electrical

Blower Motor

for 2006 Dodge Viper 8.3L V10 · RWD

Difficulty

Moderate

Time

1.2 h

Tools

Steps

✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

Remove and replace the blower motor assembly located in the HVAC housing under the passenger side of the dashboard.

Warnings

⚠Disconnect the battery negative terminal and wait 2 minutes before starting work to avoid airbag deployment risk.

ℹ️The blower motor is located in a tight area under the passenger side dashboard. A flexible extension or swivel socket may improve access.

Tools required

7mm socket or nut driverEssential

8mm socketEssential

1/4" ratchet with short extensionEssential

Trim panel removal tool set

Flashlight or work lightEssential

Shop towel or rag

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

Blower motor assembly × 1 — Use OEM specification
Blower motor resistor (if damaged) × 1 — Use OEM specification

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Preparation

Park vehicle on level ground and set parking brake
Turn ignition off and remove key
Disconnect battery negative terminal and wait 2 minutes
Allow HVAC system to cool if recently operated

Procedure

1
Access passenger side lower dash area
Open the passenger door fully. Move the passenger seat fully rearward if possible to gain working room. Note that the 2005 Viper has a very tight two-seat cabin; access to the underside of the dash is extremely limited. Position yourself on the passenger side floor to access the underside of the dashboard.
2
Locate blower motor assembly
The blower motor is mounted in the HVAC housing on the passenger side of the vehicle, accessible from below the dashboard. It is a cylindrical unit approximately 4-5 inches in diameter with an electrical connector on the side and cooling tubes visible. Use a flashlight to identify the motor and its mounting fasteners.
3
Disconnect blower motor electrical connector
Locate the electrical connector on the side of the blower motor housing. Press the locking tab on the connector and pull it straight away from the motor. If access is tight, gently wiggle the connector while maintaining pressure on the release tab.
4
Remove blower motor cooling tube
The blower motor has a rubber or foam cooling tube connecting it to the HVAC case for ventilation. Gently pull the cooling tube off the motor housing. It is a friction fit and does not require tools. Set aside for reinstallation.
5
Remove blower motor mounting screws
Remove the screws securing the blower motor to the HVAC housing (confirm exact count and fastener size against 2005 Viper service documentation before proceeding). The screws are arranged around the perimeter of the motor flange. Support the motor with one hand while removing the final screw to prevent it from dropping. The screws are arranged around the perimeter of the motor flange. Support the motor with one hand while removing the final screw to prevent it from dropping.
6
Remove blower motor assembly
Carefully rotate and maneuver the blower motor assembly downward and out from the HVAC housing. The motor with attached fan cage must be angled to clear the housing opening. Work slowly to avoid damaging the fan blades or housing. Once clear of the housing, remove the assembly from the vehicle.
7
Inspect blower motor resistor
With the blower motor removed, inspect the blower motor resistor (if visible in the housing). It is typically mounted near the blower motor opening and secured with 2 screws. Check for signs of burning, corrosion, or melted connectors. If damaged, remove the resistor mounting screws (confirm exact count against 2005 Viper service documentation) and replace the resistor.
Torque spec
Blower Motor Resistor Screws2 Nm (1.5 lb-ft)
8
Install new blower motor assembly
Position the new blower motor assembly with fan cage into the HVAC housing opening. Rotate and angle the assembly to align the mounting flange with the screw holes in the housing. Ensure the motor is fully seated against the housing before fastening.
9
Install blower motor mounting screws
Install the 3 mounting screws through the motor flange and into the HVAC housing. Start all screws by hand before tightening to ensure proper alignment. Tighten screws in a criss-cross pattern, snug but not overtightened to avoid stripping the plastic housing (confirm any published torque value and fastener size against 2005 Viper service documentation).
10
Reconnect cooling tube and electrical connector
Push the cooling tube firmly onto the blower motor housing until fully seated. Connect the electrical connector to the blower motor, pressing until the locking tab clicks into place. Gently tug on the connector to verify it is secure.
11
Reconnect battery and test operation
Reconnect the battery negative terminal. Turn the ignition to the ON position (engine off). Test the blower motor at every available fan speed setting on the HVAC control. Verify smooth operation with no unusual noise, vibration, or burning smell. Check that airflow is consistent at each speed setting.

Reassembly

Return passenger seat to original position
Verify all electrical connections are secure and no tools or parts are left in the dash area
If blower motor resistor was replaced, verify proper connection and mounting