body
Grille
for 2006 Dodge Viper 8.3L V10 · RWD
Difficulty
Easy
Time
1.0 h
Tools
6
Steps
10
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.
Remove and replace the front grille assembly on a 2005 Dodge Viper, including disconnection of any integrated components.
Warnings
⚠The front fascia and grille are painted components. Use care when handling to avoid scratches or damage to the finish.
ℹ️Work on a cool vehicle. If the engine has been running, allow adequate cooling time before working near the radiator area.
Tools required
As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.
Parts
- Front grille assembly × 1 — Use OEM specification
- Push-pin retainers (if damaged) × 6 — Use OEM specification
As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.
Preparation
- Park vehicle on level surface and engage parking brake
- Open hood and secure in raised position
- If desired, protect adjacent painted surfaces with masking tape to prevent accidental contact damage during grille removal
Procedure
- 1Access upper grille fastenersFrom the engine bay, locate the upper edge of the grille assembly behind the hood opening. Identify the fastener locations along the top edge of the grille where it mounts to the radiator support structure.
- 2Remove upper grille mounting screwsRemove the 4 upper mounting screws securing the grille to the radiator support using a T25 Torx driver. These screws are located along the top edge of the grille, accessible from the engine bay.Torque specGrille Mounting Screws3 Nm (2 lb-ft)
- 3Remove lower grille push-pin retainersWorking from below the front fascia, locate the push-pin retainers along the lower edge of the grille. Remove 6 push-pin retainers by prying the center pin upward to release, then pulling the entire retainer from the grille assembly. Note their positions for reinstallation.Torque specClips5 Nm (4 lb-ft)
- 4Release grille side retention tabsAt each side edge of the grille, identify the retention tabs that engage slots in the front fascia structure. Carefully press or flex the tabs inward while applying gentle outward pressure on the grille to disengage them from their slots.
- 5Remove grille assembly from vehicleWith all fasteners and retention tabs released, carefully pull the grille assembly forward and away from the vehicle. Support the grille with both hands to prevent it from falling or contacting painted surfaces. Set the grille aside in a protected area.
- 6Inspect mounting points and hardwareExamine the radiator support mounting points, fascia slots, and all retention hardware for damage or wear. Inspect push-pin retainers for broken tabs or deformed centers. Replace any damaged hardware before installing the new grille.
- 7Position new grille assemblyAlign the new grille assembly with the front fascia opening. Ensure the side retention tabs are positioned to engage their corresponding slots and the upper mounting holes align with the radiator support threaded bosses.
- 8Engage side retention tabsPress the grille firmly into position, ensuring the side retention tabs fully engage into their slots on both sides. You should feel or hear a positive engagement when the tabs seat properly.
- 9Install upper mounting screwsFrom the engine bay, install the upper mounting screws through the grille into the radiator support. Hand-start all screws before tightening any. Tighten screws snugly and evenly in a cross pattern per factory specification, taking care not to strip the mounting bosses.Torque specGrille Mounting Screws3 Nm (2 lb-ft)
- 10Install lower push-pin retainersWorking from below, install the 6 push-pin retainers along the lower edge of the grille. Insert each retainer body into its mounting hole, then press the center pin down firmly until it clicks and locks the retainer in place. Verify each retainer is fully seated and secure.Torque specClips5 Nm (4 lb-ft)
Reassembly
- Reassembly is detailed in the removal steps above, performed in reverse order
- Ensure all retention tabs are fully engaged before installing fasteners
- Verify grille sits flush with surrounding fascia panels on all edges
Verification
- Inspect grille alignment with hood opening and front fascia, ensuring consistent gaps on all sides
- Verify all fasteners are tight and retention tabs are fully engaged
- Gently attempt to move the grille by hand to confirm it is securely mounted with no excessive play
- Close and open hood to ensure no interference with grille assembly