transmission
Clutch Kit
for 1993 Honda Civic 1.5L I4 D15 · FWD
🔓 Unlocked for everyone by Michael Bogus · 2026-11-02
Difficulty
Advanced
Time
6.5 h
Tools
14
Steps
15
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.
Remove and replace the clutch kit (clutch disc, pressure plate, and release bearing) on a 1993 Honda Civic with 1.5L D15 engine, requiring transaxle removal.
Warnings
⚠️Vehicle must be securely supported on jack stands rated for the vehicle weight. Never work under a vehicle supported only by a floor jack.
⚠The transaxle weighs approximately 75-85 lbs. Use a transmission jack or have an assistant help support it during removal and installation.
⚠Do not allow the clutch disc to contact oil, grease, or brake cleaner. Handle only by the edges.
ℹ️The front axle nuts are staked and may require replacement. Verify local procedure before removing.
Tools required
Floor jack and jack standsEssential
Socket set (8mm-19mm)Essential
Breaker barEssential
Torque wrenchEssential
Pry barEssential
Clutch alignment toolEssential
12mm combination wrenchEssential
14mm combination wrenchEssential
17mm combination wrenchEssential
As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.
Parts
- Clutch kit (disc, pressure plate, release bearing) × 1 — Use OEM specification or quality aftermarket equivalent
- Transmission fluid × 1 — Honda MTF or equivalent GL-4 manual transmission fluid
- Front axle nut (optional, if reusing is not permitted) × 2 — Use OEM specification
As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.
Preparation
- Park vehicle on level ground and engage parking brake
- Disconnect negative battery cable
- Raise front of vehicle and support securely on jack stands under the front subframe
- Remove both front wheels
- Drain transmission fluid into suitable container by removing drain plug
Procedure
- 1Remove front axle nuts and disconnect axlesUnstake the front axle nuts using a chisel or punch. Remove the 32mm axle nuts from both sides using a breaker bar while the vehicle is still on the ground if possible, or have an assistant apply brakes. Remove the front axles: separate the lower ball joint from the knuckle by removing the ball joint castle nut and cotter pin, then separate the ball joint using a ball joint separator (verify exact method in FSM), separate the ball joint from the knuckle, and pull the axle from the hub. Carefully pry the inner CV joints from the transaxle using a pry bar between the CV joint and transaxle case. Support axles out of the way with wire.
- 2Disconnect shift linkage and clutch cableRemove the shift linkage from the transaxle by removing the 10mm bolt securing the shift rod and the pin clip securing the selector rod. Disconnect the hydraulic clutch slave cylinder from the transaxle by removing its 2 mounting bolts and setting it aside with the hydraulic line still attached (do not disconnect the line, to avoid bleeding the system).
- 3Disconnect electrical connections and speedometer cableDisconnect the reverse light switch connector from the transaxle. Remove the speedometer cable by unscrewing the retaining collar (use a 17mm wrench or by hand) from the transaxle housing.
- 4Remove starter motorDisconnect the electrical connections from the starter motor (battery cable and signal wire). Remove the 2 starter mounting bolts (14mm or 17mm) and remove the starter motor from the transaxle bellhousing. Set aside safely.
- 5Support engine and remove transaxle mountsPlace a floor jack with a block of wood under the engine oil pan to support the engine weight. Remove the transaxle mount: remove the 2-3 bolts securing the mount bracket to the transaxle, then remove the through-bolt and nuts securing the mount to the chassis. Remove the rear mount bracket bolts from the transaxle if present.
- 6Remove transaxle-to-engine boltsPosition a transmission jack or suitable support under the transaxle. Remove all transaxle-to-engine mounting bolts. These typically include 2 upper 17mm bolts accessible from the top, and 2-3 lower bolts accessible from underneath (17mm). Ensure all bolts are removed before attempting to separate the transaxle.
- 7Remove transaxle from vehicleWith all bolts removed and the transaxle supported, carefully pull the transaxle straight back away from the engine to disengage the input shaft from the clutch disc and pilot bearing. Do not allow the weight of the transaxle to hang on the input shaft. Once clear, lower the transaxle and remove it from under the vehicle. The transaxle must move straight back to avoid damaging the clutch disc.
