Free API
4.0L Turbo V8•4WD•AUTOMATIC•gas•M177•turbo
Founding sponsor spot is openYour name on every procedure for this vehicle, permanently.Sponsor — $99 →
engine

Engine R&R

for 2021 Mercedes-Benz G-Class 4.0L Turbo V8 · 4WD
Difficulty
Expert
Time
14.5 h
Tools
17
Steps
12
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

Complete removal and reinstallation of the M176 4.0L twin-turbo V8 engine from a 2019 Mercedes-Benz G-Class, including disconnection of all ancillary systems, subframe/crossmember removal, and engine extraction from above.

Warnings

⚠️This engine weighs approximately 470 lbs without ancillaries. Ensure engine hoist and lifting equipment are rated for at least 1500 lbs and all chains/straps are in good condition.
⚠️The fuel system operates at high pressure (up to 200 psi). Relieve fuel pressure completely before disconnecting any fuel lines. Fuel will spray under pressure if lines are disconnected without proper depressurization.
⚠️R-1234yf refrigerant is mildly flammable. Recovery must be performed by certified technicians using approved equipment. Do not vent refrigerant to atmosphere.
⚠The twin turbochargers and exhaust components retain heat for hours after engine shutdown. Allow engine to cool completely before beginning work.
⚠The 9G-TRONIC transmission weighs approximately 220 lbs. Use a transmission jack at all times when supporting it during engine removal.
⚠Document all electrical connector orientations and routing with photographs before disconnection. The M176 engine has over 40 electrical connections.
ℹ️Mercedes-Benz Star Diagnostic System is required to perform SCN coding after engine installation. Plan for dealer or specialist support if SDS is unavailable.
ℹ️This procedure assumes engine-only removal. The transmission remains in the vehicle supported by a transmission jack.

Tools required

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Fluids

  • 0W-40 full synthetic engine oil — 9.5 qt
  • MB 325.5 coolant (purple) — 29 qt

Preparation

  1. Park vehicle on level ground and engage parking brake. Chock rear wheels.
  2. Disconnect battery negative terminal, then positive terminal. Move cables away from battery posts to prevent accidental reconnection.
  3. Relieve fuel system pressure: remove fuel pump fuse (F87 in rear SAM module), start engine and allow it to stall, then crank for 5 seconds to ensure complete depressurization.
  4. Remove engine cover and both turbocharger heat shields.
  5. Raise vehicle on lift or with jack stands to provide access from above and below simultaneously. Minimum 24 inches of ground clearance recommended.
  6. Remove front wheels.
  7. Remove engine undertray panels and front belly pan (multiple Torx fasteners).
  8. Drain engine coolant from radiator petcock and engine block drain plugs into appropriate container. Total capacity is 29 quarts.
  9. Drain engine oil and remove oil filter.
  10. Recover A/C refrigerant using certified R-1234yf recovery equipment.
  11. Photograph all wiring harness routing, vacuum line connections, and coolant hose positions for reinstallation reference.
  12. Place fender covers on both fenders to protect paint during engine hoist operation.

