Washer Reservoir

Remove and replace the windshield washer fluid reservoir on a 2018-2024 Honda Accord 1.5L Turbo, including pump and hose connections.

Warnings

Tools required

Parts

• Windshield washer reservoir × 1 — 76841-TVA-A01 or equivalent
• Washer pump grommet (if damaged) × 1 — Use OEM specification
• Reservoir mounting grommet (if damaged) × 1 — Use OEM specification

Fluids

• Windshield Washer Fluid — 3.5 qt

Preparation

1. Park vehicle on level surface and engage parking brake
2. Turn ignition off and remove key
3. Open hood and secure with prop rod
4. Allow engine to cool if recently operated

Procedure

1. 1

   Drain washer fluid
   Place drain pan under the driver side front wheel well area. Use the windshield washer function to pump out as much fluid as possible from the reservoir. This reduces spillage during removal.
2. 2

   Remove driver side front wheel well liner (partial)
   Turn the steering wheel fully to the right for access. Remove the plastic clips securing the front portion of the driver side wheel well liner using a trim tool or flathead screwdriver. You only need to pull back the front section to access the reservoir - full removal is not necessary.
3. 3

   Access reservoir from wheel well
   Pull back the wheel well liner to expose the lower portion of the washer reservoir. The reservoir is located behind the front bumper on the driver side. Identify the washer pump electrical connector and fluid hoses.
4. 4

   Disconnect washer pump electrical connector
   Press the locking tab on the washer pump electrical connector and pull straight out to disconnect. The connector is on the bottom of the pump motor which is inserted into the reservoir.
5. 5

   Disconnect washer hoses
   Squeeze the hose clamp tabs or use pliers to slide clamps back on both the outlet hose (to hood nozzles) and the filler neck hose. Pull hoses straight off the reservoir fittings. Have drain pan positioned to catch residual fluid. Note hose routing for reinstallation.
6. 6

   Remove reservoir mounting fasteners
   Locate the reservoir mounting bolts - typically one or two 10mm bolts securing the reservoir to the inner fender/frame. Remove these bolts completely using a 10mm socket with extension.
7. 7

   Remove washer reservoir
   Carefully maneuver the reservoir down and out through the wheel well opening. Tilt and rotate as needed to clear the bumper structure and fender. The reservoir may have additional grommets or clips at mounting points that need to be released.
8. 8

   Remove washer pump from old reservoir (if reusing)
   If reusing the washer pump, twist and pull the pump motor out of the reservoir grommet. Inspect the rubber grommet seal - replace if cracked or damaged. Clean the pump screen if debris is present.
9. 9

   Install pump into new reservoir
   Insert the washer pump into the new reservoir grommet with a twisting motion until it seats fully. Ensure the rubber grommet creates a complete seal around the pump body to prevent leaks. The pump should be firmly seated and not easily pulled out.
10. 10

    Position new reservoir
    Guide the new reservoir up into position through the wheel well opening. Align mounting holes with frame brackets. Ensure no hoses or wires are pinched during installation.
11. 11

    Install mounting fasteners
    Install the reservoir mounting bolts and tighten to secure the reservoir to the frame. Hand-tighten first to ensure proper alignment, then torque to specification.
    Torque spec

    Module Mounting Bolts8 Nm (6 lb-ft)
12. 12

    Reconnect hoses and electrical
    Connect the outlet hose and filler neck hose to the reservoir, sliding hose clamps into position to secure. Ensure hoses are routed properly and not kinked. Connect the electrical connector to the washer pump until it clicks into place.
13. 13

    Reinstall wheel well liner
    Position the wheel well liner back into place and install all plastic retaining clips. Ensure liner is properly seated and will not contact the tire during operation.
14. 14

    Fill reservoir and test system
    Fill the washer reservoir with fresh windshield washer fluid to the full mark (approximately 3.5 quarts capacity). Start the vehicle and test the washer system operation. Check for leaks at all connections, hoses, and pump grommet. Verify both windshield washer nozzles spray properly.

Reassembly

1. Torque all mounting bolts to specification - avoid over-tightening plastic reservoir mounting points
2. Ensure all hose clamps are properly positioned and secure to prevent air leaks
3. Verify electrical connector is fully seated with audible click
4. Check that wheel well liner is secure and will not rub on tire

Verification

• Fill reservoir to full line and verify no leaks at pump, hoses, or connections
• Activate washer system and confirm strong spray pattern from both nozzles
• Check that pump operates quietly without unusual noise indicating air in system
• Inspect wheel well area for any fluid drips after test operation
• Turn steering wheel lock-to-lock and verify wheel well liner does not contact tire

Related trouble codes on this vehicle

Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.

Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →

More procedures for this vehicle