This procedure covers removal and replacement of the HVAC blower motor assembly located in the passenger compartment beneath the glove box area.

Warnings

Tools required

Parts

• Blower motor assembly × 1 — Motorcraft MM-1056 or equivalent
• Blower motor resistor (if damaged) × 1 — Motorcraft YH-1715 or equivalent

Preparation

1. Park vehicle on level ground and turn off ignition
2. Disconnect negative battery cable and wait 2 minutes
3. Remove any items from under the passenger side dashboard area to create workspace
4. Set HVAC controls to OFF position

Procedure

1. 1

   Remove passenger side lower dash panel
   Locate the lower dash panel beneath the glove box on the passenger side. Remove the plastic panel retaining clips using a panel removal tool. Carefully pull the lower panel downward and away from the dash to expose the blower motor housing. There are typically 3-4 push clips securing this panel.
2. 2

   Disconnect blower motor resistor connector
   Locate the blower motor resistor module mounted on the side of the blower motor housing. Depress the locking tab on the electrical connector and pull straight out to disconnect. Inspect the connector terminals for signs of overheating or corrosion.
3. 3

   Remove blower motor resistor
   Remove the two screws securing the blower motor resistor to the housing. Pull the resistor module out of the housing. Set aside and inspect for damage or burned components.
   Torque spec

   Blower Motor Resistor Screws2 Nm (1.5 lb-ft)
4. 4

   Disconnect blower motor electrical connector
   Reach behind the blower motor housing and locate the main blower motor electrical connector. Press the locking tab and pull the connector straight off the blower motor terminals. Note the connector orientation for reinstallation.
5. 5

   Remove blower motor mounting screws
   Locate the three mounting screws securing the blower motor assembly to the HVAC housing. These screws are positioned around the perimeter of the blower motor flange. Remove all three screws using an 8mm socket. Support the blower motor with one hand as you remove the final screw.
   Torque spec

   Blower Motor Screws4 Nm (3 lb-ft)
6. 6

   Remove blower motor assembly
   Carefully lower the blower motor assembly from the housing. Rotate the motor as needed to clear the housing opening. The motor and fan cage assembly is removed as a single unit. Be careful not to damage the fan blades during removal.
7. 7

   Clean blower motor housing
   Use a shop vacuum to remove any debris, leaves, or dirt from inside the blower motor housing cavity. Inspect the housing seal surface for damage or deterioration. Check the evaporator drain tube is clear of obstructions.
8. 8

   Install new blower motor assembly
   Position the new blower motor assembly into the housing opening. Align the mounting screw holes and ensure the motor sits flush against the housing flange. Verify the seal is properly positioned before installing screws.
   Torque spec

   Blower Motor Screws4 Nm (3 lb-ft)
9. 9

   Reconnect blower motor electrical connector
   Connect the main electrical connector to the blower motor terminals. Ensure the connector locks into place with an audible click. Gently tug on the connector to verify it is fully seated.
10. 10

    Install blower motor resistor
    Insert the blower motor resistor module into its mounting location on the housing. Align the screw holes and install the two retaining screws. Do not overtighten as the resistor housing is plastic.
    Torque spec

    Blower Motor Resistor Screws2 Nm (1.5 lb-ft)
11. 11

    Reconnect resistor electrical connector
    Connect the electrical connector to the blower motor resistor. Push firmly until the locking tab clicks into place. Verify the connection is secure.
12. 12

    Reinstall lower dash panel
    Position the lower dash panel back into place. Align the push clips with their mounting holes and firmly press until each clip locks into position. Verify the panel is secure and properly aligned.

Reassembly

1. Reconnect the negative battery cable
2. Verify all electrical connectors are properly seated and locked
3. Ensure no tools or parts are left in the work area

Verification

• Turn the ignition to the ON position without starting the engine
• Test blower motor operation at all fan speed settings (1-7) to ensure proper function
• Listen for unusual noises such as squealing, grinding, or rubbing during operation
• Verify airflow is coming from all vent positions when selected
• Check that the lower dash panel is properly secured with no rattles or loose clips
• Confirm no warning lights related to climate control appear on the instrument cluster

More procedures for this vehicle