🌍 International coverage, work in progress. This Russian-market vehicle is part of our hand-curated international catalog. We are filling in labor times, torque specs and fluids as fast as we can verify them, so some numbers may be missing or marked estimated for now. Do you work on these vehicles in the EU, Russia, or the JDM scene? Help us get it right: send real shop times or corrections to [email protected], or request the data you need and it joins the verification queue.
2000MERCEDES-BENZCLK55 AMG C208
5.4L V8 M113•RWD•AUTOMATIC•gas•M113
Be the first sponsor for this vehicle
For $99, we generate the full set of step-by-step repair procedures for this exact vehicle. Free for everyone, forever, with your name on every one.
The C208 CLK55 AMG with the M113 5.4L V8 is a solid high-performance platform when maintained, but the early M113 engines are notorious for wiring harness deterioration and head bolt issues that can escalate to catastrophic internal failures if neglected. Budget for expensive transmission and engine work if you're shopping beyond 100k miles.
Engine Wiring Harness Deterioration
Common · medium severity
Typical onset: 80,000-120,000 mi
Symptoms: rough idle or misfires, check engine light with multiple cylinder misfire codes, hard starting when hot, oil seepage around valve covers where harness sits
Fix: Early M113 harnesses used biodegradable insulation that cracks and exposes wires. Requires both engine harness replacement—8-12 hours labor depending on whether you pull the intake manifold or work around it. Valve cover gaskets usually done at same time since access is already there.
Estimated cost: $2,000-3,500
Head Bolt Thread Failure Leading to Head Gasket Blowout
Occasional · high severity
Typical onset: 100,000-150,000 mi
Symptoms: coolant loss with no external leaks, white smoke from exhaust, milky oil, overheating, sudden loss of compression on one bank
Fix: M113 aluminum blocks can strip head bolt threads, especially if previously overheated or if bolts were over-torqued. Requires head removal, thread repair with Heli-Coil or Time-Sert inserts, new head gaskets, and complete head resurfacing. 20-30 hours labor for both banks if doing it right. Some engines need short block replacement if thread damage is severe.
Estimated cost: $4,500-8,000
5G-Tronic Transmission Valve Body and Conductor Plate Failure
Common · high severity
Typical onset: 120,000-180,000 mi
Symptoms: harsh 2-3 or 3-4 shifts, transmission slipping or flaring between gears, limp mode with fault codes, delayed engagement into drive or reverse, no movement in any gear
Fix: The 722.6 five-speed is generally stout behind the AMG torque, but the valve body conductor plate develops cracks in solder joints and the valve body solenoids wear. Requires transmission drop, valve body removal, and either rebuild or replacement of conductor plate and solenoids. 8-12 hours labor. Often combined with fluid/filter service and new transmission mount.
Estimated cost: $2,200-3,800
Front Engine and Transmission Mounts
Common · low severity
Typical onset: 60,000-100,000 mi
Symptoms: clunk on takeoff or when shifting into drive/reverse, vibration at idle in gear, excessive engine movement visible from engine bay, drivetrain shudder under acceleration
Fix: Hydraulic mounts fail from age and the AMG torque accelerates wear. Front engine mount and transmission mount are the usual culprits. 3-5 hours labor for both. Use OE or Lemförder—aftermarket junk fails quickly under this engine's torque.
Estimated cost: $800-1,400
Crankshaft Position Sensor and Camshaft Position Sensor Failures
Occasional · high severity
Symptoms: random no-start condition, stalling while driving with no warning, crank/no-start when hot, intermittent check engine light, engine cuts out then restarts seconds later
Fix: Heat-related sensor failures leave you stranded. Crank sensor is accessible at front of engine near harmonic balancer (1.5 hours), cam sensors are under valve covers (3-4 hours each side with harness work). Keep spares in the trunk if you daily-drive this car.
Estimated cost: $300-900
Rear Subframe Mounting Point Rust and Cracking
Occasional · high severity
Symptoms: clunking from rear on bumps, steering wheel off-center or wandering, visible rust or cracking around rear subframe mounts, uneven rear tire wear
Fix: Northern cars and cars with prior body damage can develop rust or cracking where the rear subframe bolts to the unibody. Inspection requires a lift—look for rust jacking or cracks in the sheet metal. Proper repair involves cutting out metal and welding in reinforcement plates, then re-mounting subframe. 12-20 hours if structural welding is needed. Safety-critical—do not ignore.
Estimated cost: $2,500-5,000
Owner tips
Change transmission fluid every 40k miles with genuine MB fluid—the 'lifetime fill' myth kills these transmissions
Inspect engine wiring harness annually after 80k miles; early replacement avoids misfire damage to cats
Keep coolant system immaculate—overheating even once can start the head bolt thread failure cascade
Use quality 0W-40 synthetic and 5k mile oil changes; M113 has tight tolerances and sludge kills cam adjusters
Budget $3k-5k in deferred maintenance on any sub-$15k example—if the PO couldn't afford maintenance, you're inheriting their problem
Buy one only if maintenance records are thick and you have a $5k repair fund—when they're right they're spectacular, but neglected examples grenading engines are common enough to be cautious.
AI-assisted summary drawn from NHTSA recall data, our labor-times database, and platform knowledge. Not a substitute for a pre-purchase inspection on a specific vehicle.
No labor entries for this vehicle.
🔧
Be the first to unlock repairs for the 2000 Mercedes-Benz CLK55 AMG C208
Procedures haven't been generated for this vehicle yet. Become the founding sponsor and we'll generate expert-grade, step-by-step repair walkthroughs for every common job on it — free for every mechanic and DIYer who looks it up after, forever.
One-time payment · Your name at the top of every procedure · Powers open data for everyone
No torque specs for this vehicle.
No fluid specs for this vehicle.
No DTC data for this vehicle.
No battery specs for this vehicle.
Every control module on the 1999-2002 Mercedes-Benz CLK55 AMG C208 — where it lives, replacement time, and what it takes to program a replacement. Modules marked dealer / factory tool won't work after a part swap alone — budget for programming.
⚠️ Optional equipment. Analog cellular network no longer functional in US. VIN coding required if present.
Seat Control Module (SCM)0.6 hr R&Rrelearn only +0.2 hr▸ programming details
📍 Under driver/passenger seat
🔧 Star Diagnosis or Autel
⚠️ Memory seats only. Simple relearn procedure. Left and right modules independent.
Aftermarket tool coverage varies by software version and vehicle build — treat "aftermarket tool" rows as "usually possible" and verify against your tool maker's coverage list before promising a customer. Spot a wrong location or hour? Tell us — corrections ship fast here.
No maintenance entries for this vehicle.
🌧️ Wiper Blades
2000single front blade
26″
Front (single blade)
Attachmenthook
This generation uses one Monoblade-style front wiper that sweeps the whole windshield — don't buy a pair.
📝 C208 coupe, no rear wiper. Both blades same length. Single front Monoblade-style wiper.
Size-standard part numbers — verify your connector type before buying. Rear blades are model-specific; check the package's vehicle list.
Fuel economy figures are EPA data via fueleconomy.gov (median across matching trims). Performance figures are compiled estimates for the 2000 Mercedes-Benz CLK55 AMG C208 5.4L V8 M113 and can vary by trim.
🔧 Database maintained under the daily editorial review of Chris Hackleman · Master Technician · 20+ years.