it. Sponsor once, free forever.
Sponsor the Dodge Viper — $99 →
Building an app?
Free API key: 10 requests/day, 100/month, no card required.
Get an API key →
Run a shop?
A free website, SEO and Google reviews with your shop software. Auto Shop Base Professional, $250/mo, with our labor times on every estimate.
See what's included →