Every control module on the 2021-2026 Ford Edge — where it lives, replacement time, and what it takes to program a replacement. Modules marked dealer / factory tool won't work after a part swap alone — budget for programming.
Transmission Control Module (TCM) 4.5 hr R&R security gateway +1.0 hr ▸ programming details
📍 Integrated with valve body inside transmission (8F35 8-speed automatic)
🔧 Ford FDRS + J2534
⚠️ Transmission pan removal required. Security gateway authentication, adaptive learning reset, and PMI required.
Power Steering Control Module (PSCM) 2.5 hr R&R dealer / factory tool +0.5 hr ▸ programming details
📍 Integrated with electric power steering column assembly, below instrument panel
🔧 Ford FDRS + J2534
⚠️ Steering column removal required. Steering angle sensor calibration required after replacement.
Body Control Module (BCM) 2.0 hr R&R security gateway +1.2 hr ▸ programming details
📍 Behind center stack, above transmission tunnel
🔧 Ford FDRS + J2534
⚠️ Security gateway authentication required. As-built configuration critical. Controls lighting, wipers, locks, windows, PATS.
Gateway Module (GWM) 1.8 hr R&R security gateway +1.0 hr ▸ programming details
📍 Behind center stack, above transmission tunnel near BCM
🔧 Ford FDRS + J2534
⚠️ Central network hub and security gateway. As-built data critical. Controls security authentication for other modules.
Heating Ventilation Air Conditioning Module (HVAC) 1.5 hr R&R aftermarket tool +0.3 hr ▸ programming details
📍 Behind center stack, integrated with climate control head unit
🔧 Ford FDRS or Autel
⚠️ Automatic climate control. Actuator calibration required after replacement.
Transfer Case Control Module (TCCM) 1.5 hr R&R aftermarket tool +0.3 hr AWD models ▸ programming details
📍 Mounted on transfer case, passenger side of transmission tunnel
🔧 Ford FDRS or Autel
⚠️ Controls PTU (Power Transfer Unit) clutch engagement. Configuration required for drive mode settings.
Anti-Lock Brake System Module (ABS) 1.5 hr R&R dealer / factory tool +0.5 hr ▸ programming details
📍 Engine compartment, driver side inner fender near master cylinder
🔧 Ford FDRS + J2534
⚠️ Integrated hydraulic control unit. Brake bleeding required. PMI and configuration required.
Image Processing Module A (IPMA) 1.5 hr R&R dealer / factory tool +0.8 hr with lane keeping assist or adaptive cruise control ▸ programming details
📍 Behind rearview mirror, integrated with windshield camera assembly
🔧 Ford FDRS + J2534
⚠️ Forward-facing camera. Windshield calibration required after replacement or windshield replacement. Static or dynamic calibration procedure.
Accessory Protocol Interface Module (APIM) 1.2 hr R&R dealer / factory tool +0.5 hr ▸ programming details
📍 Behind center touchscreen display in center stack
🔧 Ford FDRS + J2534
⚠️ SYNC 3 or SYNC 4 system depending on year. As-built configuration required. Software updates via USB or FDRS.
Seat Control Module (SCM) 1.2 hr R&R aftermarket tool +0.2 hr with power driver seat with memory ▸ programming details
📍 Under driver seat, integrated with seat frame
🔧 Ford FDRS or Autel
⚠️ Controls power seat adjustments and memory positions. Requires seat position relearn. Standard on Titanium and ST.
Powertrain Control Module (PCM) 1.2 hr R&R security gateway +1.0 hr ▸ programming details
📍 Engine compartment, driver side firewall mounted on bracket
🔧 Ford FDRS + J2534
⚠️ Security gateway authentication required. VIN-specific calibration and PMI. PATS security link mandatory.
Door Zone Module (DZM) 1.2 hr R&R aftermarket tool +0.3 hr ▸ programming details
📍 Inside each front door, behind door panel near latch
🔧 Ford FDRS or Autel
⚠️ One per front door. Controls windows, locks, mirrors, memory seats. Window auto-up/down relearn required.
