Free API
🌍 International coverage, work in progress. This Russian-market vehicle is part of our hand-curated international catalog. We are filling in labor times, torque specs and fluids as fast as we can verify them, so some numbers may be missing or marked estimated for now. Do you work on these vehicles in the EU, Russia, or the JDM scene? Help us get it right: send real shop times or corrections to [email protected], or request the data you need and it joins the verification queue.

2026 FORD KUGA PL

1.5L I3 EcoBoost 150•FWD•AUTOMATIC•gas•turbo
Be the first sponsor for this vehicle

For $99, we generate the full set of step-by-step repair procedures for this exact vehicle. Free for everyone, forever, with your name on every one.

Sponsor — $99
Dead battery / stuck in Park? Emergency neutral procedure for this Kuga PL →

Control Modules — 2026 Ford Kuga PL

Every control module on the 2020-2026 Ford Kuga PL — where it lives, replacement time, and what it takes to program a replacement. Modules marked dealer / factory tool won't work after a part swap alone — budget for programming.
Transmission Control Module (TCM)4.5 hr R&Rdealer / factory tool +1.0 hr▸ programming details
📍 Integrated with valve body inside transmission (mechatronic unit)
🔧 Ford FDRS + J2534
⚠️ Mechatronic unit replacement requires transmission fluid drain, pan removal, and adaptive learning drive cycle. PMI required.
Battery Energy Control Module (BECM)2.5 hr R&Rdealer / factory tool +1.0 hrPHEV models only▸ programming details
📍 Under rear cargo floor, mounted to high-voltage battery pack
🔧 Ford FDRS + J2534
⚠️ High-voltage system. Requires HV safety procedures and isolation. Battery pack removal may be required. PMI mandatory.
Power Steering Control Module (PSCM)2.2 hr R&Rdealer / factory tool +0.6 hr▸ programming details
📍 Integrated with electric power steering motor on steering column
🔧 Ford FDRS + J2534
⚠️ Steering angle sensor calibration required after replacement. Module and motor sold as assembly.
Anti-Lock Brake System Module (ABS)1.8 hr R&Rdealer / factory tool +0.5 hr▸ programming details
📍 Engine compartment, mounted to hydraulic control unit on left inner fender
🔧 Ford FDRS + J2534
⚠️ Brake bleeding required after replacement. Module integrated with hydraulic unit; sold as assembly.
Heating Ventilation Air Conditioning Module (HVAC)1.8 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Behind center stack, integrated with climate control head unit
🔧 Autel/Launch or FDRS
⚠️ Automatic climate control calibration and actuator relearn required.
Transfer Case Control Module (TCCM)1.5 hr R&Raftermarket tool +0.3 hrAWD models (standard)▸ programming details
📍 Mounted to transfer case on right side
🔧 Autel/Launch or FDRS
⚠️ Controls AWD coupling and torque distribution. Relearn drive cycle required after replacement.
Body Control Module (BCM)1.5 hr R&Rdealer / factory tool +1.2 hr▸ programming details
📍 Behind left side of instrument panel, above fuse box
🔧 Ford FDRS + J2534
⚠️ Stores as-built configuration for all body functions. All options must be reconfigured after replacement. Key programming required.
Fuel Pump Control Module (FPCM)1.5 hr R&Rrelearn only +0.2 hr▸ programming details
📍 Under vehicle, mounted to fuel tank
🔧 Scan tool auto-relearn
⚠️ Controls fuel pump speed via PWM. Auto-relearn on key cycle. Tank lowering may be required for access.
Active Park Assist Module (APAM)1.3 hr R&Rdealer / factory tool +0.6 hrwith Active Park Assist 2.0▸ programming details
📍 Behind center console, under front seats
🔧 Ford FDRS + J2534
⚠️ Controls automated parking. Integrates with PAM, IPMB, and PSCM. Calibration required.
Door Zone Module (DZM)1.2 hr R&Raftermarket tool +0.3 hrwith power windows/locks (standard)▸ programming details
📍 Inside each front door, behind door panel
🔧 Autel/Launch or FDRS
⚠️ One module per front door. Controls windows, locks, mirrors. Window auto-up/down relearn required.
Radar Module (RADAR)1.2 hr R&Rdealer / factory tool +0.8 hrwith adaptive cruise control▸ programming details
