steering

Power Steering Reservoir

for 2017 Maserati Levante 3.0L V6 Twin Turbo · AWD

Difficulty

Easy

Time

1.2 h

Tools

Steps

✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

This procedure covers the removal and replacement of the power steering reservoir on a 2017 Maserati Levante 3.0L V6 Twin Turbo with electric power steering (no hydraulic fluid system).

Warnings

ℹ️The 2017 Maserati Levante 3.0L V6 Twin Turbo RWD is equipped with Electric Power Steering (EPS) and does not use hydraulic power steering fluid. Verify your specific vehicle configuration before proceeding, as some markets or configurations may differ.

⚠If your vehicle has a hydraulic power steering system (non-EPS), fluid will drain when lines are disconnected. Have a drain pan ready and dispose of fluid properly.

⚠Ensure engine is cool before working in the engine compartment to avoid burn injuries from hot components.

Tools required

10mm socket and ratchetEssential

13mm socket and ratchetEssential

Torque wrench (10-50 Nm range)Essential

Trim panel removal tools

Shop towelsEssential

Drain panEssential

Pick tool or small flathead screwdriver

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

Power steering reservoir (if equipped) × 1 — Use OEM specification
Reservoir mounting grommets × 2 — Use OEM specification

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Preparation

Park vehicle on level ground and apply parking brake
Turn ignition off and remove key from vehicle
Allow engine to cool completely if recently operated
Open hood and secure with prop rod
Disconnect negative battery terminal and wait 2 minutes for system capacitors to discharge
Identify reservoir location on driver side of engine bay near firewall (if equipped with hydraulic system)
Place drain pan beneath work area to catch any residual fluid

Procedure

1
Verify power steering system type
Confirm whether your specific vehicle is equipped with electric power steering (EPS) or hydraulic power steering. The standard 2017 Levante 3.0L V6 RWD uses EPS with no reservoir. If EPS is confirmed, no reservoir service is required. If a hydraulic reservoir is present, proceed with the following steps.
2
Remove engine cover
Remove the plastic engine cover by lifting upward on the front edge to disengage the mounting grommets. Set cover aside in a clean area.
3
Disconnect reservoir hoses
Using a pick tool or small flathead screwdriver, carefully release the hose clamps securing the supply and return hoses to the reservoir. Slide clamps back along hoses. Twist and pull hoses off reservoir nipples. Allow any fluid to drain into the pan below. Plug hose ends with clean shop towels to prevent contamination.
⚠Power steering fluid may be hot if engine was recently running. Wear appropriate gloves to prevent burns.
4
Disconnect fluid level sensor connector
Locate the electrical connector on the reservoir cap or body. Press the release tab and carefully disconnect the wiring harness from the fluid level sensor. Move wiring harness aside to provide clearance.
5
Remove reservoir mounting fasteners
Remove the mounting bolts securing the reservoir bracket to the chassis or engine bay mounting points. Typical installations use two or three mounting bolts. Note the orientation and any spacers or washers for reinstallation.
Torque spec
Mounting Bolts28 Nm (21 lb-ft)
6
Remove reservoir assembly
Lift the reservoir assembly upward and out of the engine bay. Tilt as needed to clear surrounding components. Inspect mounting grommets and replace if torn, cracked, or deteriorated.
7
Prepare new reservoir
Transfer any reusable components from old reservoir to new unit if applicable (sensors, caps). Install new mounting grommets onto the reservoir body. Ensure reservoir cap is properly seated and sensor connector is clean and undamaged.
8
Install new reservoir
Position new reservoir into mounting location, ensuring grommets are properly seated in mounting brackets. Align mounting holes and install mounting bolts hand-tight initially. Verify reservoir is correctly oriented with filler neck accessible and hose connections pointing toward their respective lines.
9
Torque mounting fasteners
Using a torque wrench, tighten the reservoir mounting bolts to specification in a cross pattern if multiple bolts are present. Verify reservoir is secure and does not move when pulled gently.
Torque spec
Mounting Bolts28 Nm (21 lb-ft)
10
Reconnect hoses and electrical connector
Clean reservoir nipples and hose ends. Push supply and return hoses firmly onto reservoir nipples until fully seated. Slide hose clamps into position approximately 10mm from end of hose and secure. Reconnect fluid level sensor electrical connector until it clicks into place.
11
Refill and bleed system (if hydraulic)
If equipped with hydraulic power steering, fill reservoir to MAX mark with appropriate power steering fluid. Start engine and turn steering wheel lock-to-lock several times slowly. Check fluid level and top off as needed. Inspect all connections for leaks while engine is running.
ℹ️This step applies only to hydraulic power steering systems. EPS systems require no fluid service.
12
Reinstall engine cover and reconnect battery
Align engine cover mounting grommets with their posts and press down firmly to secure. Reconnect negative battery terminal. Start vehicle and verify no warning lights related to power steering system.

Reassembly

Ensure all hose clamps are properly positioned and tightened
Verify electrical connector is fully seated with audible click
Double-check all mounting bolts are torqued to specification
Confirm no fluid leaks are present around connections
Ensure engine cover is properly seated on all mounting points

Verification

Start engine and verify no power steering warning lights illuminate on dashboard
Turn steering wheel lock-to-lock while stationary and listen for unusual noises
Check reservoir fluid level (if hydraulic system) and verify it remains at proper level after operation
Inspect all hose connections and fittings for signs of fluid leakage
Test drive vehicle and confirm normal power steering assist operation through full range of steering inputs
Verify fluid level sensor connector is secure and no electrical warnings are present