The 2019 GLS (X166 chassis) is the final year of the older platform before the 2020 redesign. While generally robust, the turbocharged engines—especially the M276 3.0L V6 and M278 4.0L V8—are showing catastrophic internal failures at surprisingly low mileage, often tied to bearing wear and oil starvation issues.
Symptoms: Metallic knocking or ticking from lower engine, especially on cold start, Oil pressure warning light or low oil pressure at idle, Metal shavings in oil during changes, Sudden loss of power, engine seizing
Fix: Rod or main bearings fail due to inadequate oil supply to crank journals, often requiring complete short block or engine replacement. Common root cause is design flaw in oil pump or gallery restrictors. 30-45 hours labor for engine R&R plus machine work or replacement block.
Estimated cost: $15,000-28,000
Transmission Oil Cooler Line Leaks (722.9 / 9G-Tronic)
Common · medium severity
Typical onset: 50,000-90,000 mi
Symptoms: Transmission fluid pooling under vehicle, usually passenger side, Burnt ATF smell after highway driving, Harsh shifts or slipping when fluid level drops, Check engine light with transmission overheat codes
Fix: Cooler lines crack at crimped fittings or corrode at frame contact points. Requires replacement of hard lines and sometimes auxiliary cooler. 3-5 hours labor plus fluid flush.
Estimated cost: $800-1,600
Engine and Transmission Mount Failures
Common · medium severity
Typical onset: 60,000-100,000 mi
Symptoms: Clunking or thudding when shifting from Park to Drive, Excessive vibration at idle, especially with AC on, Visible sagging of engine when inspected from below, Steering wheel shake during acceleration
Fix: Hydraulic mounts lose fluid and collapse, particularly right-side engine mount and rear transmission mount. Replace in pairs for best results. 4-6 hours labor depending on which mounts.
Estimated cost: $1,200-2,200
Turbocharger Wastegate Rattle and Failure (M276 V6)
Occasional · medium severity
Typical onset: 70,000-110,000 mi
Symptoms: Rattling noise on cold start that disappears after 30 seconds, Loss of boost pressure, sluggish acceleration, Check engine light with underboost or overboost codes (P0234, P2263), Excessive black smoke under hard acceleration
Fix: Wastegate actuator arms stick or rattle due to carbon buildup. Early stages can be cleaned, but most need turbo replacement. Each turbo is 8-10 hours labor due to tight packaging.
Estimated cost: $3,500-6,000
Airmatic Air Suspension Compressor and Strut Leaks
Common · medium severity
Typical onset: 70,000-120,000 mi
Symptoms: Vehicle sitting low, especially overnight or in cold weather, Compressor running constantly or cycling frequently, 'Airmatic Visit Workshop' warning on dash, Uneven ride height corner to corner
Fix: Air struts develop leaks at crimp seals or bellows. Compressor wears out from overwork. Struts are 2-3 hours each; compressor is 3-4 hours. Often multiple corners fail within 20k miles of each other.
Estimated cost: $1,800-3,200 per strut, $2,500-3,500 compressor
Fuel Filter Clogging and Low Pressure Issues
Occasional · medium severity
Typical onset: 50,000-80,000 mi
Symptoms: Hard starting, especially after sitting overnight, Stumbling or hesitation under acceleration, Check engine light with fuel trim or low fuel pressure codes, Engine dying at idle or refusing to restart when hot
Fix: In-tank fuel filter clogs prematurely, often from contaminated fuel or tank varnish. Requires dropping tank and replacing entire pump assembly in most cases. 4-6 hours labor.
Estimated cost: $1,200-2,000
Cylinder Head Gasket Leaks (M278 V8)
Rare · high severity
Typical onset: 60,000-100,000 mi
Symptoms: White smoke from exhaust on startup, Coolant loss with no visible external leaks, Milky oil on dipstick or oil cap, Overheating under load, bubbling in coolant reservoir
Fix: Head gaskets fail between cylinders or into coolant passages, often combined with head warping. Requires both heads off, resurfacing, and new gaskets. 25-35 hours labor.
Estimated cost: $8,000-14,000
Owner tips
Use only Mercedes-approved 0W-40 or 5W-40 oil and change every 5,000 miles maximum—extended intervals accelerate bearing wear on these engines
Inspect transmission fluid color and level every oil change; dark or burnt smell means immediate flush needed
Budget $2,000-3,000/year for suspension and drivetrain maintenance after 60k miles if keeping Airmatic
Get a pre-purchase inspection focusing on oil analysis and borescope of cylinders—internal engine damage often has no warning
Only buy if you can afford a potential $20k engine replacement or find one with documented short block replacement under warranty—the bearing failures are a ticking time bomb that make even low-mileage examples risky.
AI-assisted summary drawn from NHTSA recall data, our labor-times database, and platform knowledge. Not a substitute for a pre-purchase inspection on a specific vehicle.
Fitment notes: AGM battery required; located under front passenger seat or in engine bay depending on configuration
As an Amazon Associate, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.
Every control module on the 2018-2020 Mercedes-Benz GLS — where it lives, replacement time, and what it takes to program a replacement. Modules marked dealer / factory tool won't work after a part swap alone — budget for programming.
Airmatic / Active Body Control Module (ABC/ADS)2.5 hr R&Rsecurity gateway +1.5 hr▸ programming details
📍 Front left engine bay or under vehicle near front axle
🔧 Xentry Diagnostics + SCN online
⚠️ VIN-locked. Requires ride height calibration, damper adaptation, and level sensor learning. System bleed may be required.
Transmission Control Unit (TCU)2.5 hr R&Rsecurity gateway +1.0 hr▸ programming details
📍 Transmission housing or adjacent to transmission
🔧 Xentry Diagnostics + SCN online
⚠️ VIN-locked, requires SCN coding. Transmission fluid change often required during R&R.
Signal Acquisition and Actuation Module - Roof (SAM-Roof)2.0 hr R&Rsecurity gateway +1.0 hr▸ programming details
⚠️ Separate modules for driver and passenger. Requires position calibration after replacement.
Aftermarket tool coverage varies by software version and vehicle build — treat "aftermarket tool" rows as "usually possible" and verify against your tool maker's coverage list before promising a customer. Spot a wrong location or hour? Tell us — corrections ship fast here.
Size-standard part numbers — verify your connector type before buying. Rear blades are model-specific; check the package's vehicle list.
Fuel economy figures are EPA data via fueleconomy.gov (median across matching trims). Performance figures are compiled estimates for the 2019 Mercedes-Benz GLS 4.0L Turbo V8 and can vary by trim.
🔧 Database maintained under the daily editorial review of Chris Hackleman · Master Technician · 20+ years and Jeff Moore · Master Lexus & Toyota Mechanic · 20+ years.