📍 Behind front grille, center lower position
🔧 Ford FDRS + J2534
⚠️ Forward radar for ACC and pre-collision. Radar aim calibration required after replacement. Grille removal necessary.
Powertrain Control Module (PCM)1.2 hr R&Rdealer / factory tool +0.8 hr▸ programming details
📍 Engine compartment, left side firewall mounted below brake master cylinder
🔧 Ford FDRS + J2534
⚠️ Requires VIN-specific calibration download and PMI procedure. Security gateway authentication required 2020+.
Audio Control Module / Accessory Protocol Interface Module (ACM/APIM)1.2 hr R&Rdealer / factory tool +0.8 hr▸ programming details
📍 Behind center touchscreen display in instrument panel
🔧 Ford FDRS + J2534
⚠️ SYNC system configuration and as-built data required. Navigation/SYNC version dependent on hardware.
Parking Aid Module (PAM)1.0 hr R&Raftermarket tool +0.3 hrwith parking sensors▸ programming details
📍 Behind rear bumper cover, center mounted
🔧 Autel/Launch or FDRS
⚠️ Processes ultrasonic sensor inputs. Sensor calibration may be required after replacement.
Gateway Module (GWM)1.0 hr R&Rsecurity gateway +1.0 hr▸ programming details
📍 Behind left side of instrument panel, near BCM
🔧 Ford FDRS + J2534
⚠️ Security gateway for CAN network. Requires Ford authentication for programming. All module access routed through GWM.
Liftgate Module (LGM)1.0 hr R&Raftermarket tool +0.3 hrwith power liftgate▸ programming details
📍 Inside liftgate, behind trim panel left side
🔧 Autel/Launch or FDRS
⚠️ Liftgate height memory and pinch protection calibration required after replacement.
Instrument Panel Cluster (IPC)0.9 hr R&Rdealer / factory tool +0.5 hr▸ programming details
📍 Instrument panel, behind gauge cluster trim
🔧 Ford FDRS + J2534
⚠️ Mileage programming required by law. As-built configuration for display options mandatory.
Trailer Brake Control Module (TBC)0.9 hr R&Raftermarket tool +0.2 hrwith factory trailer tow package▸ programming details
📍 Behind left rear quarter trim panel
🔧 Autel/Launch or FDRS
⚠️ Integrated trailer brake controller. Gain settings stored in module.
Restraints Control Module (RCM)0.8 hr R&Rdealer / factory tool +0.4 hr▸ programming details
📍 Center console, below center stack behind trim panel
🔧 Ford FDRS + J2534
⚠️ Battery disconnect required. Crash data must be cleared. PMI procedure mandatory.
Image Processing Module (IPMB)0.8 hr R&Rdealer / factory tool +0.5 hrwith lane keeping/pre-collision assist▸ programming details
📍 Behind rearview mirror assembly in headliner
🔧 Ford FDRS + J2534
⚠️ Forward-facing camera for ADAS. Windshield camera calibration mandatory after replacement or windshield work.
Front Lighting Control Module (FLCM)0.8 hr R&Raftermarket tool +0.3 hrwith LED or adaptive headlights▸ programming details
📍 Behind left headlight assembly in engine compartment
🔧 Autel/Launch or FDRS
⚠️ Controls adaptive lighting and LED functions. Headlight aim calibration required after replacement.
Telematics Control Unit (TCU)0.6 hr R&Rdealer / factory tool +0.5 hrwith FordPass Connect▸ programming details
📍 Behind headliner above rearview mirror
🔧 Ford FDRS + J2534
⚠️ Cellular modem for FordPass services. Subscription activation required after replacement.
Passive Anti-Theft System Module (PATS)dealer / factory tool +0.5 hr▸ programming details
📍 Integrated within BCM
🔧 Ford FDRS + J2534
⚠️ Function integrated in BCM. Key programming and immobilizer configuration performed through BCM.
Aftermarket tool coverage varies by software version and vehicle build — treat "aftermarket tool" rows as "usually possible" and verify against your tool maker's coverage list before promising a customer. Spot a wrong location or hour? Tell us — corrections ship fast here.
🔧 Built by master technician Chris Hackleman · Master Technician · 20+ years.
Stuck on a repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
Building an app?
Free API access to all this data — 10 requests/day, no card required.
Get an API key →
Run a shop?
Manage repairs, estimates, and customers with ShopBase — $249/mo, all features included. Built by the same team.
Try ShopBase →