Radar Module (RADAR) 1.2 hr R&R dealer / factory tool +0.8 hr with adaptive cruise control or pre-collision assist ▸ programming details
📍 Front bumper, center behind grille emblem
🔧 Ford FDRS + J2534
⚠️ Forward radar. Aim calibration required after replacement. Static calibration procedure with targets.
Restraints Control Module (RCM) 1.0 hr R&R security gateway +0.8 hr ▸ programming details
📍 Center console, below center stack behind trim panel
🔧 Ford FDRS + J2534
⚠️ Battery disconnect and 2-minute wait mandatory. Security gateway authentication. Crash data retrieval possible before replacement.
Front Lighting Control Module (FLCM) 1.0 hr R&R aftermarket tool +0.3 hr with LED or adaptive headlights ▸ programming details
📍 Engine compartment, behind driver side headlight assembly
🔧 Ford FDRS or Autel
⚠️ Controls adaptive lighting and auto high beam. Configuration required for beam pattern.
Telematics Control Unit (TCU) 1.0 hr R&R dealer / factory tool +0.5 hr with FordPass Connect ▸ programming details
📍 Behind center stack, near APIM
🔧 Ford FDRS + J2534
⚠️ 4G LTE modem. Subscription activation required after replacement.
Liftgate Module (LGM) 1.0 hr R&R aftermarket tool +0.3 hr with power liftgate ▸ programming details
📍 Rear liftgate, driver side behind interior trim panel
🔧 Ford FDRS or Autel
⚠️ Height calibration required after replacement. Hands-free operation on equipped models.
Digital Audio Control Module C (DACMC) 1.0 hr R&R aftermarket tool +0.3 hr with premium B&O audio system ▸ programming details
📍 Behind rear cargo trim panel, driver side
🔧 Ford FDRS or Autel
⚠️ Premium audio amplifier. Configuration required for speaker setup.
Instrument Panel Cluster (IPC) 0.8 hr R&R security gateway +0.8 hr ▸ programming details
📍 Instrument panel, behind gauge cluster trim
🔧 Ford FDRS + J2534
⚠️ Security gateway authentication required. Mileage programming and as-built configuration mandatory.
Fuel Pump Control Module (FPCM) 0.8 hr R&R relearn only +0.2 hr ▸ programming details
📍 Rear cargo area, driver side behind trim panel above fuel tank
🔧 Ford FDRS or Autel
⚠️ Controls fuel pump speed. Self-learns after installation; scan tool can expedite.
Parking Aid Module (PAM) 0.8 hr R&R aftermarket tool +0.3 hr with front/rear parking sensors ▸ programming details
📍 Rear cargo area, passenger side behind trim panel
🔧 Ford FDRS or Autel
⚠️ Sensor calibration required after replacement.
Suspension Control Module (SCM) 0.8 hr R&R dealer / factory tool +0.5 hr ST models with sport-tuned suspension ▸ programming details
📍 Rear cargo area, passenger side quarter panel
🔧 Ford FDRS + J2534
⚠️ Controls continuously controlled damping on ST models. Requires ride height sensor calibration.
Trailer Brake Control Module (TBC) 0.8 hr R&R aftermarket tool +0.2 hr with factory trailer brake controller ▸ programming details
📍 Behind driver side kick panel, near fuse box
🔧 Ford FDRS or Autel
⚠️ Integrated trailer brake controller. Calibration via IPC menu after installation.
Passive Anti-Theft System Module (PATS) security gateway +0.8 hr ▸ programming details
📍 Integrated within BCM
🔧 Ford FDRS + J2534
⚠️ Function integrated in BCM. Security gateway authentication required. Key programming requires all keys present.
Aftermarket tool coverage varies by software version and vehicle build — treat "aftermarket tool" rows as "usually possible" and verify against your tool maker's coverage list before promising a customer. Spot a wrong location or hour?
Tell us — corrections ship fast here.