maintenance

Tire Rotation

for 2017 Maserati Levante 3.0L V6 Twin Turbo · AWD

Difficulty

Easy

Time

30 min

Tools

Steps

✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

Rotate tires on a 2017 Maserati Levante to ensure even tire wear and maximize tire lifespan following the manufacturer's recommended rotation pattern.

Warnings

⚠️Never work under a vehicle supported only by a jack. Always use jack stands rated for the vehicle weight.

⚠The Levante equipped with staggered wheel setups (different front/rear tire sizes) cannot follow standard rotation patterns. Verify tire sizes match before proceeding.

⚠Directional tires must remain on the same side of the vehicle during rotation.

ℹ️This procedure assumes the vehicle has matching tire sizes front and rear with alloy wheels.

Tools required

Hydraulic floor jackEssential

Jack stands (4)Essential

Torque wrench (capable of 130 Nm / 96 lb-ft)Essential

Lug wrench or 21mm socketEssential

Wheel chocksEssential

Tire pressure gauge

Tire chalk or marker

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Preparation

Park vehicle on a level, paved surface and engage parking brake
If equipped with matching tire sizes, mark each tire position (LF, RF, LR, RR) with chalk before starting
Verify all tires are cold and note current tire pressures for reference
Place wheel chocks behind the rear wheels before lifting
Loosen all lug nuts 1/4 turn while vehicle is still on the ground (do not remove)
Consult owner's manual to confirm tire sizes are not staggered

Procedure

1
Lift front of vehicle
Position hydraulic jack under the front jacking point located behind the front bumper at the center subframe. Lift the front of the vehicle and place jack stands under the front pinch weld reinforced jacking points on each side. Lower vehicle onto jack stands.
2
Lift rear of vehicle
Position hydraulic jack under the rear differential or rear subframe jacking point. Lift the rear of the vehicle and place jack stands under the rear pinch weld reinforced jacking points on each side. Lower vehicle onto jack stands. Ensure all four corners are securely supported.
3
Remove all four wheels
Finish removing the lug nuts that were previously loosened (remove in a star pattern). Carefully remove all four wheels and place them in a safe location corresponding to their marked positions.
4
Inspect tires and brake components
With all wheels removed, inspect each tire for uneven wear patterns, cuts, bulges, or embedded objects. Check brake pads for remaining thickness, brake rotors for scoring or excessive wear, and inspect brake lines for leaks or damage. Note any issues for future service.
5
Rotate tires in rearward cross pattern
For RWD Levante with non-directional tires: Move left front tire to right rear position. Move right front tire to left rear position. Move left rear tire to left front position. Move right rear tire to right front position. This rearward cross pattern is recommended for rear-wheel drive vehicles.
⚠If tires are directional (indicated by arrows on sidewall), use front-to-rear rotation only, keeping tires on the same side of vehicle.
6
Install wheels and hand-tighten lug nuts
Mount each wheel in its new position, ensuring the hub surface is clean and free of debris. Install all five lug nuts on each wheel by hand, threading them clockwise. Tighten by hand until the wheel is pulled flush against the hub, then snug with lug wrench in a star pattern.
7
Raise vehicle and remove jack stands
Using the hydraulic jack, carefully raise one end of the vehicle at a time to remove the jack stands. Lower the vehicle completely until all four tires are on the ground with full vehicle weight supported.
8
Torque lug nuts to specification
Using a calibrated torque wrench, torque each wheel's lug nuts to 130 Nm (96 lb-ft) in a star pattern (tighten one, skip to opposite, continue pattern). Go around twice to ensure even seating and proper torque on all lug nuts. This applies to the alloy wheels standard on the Levante.
Torque spec
Lug Nuts - Alloy Wheels130 Nm (96 lb-ft)
9
Adjust tire pressures
Check and adjust tire pressure in all four tires to the specifications listed on the driver's door jamb placard. Pressures may differ between front and rear axles. Ensure the tire pressure monitoring system (TPMS) sensors are functioning properly.

Reassembly

Remove wheel chocks and store all tools
Reset tire pressure monitoring system if required using vehicle settings menu
Record the tire rotation in the vehicle maintenance log with current mileage

Verification

Drive vehicle 50 miles, then re-torque all lug nuts to 130 Nm (96 lb-ft) in a star pattern to ensure proper seating
Verify no vibrations or unusual noises during test drive
Confirm tire pressure monitoring system shows correct pressures for all four tires
Check that all lug nuts remain tight and wheels are secure

🔧Stuck on this tire rotation? Take it to The Diag Desk.A human with 20+ years in the bay answers about YOUR Maserati within 24 hours — never AI. $25, and you're not charged unless you get an answer.Ask a tech →