body

Side Mirror Glass

for 2000 Dodge Viper 8.0L V10 · RWD

Difficulty

Easy

Time

30 min

Tools

Steps

✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

This procedure covers removal and replacement of the side mirror glass on a 1992 Dodge Viper, including manual adjustment mirror glass removal and installation.

Warnings

⚠Mirror glass is fragile and has sharp edges when broken. Wear gloves if handling cracked or broken glass.

ℹ️The 1992 Viper uses manual non-powered side mirrors with mechanical ball-and-socket adjustment.

Tools required

Flat-blade trim tool or plastic pry toolEssential

Clean microfiber cloth

Masking tape

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

Side mirror glass × 1 — Use OEM specification - specify driver or passenger side
Mirror adhesive pad or backing plate (if damaged) × 1 — Use OEM specification

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Preparation

Park vehicle on level surface and ensure it will not roll
If replacing broken glass, apply masking tape across cracked mirror to contain shards during removal
Clean the mirror housing exterior to prevent debris from entering during disassembly

Procedure

1
Access Mirror Glass Attachment
Open the door for the mirror being serviced. Examine the back side of the mirror glass from the door opening. The mirror glass is retained to the mirror housing by a backing plate that clips or adheres to the mirror adjustment mechanism. On the 1992 Viper manual mirror, examine how the glass is retained — it may attach via an adhesive backing plate, spring clips, or a pivot mechanism visible from behind the mirror housing. Confirm the actual attachment type before proceeding.
2
Release Mirror Glass from Backing Plate
Insert a flat-blade trim tool or plastic pry tool between the mirror glass edge and the mirror housing at the inboard edge (closest to the door). Gently apply outward pressure to disengage the mirror glass from its backing plate or mounting clips. Work around the perimeter of the mirror glass if resistance is encountered. The glass typically snaps onto a backing plate with spring clips or is bonded with adhesive pads. If adhesive-mounted, apply steady pressure to break the adhesive bond.
3
Remove Mirror Glass Assembly
Once the clips or adhesive are released, carefully pull the mirror glass away from the housing. Note the orientation of any backing plate, adjustment ball socket, or retaining clips that remain attached to either the glass or the housing. If the backing plate remains in the housing, remove it by hand or with the trim tool. Inspect the backing plate and ball socket for damage or wear.
4
Prepare New Mirror Glass
If the new mirror glass does not include a backing plate or adhesive pad, transfer the backing plate from the old glass to the new glass. Ensure the backing plate is clean and free of old adhesive residue. If using adhesive pads, clean both the back of the new mirror glass and the ball socket on the mirror housing with a clean cloth. Remove the protective liner from any new adhesive pad and apply it to the backing plate or directly to the mirror glass back.
5
Install New Mirror Glass
Align the new mirror glass with the ball socket or mounting clips in the mirror housing. Ensure the backing plate engages the adjustment mechanism correctly so that manual adjustment from inside the vehicle functions properly. Press the mirror glass firmly into place until the clips engage or the adhesive seats fully. If clip-retained, you should hear or feel the clips snap into position. Apply firm, even pressure across the entire back of the mirror glass for 15-30 seconds if adhesive-mounted.
6
Test Mirror Adjustment
From inside the vehicle, operate the manual mirror adjustment lever or knob to verify the mirror glass moves freely in all directions and holds position. The mirror should pivot smoothly on the ball socket without binding or slipping. Adjust the mirror to the desired viewing angle.

Reassembly

No disassembly of surrounding components is required for this procedure
Ensure mirror glass is securely seated before returning vehicle to service

Verification

Verify mirror glass is firmly attached and does not rattle or move when touched
Confirm manual adjustment mechanism operates smoothly through full range of motion
Check mirror viewing angle from driver position and adjust as needed
Inspect for proper seating with no gaps between glass and housing