Air Suspension Height Sensor

This procedure addresses replacement of the air suspension height sensor on a 2018-2024 Honda Accord 1.5L Turbo. Note: The standard Honda Accord does not come equipped with air suspension; this procedure applies only to vehicles with aftermarket air suspension systems.

Warnings

Tools required

Parts

• Air suspension height sensor × 1 — Use OEM specification or aftermarket suspension manufacturer part number
• Sensor mounting hardware kit (if damaged) × 1 — Use OEM specification

Preparation

1. Park vehicle on level ground and engage parking brake.
2. Disconnect negative battery terminal and wait 3 minutes before proceeding.
3. If equipped, disable air suspension system via control module or switch to prevent automatic leveling during service.
4. Raise vehicle and secure on jack stands at manufacturer-specified jacking points.
5. Remove wheel on the side where height sensor is being replaced.

Procedure

1. 1

   Locate the height sensor
   Identify the height sensor location on your specific aftermarket air suspension system. Common mounting points are on the lower control arm with linkage to chassis, or directly on the air strut assembly. The sensor will have an electrical connector and a pivot linkage arm.
2. 2

   Disconnect sensor electrical connector
   Locate the electrical connector on the height sensor wiring harness. Press the release tab and carefully disconnect the connector. Inspect connector pins for corrosion or damage. If connector is dirty, clean with electrical contact cleaner and allow to dry completely.
3. 3

   Document sensor linkage position
   Before removing the sensor, note or photograph the exact position and angle of the sensor linkage arm relative to the suspension components. This ensures correct calibration upon reinstallation. Measure the distance from the sensor mounting point to the linkage connection point if possible.
4. 4

   Disconnect sensor linkage arm
   Remove the linkage arm connecting the height sensor to the control arm or chassis. This typically involves removing a small clip or nut securing the ball joint end of the linkage. Use a flathead screwdriver to release any retaining clips. Keep all hardware for reinstallation.
5. 5

   Remove height sensor mounting bolts
   Remove the bolts securing the height sensor to its mounting bracket on the control arm, strut, or chassis. Most aftermarket sensors use 10mm or 12mm mounting bolts. Support the sensor while removing the final bolt to prevent it from falling.
6. 6

   Remove old height sensor
   Carefully remove the height sensor from the vehicle. Inspect the mounting bracket for damage, cracks, or excessive corrosion. Clean the mounting surface with a wire brush if necessary. Verify the new sensor matches the old unit in terms of connector type and mounting configuration.
7. 7

   Install new height sensor
   Position the new height sensor on the mounting bracket, aligning the bolt holes. Install the mounting bolts and hand-tighten initially. Ensure the sensor is oriented correctly with the linkage pivot point facing the proper direction as documented earlier.
8. 8

   Torque sensor mounting bolts
   Using a torque wrench, tighten the height sensor mounting bolts to specification. Verify the sensor is secure and does not rotate on the mounting bracket. Check that the sensor has full range of motion without interference from suspension components.
9. 9

   Reconnect sensor linkage arm
   Attach the linkage arm to the control arm or chassis connection point, matching the position documented in step 3. Install the retaining clip or nut and ensure the linkage pivots freely without binding. The linkage should move smoothly through its full range as the suspension cycles.
10. 10

    Connect electrical connector
    Reconnect the electrical connector to the height sensor, ensuring it clicks securely into place. Gently tug on the connector to verify it is fully seated. Route the wiring away from moving suspension components and heat sources.
11. 11

    Reinstall wheel and lower vehicle
    Reinstall the wheel and hand-tighten lug nuts in a star pattern. Lower the vehicle until the tire just contacts the ground. Torque the lug nuts to specification in a star pattern. Fully lower the vehicle and remove jack stands.
12. 12

    Reconnect battery and initialize system
    Reconnect the negative battery terminal. Turn the ignition to ON position (engine off) and allow the air suspension control module to initialize. Follow the specific calibration procedure for your aftermarket air suspension system, which may involve cycling the suspension through its full range or using a dedicated scan tool.

Reassembly

1. Ensure all electrical connectors are fully seated and secured away from moving components.
2. Verify height sensor linkage moves freely through full suspension travel without binding or interference.
3. Check that all mounting bolts are torqued to specification and properly secured.
4. Confirm no tools or parts were left in the wheel well or suspension area.

Verification

• Start the engine and verify no suspension warning lights appear on the instrument cluster.
• If equipped with air suspension controls, cycle through different ride height settings and confirm the system responds correctly.
• Perform a visual inspection with vehicle at normal ride height to ensure the sensor linkage is at approximately mid-range position.
• Test drive the vehicle and monitor suspension response. The system should automatically level the vehicle under load changes.
• Use a scan tool compatible with your aftermarket air suspension system to verify the height sensor is reporting correct values and no fault codes are present.
• Verify the sensor reads changing values as the suspension is manually compressed and extended (with vehicle safely supported).

Related trouble codes on this vehicle

Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.

Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →

More procedures for this vehicle