Procedure

  1. 1
    Disconnect air intake system
    Remove engine air filter housing assembly. Disconnect mass airflow sensor connector. Loosen clamps securing intake ducts to both turbocharger inlets. Remove both turbocharger air intake tubes and crossover ducting. Disconnect crankcase breather hoses from valve covers. Remove air intake resonator box if equipped.
  2. 2
    Disconnect cooling system components
    Disconnect upper and lower radiator hoses at engine. Disconnect heater hoses at firewall connections (2 hoses). Disconnect coolant reservoir hose. Disconnect transmission cooler lines at radiator (cap immediately to prevent ATF spillage). Remove radiator fan shroud assembly: disconnect fan module electrical connector, remove 4 mounting bolts securing fan shroud to radiator, and lift fan shroud assembly clear. Remove radiator: remove remaining mounting bolts and lift radiator straight up and out of vehicle.
  3. 3
    Disconnect fuel system
    Locate fuel supply and return lines on driver side fuel rail. Using appropriate fuel line disconnect tools, separate quick-connect fittings at fuel rails. Have rags ready to absorb residual fuel. Cap or plug all open fuel lines immediately to prevent contamination. On passenger side, disconnect fuel pressure sensor connector.
  4. 4
    Disconnect electrical connections - engine top
    Working from front to rear on both sides, disconnect all engine harness connections: both ignition coil connectors (8 total), camshaft position sensors (4 total - 2 per bank), throttle body connector, fuel injector connectors (8 total), knock sensors (2 total), oil pressure sensor, oil level sensor, coolant temperature sensors (multiple), variable valve timing solenoids (4 total - 2 per bank), and oxygen sensors (4 total - 1 pre-cat and 1 post-cat per bank). Use oxygen sensor socket for O2 sensor removal if necessary.
  5. 5
    Disconnect A/C and power steering
    Disconnect A/C compressor electrical connector. Remove A/C compressor mounting bolts and position compressor aside without disconnecting refrigerant lines (support with wire or strap - do not allow weight to hang on lines). There is no power steering pump to remove as this vehicle uses electric power steering.
  6. 6
    Disconnect exhaust system
    From underneath vehicle, disconnect exhaust system at turbocharger outlets. Each turbocharger has an exhaust downpipe secured by 3 bolts with spring-loaded connections. Remove the turbo-to-downpipe fasteners on both sides. The exhaust system forward of the catalytic converters will drop down. Support exhaust pipes to prevent damage to hangers. If oxygen sensors were not previously removed from exhaust, disconnect their wiring harnesses now.
  7. 7
    Disconnect transmission from engine
    Position transmission jack under transmission to support its weight. Remove torque converter access cover on transmission bell housing. Mark torque converter-to-flexplate relationship for reinstallation. Remove torque converter-to-flexplate bolts (rotate crankshaft via front crank bolt to access each; verify exact bolt count against MB service data for the 725.0/9G-TRONIC). Remove bell housing-to-engine mounting bolts. On the 9G-TRONIC (725.0) transmission mated to this engine, the bell housing bolts are of varying lengths - document exact count and locations per MB service data before removal. Disconnect transmission wiring harness connectors at transmission. Carefully slide transmission back approximately 2 inches on transmission jack to disengage input shaft from torque converter, then secure transmission on jack.
  8. 8
    Disconnect remaining engine harnesses and accessories
    From underneath, disconnect starter motor connections (power cable and trigger wire). Remove starter motor mounting bolts and remove starter. Disconnect alternator main power cable (large nut on back of alternator) and alternator field connector. Disconnect ground straps from engine block to chassis (typically 2 locations - one on each side of engine block). Disconnect engine wiring harness main connector at firewall pass-through. Release harness from any remaining clips securing it to engine.
  9. 9
    Remove front subframe/crossmember
    Support front subframe with floor jack positioned at center of subframe. Remove front subframe mounting bolts. Verify against MB WIS whether front subframe/crossmember removal is required for engine-only R&R on the 463/467 chassis; the engine mount attachment method and bolt count must be confirmed before proceeding. Once all mounting bolts are removed, carefully lower the subframe assembly on the floor jack and roll it clear of the vehicle. The engine mounts will remain attached to the subframe during this process. Note: Torque subframe mounting bolts to the exact MB-specified value and torque-angle sequence (these are large structural fasteners requiring high torque, likely 150+ Nm; verify against MB service data and confirm whether they are single-use torque-to-yield bolts).
  10. 10
    Remove auxiliary drive belt and accessories
    Using a breaker bar on the belt tensioner, rotate tensioner clockwise to release tension and remove serpentine belt from pulleys. If alternator was not previously removed, remove alternator mounting bolts and remove alternator. Remove power steering pump pulley and idler pulleys if they interfere with engine lifting (typically secured with center bolts). Note that some accessories may be easier to remove with engine partially lifted.
  11. 11
    Attach lifting equipment and remove engine
    Install engine lifting equipment only at the manufacturer-designated engine hoist attachment points on the M176. Do NOT use cylinder head cover (valve cover) bolt holes, which cannot support engine weight. Verify correct lifting points in MB service documentation. Attach engine hoist chains to lifting brackets. Connect load leveler to hoist and carefully take up tension to support engine weight. Double-check that all connections, hoses, wiring, and transmission separation are complete. Slowly lift engine, adjusting angle with load leveler to clear transmission input shaft housing, front crossmember area, and firewall clearance. The engine will need to be angled with front tilted up approximately 15-20 degrees to clear the transmission and body during extraction. Once clear of engine bay, raise to safe working height and move to engine stand or work area.
    ⚠️Verify all connections are disconnected before lifting. An attached component can cause catastrophic damage or injury during lift operation.
    ⚠Have an assistant guide the engine during extraction to prevent body panel damage. Maintain constant communication with hoist operator.
  12. 12
    Inspect and prepare for reinstallation
    With engine removed, inspect engine bay for any damaged wiring, loose fasteners, or leaking seals. Clean any oil or coolant residue from chassis. Inspect transmission input shaft seal for leakage; replace if necessary. Inspect engine mount bushings on subframe; replace if torn or deteriorated. If engine removal was for major internal repairs, now is the time to perform that work. If installing a replacement engine, transfer all necessary accessories, sensors, and ancillaries from old engine to replacement unit.

