🌍 International coverage, work in progress. This Russian-market vehicle is part of our hand-curated international catalog. We are filling in labor times, torque specs and fluids as fast as we can verify them, so some numbers may be missing or marked estimated for now. Do you work on these vehicles in the EU, Russia, or the JDM scene? Help us get it right: send real shop times or corrections to [email protected], or request the data you need and it joins the verification queue.
Back to search

2022 NISSAN NV3500

5.6L V8•RWD•AUTOMATIC•gas•VK56VD
Be the first sponsor for this vehicle

For $99, we generate the full set of step-by-step repair procedures for this exact vehicle. Free for everyone, forever, with your name on every one.

Sponsor — $99
Dead battery / stuck in Park? Emergency neutral procedure for this NV3500 →
Every control module on the 2012-2024 Nissan NV3500 — where it lives, replacement time, and what it takes to program a replacement. Modules marked dealer / factory tool won't work after a part swap alone — budget for programming.
Electric Power Steering Control Unit (EPS)2.5 hr R&Raftermarket tool +0.5 hr▸ programming details
📍 Behind lower dash panel, driver side, integrated with steering column assembly
🔧 Nissan CONSULT-III Plus or Autel MaxiSys
⚠️ Steering angle sensor calibration mandatory after replacement; neutral position relearn required
Anti-lock Brake System Control Unit (ABS)2.0 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Engine bay, driver side inner fender near master cylinder, integrated with hydraulic unit
🔧 Nissan CONSULT-III Plus or Autel MaxiSys/Launch X431
⚠️ Brake bleeding required after replacement; VIN configuration and wheel sensor calibration needed
Transfer Control Module (4WD)2.0 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Under vehicle, mounted on transfer case (4WD models only)
🔧 Nissan CONSULT-III Plus or Autel MaxiSys
⚠️ Only on 4WD NV3500 models; controls front axle engagement; relearn procedure required after replacement
Body Control Module (BCM)1.8 hr R&Rdealer / factory tool +1.0 hr▸ programming details
📍 Behind driver side lower dash panel, left of steering column
🔧 Nissan CONSULT-III Plus with NTIS subscription
⚠️ VIN programming required; all keys must be re-registered; controls NATS immobilizer functions and body features
CAN Gateway (GW)1.8 hr R&Rdealer / factory tool +0.8 hr▸ programming details
📍 Integrated within BCM (2012-2017) or separate module behind dash (2018+)
🔧 Nissan CONSULT-III Plus with NTIS subscription
⚠️ 2018+ may have separate gateway module; controls CAN bus communication between networks; VIN programming required
Occupant Classification System Control Unit (OCS)1.5 hr R&Raftermarket tool +0.4 hr▸ programming details
📍 Under front passenger seat, integrated with seat weight sensor mat
🔧 Nissan CONSULT-III Plus or Autel MaxiSys
⚠️ Calibration required with specific weights; SRS system integration; affects passenger airbag deployment logic
Automatic Air Conditioner Control Unit (A/C)1.5 hr R&Rrelearn only +0.2 hr▸ programming details
📍 Behind center dash, integrated with HVAC control panel
🔧 Self-relearn procedure or Nissan CONSULT-III Plus
⚠️ Actuator calibration self-relearn by cycling ignition; manual models may be plug-and-play
Around View Monitor Control Unit (AVM)1.5 hr R&Raftermarket tool +0.5 hr▸ programming details
📍 Behind center dash, near AV unit (if equipped with 360-degree camera)
🔧 Nissan CONSULT-III Plus or Autel MaxiSys
⚠️ Optional on higher trims; camera calibration mandatory; requires all four cameras functional for operation
Transmission Control Module (TCM)1.5 hr R&Rdealer / factory tool +0.7 hr▸ programming details
📍 Engine bay, driver side firewall, adjacent to ECM or integrated into valve body (2012-2019 5-speed auto)
🔧 Nissan CONSULT-III Plus with NTIS subscription
⚠️ Valve body removal required on some models; adaptive values reset and relearn procedure mandatory after replacement
Engine Control Module (ECM)1.2 hr R&Rdealer / factory tool +0.8 hr▸ programming details
📍 Engine bay, driver side firewall, mounted on bulkhead near brake master cylinder
🔧 Nissan CONSULT-III Plus with NTIS subscription
⚠️ VIN programming and immobilizer registration required; NATS pairing with BCM and keys mandatory
Sonar Control Unit (SONAR)1.2 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Behind rear bumper, center, near hitch area (if equipped)
🔧 Nissan CONSULT-III Plus or Autel MaxiSys
⚠️ Optional equipment; sensor calibration required after replacement; not available on all trim levels
Supplemental Restraint System Control Module (SRS)1.0 hr R&Raftermarket tool +0.4 hr▸ programming details
📍 Center console area, under center floor between front seats
🔧 Nissan CONSULT-III Plus or Autel MaxiSys/Launch X431
⚠️ Battery disconnect and 3-minute wait mandatory; crash data must be cleared; occupant classification system relearn required
Intelligent Power Distribution Module (IPDM-E/R)1.0 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Engine bay, driver side firewall, near battery or fuse box
🔧 Nissan CONSULT-III Plus or Autel MaxiSys
⚠️ Controls fuel pump relay, cooling fans, and multiple power distribution functions; VIN configuration recommended
Audio Visual Control Unit (AV)1.0 hr R&Rrelearn only +0.1 hr▸ programming details
📍 Center dash, integrated with radio/display unit
🔧 Self-configuration or Nissan CONSULT-III Plus
⚠️ Radio code may be required on some models; navigation models may need map data transfer
Combination Meter (METER)0.8 hr R&Rdealer / factory tool +0.5 hr▸ programming details
📍 Instrument panel, behind gauge cluster face
🔧 Nissan CONSULT-III Plus with NTIS subscription
⚠️ Odometer programming requires dealer access; VIN and mileage transfer mandatory for legal compliance
Nissan Anti-Theft System Control Unit / Intelligent Key Control Module (NATS)dealer / factory tool +0.8 hr▸ programming details
📍 Integrated within BCM (behind driver side lower dash) and IPDM-E/R
🔧 Nissan CONSULT-III Plus with NTIS subscription
⚠️ Not a separate module; function integrated in BCM; all keys must be present for registration; PIN code required from Nissan
Aftermarket tool coverage varies by software version and vehicle build — treat "aftermarket tool" rows as "usually possible" and verify against your tool maker's coverage list before promising a customer. Spot a wrong location or hour? Tell us — corrections ship fast here.
🔧 Database maintained under the daily editorial review of Chris Hackleman · Master Technician · 20+ years.
Stuck on a repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
Building an app?
Free API access to all this data — 10 requests/day, no card required.
Get an API key →
Run a shop?
Manage repairs, estimates, and customers with ShopBase — $249/mo, all features included. Built by the same team.
Try ShopBase →