- 8Inspect and remove pressure plate and clutch discInspect the flywheel surface for heat checking, cracks, or scoring. If damaged, flywheel resurfacing or replacement is required. Mark the pressure plate position relative to the flywheel with paint or a marker for reference. Gradually loosen the 6 pressure plate bolts in a crisscross pattern, loosening each bolt 1-2 turns at a time to prevent warping the pressure plate. Once all bolts are loose, remove them completely and remove the pressure plate and clutch disc.
- 9Remove release bearing and inspect componentsRemove the release bearing from the input shaft sleeve by sliding it off or releasing its retaining clips. Inspect the release fork for cracks or wear. Inspect the input shaft bearing retainer for smooth operation. Clean the flywheel surface with a wire brush and brake cleaner (do not use oil-based cleaner). Check the pilot bearing in the center of the crankshaft for smooth rotation; replace if rough or dry.
- 10Install new release bearingInstall the new release bearing from the clutch kit onto the input shaft sleeve. Ensure it slides freely and engages properly with the release fork. Apply a small amount of high-temperature grease to the release fork contact points and the input shaft splines (do not over-grease).
- 11Install new clutch disc and pressure platePlace the new clutch disc onto the flywheel with the spring-cushioned side (or side marked 'flywheel side' or 'transmission side') facing the correct direction (typically the larger protruding hub faces the transmission). Insert the clutch alignment tool through the clutch disc and into the pilot bearing to center the disc. Position the new pressure plate onto the flywheel, aligning the previously made marks or evenly spacing the dowel holes. Start all 6 pressure plate bolts by hand. Tighten the bolts gradually in a crisscross pattern to the specified torque (verify against FSM — approximately 19 ft-lbs for the M8 pressure plate bolts), going around multiple times to ensure even clamping. Remove the alignment tool once all bolts are fully torqued.
- 12Reinstall transaxleApply a thin coat of high-temperature grease to the input shaft splines. Carefully lift the transaxle into position and align the input shaft with the clutch disc and pilot bearing. Push the transaxle straight toward the engine, ensuring the input shaft enters the clutch disc smoothly. If resistance is felt, do not force it; pull back and realign. Once the transaxle is flush with the engine, install all transaxle-to-engine bolts and tighten in a crisscross pattern to specified torque (verify against FSM — approximately 47 ft-lbs for the larger bellhousing bolts). Note: Once the transaxle is flush with the engine, install all transaxle-to-engine bolts and tighten in a crisscross pattern to the factory-specified torque (approximately 47 ft-lbs / 64 Nm — verify against service manual for your specific bolt sizes).
- 13Reinstall mounts, starter, and connectionsReinstall the transaxle mount and brackets, tightening all fasteners to specification. Reinstall the starter motor and tighten the mounting bolts, then reconnect the electrical connections. Reconnect the speedometer cable and reverse light switch connector. Reconnect the shift linkage and adjust as necessary. Reinstall the clutch slave cylinder and tighten its mounting bolts to specification; verify hydraulic clutch operation and bleed the system if the line was disturbed.
- 14Reinstall axles and front wheelsInstall new circlips on the inner CV joint stub shafts if removed. Push the inner CV joints into the transaxle until they click into place; pull outward to verify engagement. Insert the outer CV joint stub shafts into the wheel hubs. Reconnect the lower ball joints to the steering knuckles and install the pinch bolts, tightening to specification. Install new front axle nuts and tighten to specification (134 ft-lbs), then stake the nuts. Reinstall the front wheels and torque lug nuts to specification (80 ft-lbs).
- 15Refill transmission fluid and final checksRefill the transaxle with GL-4 manual transmission fluid (or current Honda MTF equivalent) — approximately 1.9 quarts, filling until fluid reaches the bottom of the fill hole (verify capacity against FSM). Reinstall the fill plug. Reconnect the negative battery cable. Lower the vehicle from jack stands.
Reassembly
- Ensure all fasteners are tightened to specified torque values
- Verify clutch cable free-play is adjusted to 10-15mm at the pedal
- Verify shift linkage operates smoothly through all gears
- Double-check that all electrical connections and cables are reconnected
Verification
- Start the engine and verify no abnormal noises from the transaxle or clutch area
- With the engine running and parking brake engaged, depress the clutch pedal and shift through all gears to verify smooth engagement
- Test drive the vehicle to verify proper clutch engagement and disengagement, smooth shifting, and no slippage under load
- Check for any fluid leaks around the transaxle and axle seals after test drive
- Verify clutch pedal feel and engagement point are normal