1990 HONDA CIVIC

Typical onset: 80,000-150,000 mi

Symptoms: Slipping between gears, especially 2nd to 3rd, Delayed engagement when shifting from Park to Drive, Shuddering or jerking during acceleration, Dark, burnt-smelling transmission fluid

Fix: Rebuild or replacement required. Rebuild takes 8-12 hours; used transmission swap is 4-6 hours but availability is declining. Many owners convert to manual at this point. Recalls covered cooler issues but not internal wear.

Estimated cost: $1,200-2,500

Typical onset: 120,000-180,000 mi

Symptoms: White smoke from exhaust, especially at startup, Coolant loss with no visible leaks, Milky oil on dipstick or cap, Overheating in traffic or on hills

Fix: Head gasket replacement is 6-8 hours. Critical: resurface head to spec (common warping on D15B/D15B2). If overheated severely, expect crankshaft or bearing damage requiring short block replacement (15-20 hours). Most Civics this age have had this done or need it soon.

Estimated cost: $800-1,400 (gasket only); $2,000-3,500 (short block)

Symptoms: No-start when engine is hot, starts fine when cool, Fuel pump doesn't prime (no hum for 2 seconds at key-on), Intermittent stalling after driving 20-30 minutes, Dashboard lights work but engine cranks without firing

Fix: Main relay (PGM-FI relay) under dash has cold solder joints that crack with heat cycles. Remove relay (15 minutes), resolder joints with 60/40 solder (30 minutes), reinstall. DIY fix costs nothing; shops charge 0.5-1.0 hour if customer brings relay. Common enough that experienced techs diagnose it in 5 minutes.

Estimated cost: $0-80

Typical onset: 100,000+ mi

Symptoms: Oil weeping around distributor base, Intermittent stalling or rough idle when wet, Check Engine Light with ignition-related codes, Hard starting in damp weather

Fix: Distributor shaft seal and O-ring deteriorate, letting oil into distributor. Replace O-ring and seal (1.5 hours), inspect distributor internals for oil contamination. If igniter or pickup coil oil-soaked, replace distributor assembly (2 hours). Prevent by changing seal every 60k.

Estimated cost: $120-250 (seal only); $300-500 (full distributor)

Typical onset: 150,000+ mi

Symptoms: Ticking or hissing from engine bay on cold start, Exhaust smell in cabin with heater on, Visible cracks or rust perforation at manifold/cat junction, Failed emissions test (if applicable)

Fix: Cast manifold cracks near cat converter from heat cycles. Aftermarket header install is 2-3 hours; OEM manifold if available is 3-4 hours due to rusted studs. Expect to drill out at least two studs. Not a breakdown issue but gets loud and annoying.

Estimated cost: $250-600

Typical onset: 80,000-120,000 mi

Symptoms: Clunking when shifting from Reverse to Drive, Excessive engine movement visible from engine bay, Vibration through shifter and steering wheel at idle, Acceleration feels sluggish due to drivetrain slop

Fix: Rubber mounts turn to mush. Front mount (1.5 hours), rear mount (1 hour), side mount (1 hour). Do all three at once for best results — labor overlaps. Cheap parts, huge difference in feel. Transmission mount particularly critical on automatics.

Estimated cost: $250-450 (all mounts)

Symptoms: Bubbling paint behind rear wheels, Holes visible in rocker panels or quarter panels, Strut tower mushrooming (severe cases), Trunk floor rust-through near taillights

Fix: Thin sheet metal and poor rust protection from factory. Rear wheel wells rot from inside out (mud traps). Rockers rust through in 10-15 years in salt states. Strut tower issues are frame damage — walk away. Cosmetic rocker repair is 6-10 hours per side for proper metalwork. Preventive: spray Fluid Film in wheel wells and rocker pinch welds annually.

Estimated cost: $800-2,000 per side (rockers); $4,000+ (quarters)