interior

Center Console

for 2006 Dodge Viper 8.3L V10 · RWD

Difficulty

Moderate

Time

1.9 h

Tools

Steps

✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

Remove and replace the center console assembly on a 2005 Dodge Viper, including disconnecting electrical connections and removing mounting hardware.

Warnings

⚠Disconnect the negative battery cable and wait 2 minutes before beginning work to allow airbag system capacitors to discharge.

ℹ️The Viper center console houses the climate control system and power window switches; ensure all electrical connections are labeled or photographed before disconnection.

⚠Avoid using excessive force on trim clips as they can break easily; use proper panel removal tools to prevent damage.

Tools required

Panel trim removal tool setEssential

Phillips screwdriverEssential

Flathead screwdriver

Socket set (metric)Essential

Ratchet with extensionsEssential

Torque wrenchEssential

Flashlight or work light

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

Center console assembly × 1 — Use OEM specification

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Preparation

Park vehicle on level surface and engage parking brake.
Disconnect negative battery cable and wait 2 minutes for airbag system discharge.
Move both seats fully rearward to provide maximum working room.
Photograph or label all electrical connections before disconnection for reference during reinstallation.

Procedure

1
Remove shifter trim bezel
Starting at the rear of the shifter boot, carefully pry up the shifter trim bezel using a panel removal tool. The bezel is retained by clips around its perimeter. Lift upward and away from the console once all clips are released. Note: Disconnect the negative battery cable before beginning work to prevent short circuits when handling electrical connectors.
2
Disconnect shifter boot
With the shifter trim bezel removed, locate the shifter boot attached to the transmission tunnel. Pull the boot upward off the shifter mechanism. No fasteners secure the boot; it is friction-fit over the shifter.
3
Remove console front mounting screws
Locate and remove the 2 Phillips screws at the front of the console near the dashboard interface. These screws are visible once the shifter trim is removed. Set screws aside in a container.
Torque spec
Console Screws3 Nm (2 lb-ft)
4
Remove armrest/storage compartment lid
Open the center console storage compartment lid fully. Locate the hinge pins or release tabs at the rear of the lid. Press the release tabs inward and lift the lid away from the console body.
5
Remove console rear mounting bolts
Inside the storage compartment, locate the 2 mounting bolts securing the rear of the console to the transmission tunnel. Use a socket and extension to remove these bolts (verify socket size against OEM specification). Retain bolts for reinstallation.
6
Disconnect power window switch harness
Inspect the console for any switch assemblies (e.g., window, hazard, or accessory switches). If present, press the locking tab on the electrical connector and pull the harness free from the switch assembly. Press the locking tab on the electrical connector and pull the harness free from the switch assembly.
7
Disconnect climate control electrical connections
If any console-mounted controls are present, locate their electrical connectors at the front of the console near the dashboard. Depress the locking tabs on each connector and carefully disconnect the harnesses. There are typically 2-3 connectors depending on climate control configuration.
8
Check for additional wiring
Inspect the console area for any additional electrical connections such as accessory power outlets, heated seat switches, or other optional equipment wiring. Disconnect any remaining harnesses by depressing their locking tabs.
9
Remove center console assembly
With all fasteners and electrical connections removed, grasp the console firmly at both front and rear. Lift upward and rearward to disengage the console from the transmission tunnel. Maneuver the console carefully past the shifter and out of the vehicle. The console may require slight angling to clear the seats and door sills.

Reassembly

Installation is the reverse of removal with the following notes:
Ensure all electrical harnesses are routed as originally installed and not pinched under the console.
Align the console carefully over the shifter before lowering into position.
Torque rear mounting bolts to specification: 27.0 Nm (20.0 lb-ft).
Torque front console screws to specification: 3.0 Nm (2.0 lb-ft).
Verify all trim clips are properly seated and the shifter trim bezel is flush with surrounding surfaces.
Reconnect the negative battery cable and verify operation of power windows, climate control, and all console-mounted switches.

Verification

Verify the console is firmly mounted with no movement or rattles.
Test all power window switches to ensure proper operation.
Verify climate control functionality including fan speeds, temperature control, and mode selection.
Check that the shifter operates smoothly without interference from the console or boot.
Verify all trim pieces are flush and properly seated with no gaps.
Ensure the storage compartment lid opens and closes smoothly.

🔧Stuck on this center console? Take it to The Diag Desk.A human with 20+ years in the bay answers about YOUR Dodge within 24 hours — never AI. $25, and you're not charged unless you get an answer.Ask a tech →