Reassembly

  1. Reinstallation follows removal in reverse order with these critical notes:
  2. Before lowering engine into bay, ensure transmission is properly positioned and supported on transmission jack. Verify torque converter is fully seated in transmission pump (should be recessed approximately 1 inch from bell housing face).
  3. When mating engine to transmission, align torque converter with flexplate using marks made during disassembly. Guide engine onto alignment dowels carefully - do not force. Bell housing should mate flush with engine block without gaps.
  4. Install bell housing bolts in correct positions (varying lengths). Torque bell housing bolts following OEM sequence if specified in service manual, or cross-pattern from center outward. Then install torque converter-to-flexplate bolts through access cover, applying thread locker to bolts. Rotate engine as needed to access all 6 bolts.
  5. Install front subframe/crossmember assembly with engine mounts attached. Align subframe mounting points carefully before inserting bolts. Torque subframe mounting bolts to 55 Nm (40 lb-ft) - this is a critical structural fastener.
  6. Reconnect all electrical connectors using photographs taken during disassembly as reference. Ensure all connectors are fully seated with locking tabs engaged.
  7. Install new turbocharger-to-exhaust gaskets when reconnecting downpipes. Torque turbo downpipe fasteners evenly in cross-pattern.
  8. When reconnecting A/C compressor, verify belt alignment before installing serpentine belt. Check that compressor rotates freely by hand before belt installation.
  9. Reconnect all coolant hoses with new clamps if originals show wear. Ensure heater hoses are routed correctly to prevent kinking.
  10. Reconnect fuel lines - ensure quick-connect fittings are fully engaged (should hear/feel a click). Tug on lines to verify secure connection.
  11. Install radiator and fan shroud assembly. Ensure radiator mounting insulators are properly seated. Reconnect transmission cooler lines with new sealing washers.
  12. Reinstall air intake system in reverse of removal. Ensure all duct clamps are tight and mass airflow sensor connector is secure.
  13. Reinstall engine undertray panels and belly pans.
  14. Install new oil filter and fill engine with 9.5 quarts of 0W-40 full synthetic oil meeting Mercedes-Benz 229.5 specification.
  15. Fill cooling system with 29 quarts of MB 325.5 purple coolant. Bleed cooling system according to MB procedure (typically involves running engine with climate control heater on max while monitoring coolant level).
  16. Reconnect battery positive terminal first, then negative terminal.
  17. Before starting engine, perform a final walk-around inspection to verify all tools are removed, all fasteners are tight, and no wiring or hoses are pinched or misrouted.

Verification

  • Using Mercedes-Benz Star Diagnostic System or equivalent professional scan tool, perform SCN coding to register engine installation/replacement. Clear any fault codes that may have been stored during removal process.
  • Prime fuel system: turn ignition to ON position (without starting) for 5 seconds, then OFF. Repeat 3-4 times to build fuel pressure. Check for fuel leaks at all connection points.
  • Check for coolant and oil leaks around all connection points before starting engine.
  • Start engine and listen for unusual noises. Allow to idle for 2-3 minutes while monitoring for leaks. Check oil pressure gauge/warning light - should show normal pressure immediately upon startup.
  • With engine running, check for exhaust leaks at turbocharger-to-downpipe connections (listen for hissing or ticking sounds).
  • Verify cooling fans activate when commanded by scan tool or when coolant temperature reaches operating threshold.
  • Turn on A/C system and verify compressor engages and cooling is effective. Have A/C system recharged if refrigerant was lost during compressor removal.
  • Check transmission fluid level and condition. Add MB 236.17 ATF if needed (some fluid loss may occur during separation).
  • With engine at operating temperature, check coolant level in reservoir and top off if necessary. Inspect for coolant leaks at all hose connections.
  • Perform a test drive to verify normal engine operation, smooth acceleration, proper transmission shifting, and absence of warning lights. Monitor engine temperature gauge throughout test drive.
  • After test drive, re-inspect all connection points for leaks while engine is hot. Re-torque cylinder head cover bolts if lifting brackets were installed in those positions.
  • If any diagnostic trouble codes are present after test drive, address them before returning vehicle to service. Common codes after engine R&R include oxygen sensor readiness, transmission adaptations not complete, or EVAP system large leak (often due to misrouted or disconnected vacuum lines).

Related trouble codes on this vehicle

Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.

Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →

🔧Stuck on this engine r&r? Take it to The Diag Desk.A human with 20+ years in the bay answers about YOUR Mercedes-Benz within 24 hours — never AI. $25, and you're not charged unless you get an answer.Ask a tech →

More procedures for this vehicle

For shop owners
Want more customers to find you?
We build shop websites with online booking onto your schedule and your own online store.
Talk to the ownerSee what's included
Built by a shop owner. Talk to Chris, not a sales rep.
🔧 Built by master technician Chris Hackleman · Master Technician · 20+ years. Spot an error? Use the Help link above — a human reads every report.
Stuck on this repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
⚠ STILL BEHIND THE PAYWALL
The 2021 Mercedes-Benz G-Class repair data is incomplete because no one has sponsored it yet. For $99, we generate the full step-by-step procedures, then fact-check them with a second AI pass and your expert review. Your name on every procedure, permanently.
The same data would cost $169/mo from Mitchell1 or $30/year from ALLDATAdiy — and you'd be renting access, not freeing it. Sponsor once, free forever.
Sponsor the Mercedes-Benz G-Class — $99 →
Building an app?
Free API key: 10 requests/day, 100/month, no card required.
Get an API key →
Run a shop?
A free website, SEO and Google reviews with your shop software. Auto Shop Base Professional, $250/mo, with our labor times on every estimate.
See what's included →