The 2020 Rogue represents Nissan's third-generation crossover and largely avoids the catastrophic CVT failures that plagued 2014-2019 models, but the QR25DE engine has serious internal wear issues that frequently require major rebuilds between 80,000-120,000 miles, turning what should be a reliable commuter into a ticking time bomb.
Symptoms: Excessive oil consumption (1 qt per 500-1000 miles), Blue smoke on cold start or acceleration, Rough idle and misfires, Loss of compression evident in cylinder leak-down test, Check engine light with P0300-series misfire codes
Fix: This is a catastrophic internal failure requiring either complete engine rebuild (40-50 hours) with new pistons, rings, honing cylinders, and often crankshaft work, or short-block replacement (35-45 hours). Root cause appears to be inadequate piston-to-cylinder clearance combined with direct injection carbon buildup affecting ring sealing. Some techs successfully address early cases with piston ring replacement alone (25-30 hours), but full rebuild is often necessary once scoring starts.
Estimated cost: $6,500-11,000
CVT Transmission Oil Cooler Line Leaks
Occasional · medium severity
Typical onset: 60,000-90,000 mi
Symptoms: Pink fluid puddles under vehicle (ATF mixed with coolant), Transmission overheating warnings, Burnt transmission smell, Rough shifting or delayed engagement, Coolant level drops without visible external leaks
Fix: The CVT cooler lines crack where they connect to the radiator or at crimped fittings. While Nissan improved the CVT internals for 2020, the cooling system design carries over weak points from earlier generations. Repair involves replacing both supply and return lines plus flushing contaminated fluid (4-6 hours). If coolant mixes with ATF, full CVT fluid replacement with multiple drain-and-fills is critical to prevent valve body damage.
Estimated cost: $800-1,400
Transmission Mount Failure
Common · medium severity
Typical onset: 50,000-80,000 mi
Symptoms: Clunking when shifting from Park to Drive or Reverse, Excessive vibration at idle, especially with AC on, Visible engine/transmission movement when accelerating hard, Grinding sensation during acceleration from stop
Fix: The hydraulic front transmission mount deteriorates prematurely, likely due to additional stress from CVT operation. The mount is accessible from below but requires supporting the transmission while unbolting the old mount (2.5-3.5 hours). OEM replacement is significantly better than aftermarket — the hydraulic damping is critical for CVT smoothness.
Estimated cost: $450-700
Fuel System Contamination from In-Tank Filter Degradation
Occasional · medium severity
Typical onset: 70,000-110,000 mi
Symptoms: Hard starting, especially when hot, Intermittent stalling at idle or low speeds, Rough running and hesitation under acceleration, P0087 fuel pressure low code, Fuel pump noise/whining from tank area
Fix: The in-tank fuel filter screen disintegrates and contaminates the high-pressure fuel system, clogging injectors and damaging the fuel pump. Nissan doesn't sell the filter separately — you must replace the entire fuel pump module assembly (3-4 hours). If caught late, injectors may need ultrasonic cleaning or replacement, adding significant cost. This isn't covered under powertrain warranty despite being engine-related.
Estimated cost: $900-1,800
Head Gasket Failure Secondary to Overheating
Rare · high severity
Typical onset: 90,000-130,000 mi
Symptoms: White smoke from exhaust, Coolant mixing with oil (milky dipstick), Overheating episodes, Bubbles in coolant reservoir when running, Rapid coolant loss without external leaks
Fix: When piston ring wear causes oil consumption, some owners ignore it until severe overheating occurs, blowing head gaskets. Both heads typically need to be resurfaced and gaskets replaced (18-24 hours). If the engine already has ring issues, this repair is throwing good money after bad — better to do complete engine rebuild or replacement at this point.
Estimated cost: $3,200-5,000
Immobilizer Key Recognition Failure
Occasional · low severity
Symptoms: Intermittent no-start with security light flashing, Key not detected warning despite key being present, Push-button start fails to recognize key fob, Requires multiple attempts to start vehicle
Fix: This is the subject of a recall campaign — weak signal strength from the Intelligent Key system causes intermittent start failures. Dealer reprograms the BCM and key fobs (1-1.5 hours) under warranty or recall. Some cases require steering column module replacement. Not safety-critical but incredibly frustrating when it leaves you stranded.
Estimated cost: $0 (recall) to $600
Owner tips
Check oil level every 1,000 miles religiously — consumption above 1 qt per 3,000 miles means internal wear is starting; document everything for potential warranty claims
Change CVT fluid every 30,000-40,000 miles using only Nissan NS-3 fluid regardless of 'lifetime fill' marketing — this transmission needs fresh fluid to survive
Have a compression test and leak-down test performed at 60,000 miles to establish baseline — piston ring wear sneaks up on owners
Use Top Tier fuel and add periodic fuel system cleaner to minimize direct injection carbon buildup that accelerates ring wear
Replace transmission mount at first sign of clunking — delaying stresses the CVT internals unnecessarily
Pass on used examples unless under 50,000 miles with bulletproof maintenance records — the engine internal wear issue is a deal-breaker that transforms a $15,000 used crossover into a $10,000 repair bill with little warning.
AI-assisted summary drawn from NHTSA recall data, our labor-times database, and platform knowledge. Not a substitute for a pre-purchase inspection on a specific vehicle.
Fitment notes: Standard engine compartment location; AWD models may require specific hold-down configuration
As an Amazon Associate, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.
Every control module on the 2018-2020 Nissan Rogue — where it lives, replacement time, and what it takes to program a replacement. Modules marked dealer / factory tool won't work after a part swap alone — budget for programming.
Transmission Control Module (TCM)4.5 hr R&Rdealer / factory tool +1.0 hrCVT transmission (standard on all automatic models)▸ programming details
📍 CVT: integrated into CVT valve body inside transmission. Manual: not applicable
🔧 CONSULT-III Plus with NTIS subscription
⚠️ Requires transmission fluid drain and valve body removal. VIN programming and adaptive value initialization required. CVT fluid refill and relearn procedure adds 0.5 hours.
Electric Power Steering Control Module (EPS)2.5 hr R&Raftermarket tool +0.5 hr▸ programming details
📍 Integrated into electric power steering column assembly, below instrument panel at steering column
🔧 CONSULT-III Plus or Autel MaxiSys
⚠️ Typically replaced as assembly with steering column motor. Steering angle sensor calibration and zero-point learning required after replacement.
Anti-lock Brake System Control Module (ABS)1.8 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Engine compartment, driver side inner fender, mounted to ABS hydraulic unit
🔧 CONSULT-III Plus or Autel/Launch aftermarket tools
⚠️ Integrated with hydraulic unit; module alone can be replaced without bleeding if careful. Brake bleeding recommended. Basic configuration and wheel sensor calibration required.
Transfer Control Module (TCCM)1.5 hr R&Raftermarket tool +0.3 hrAWD models only (all Rogue models are AWD-capable; FWD is base)▸ programming details
📍 Under vehicle, mounted to transfer case assembly
🔧 CONSULT-III Plus or Autel
⚠️ Controls AWD engagement and torque distribution. Basic relearn procedure required after replacement.
📍 Engine compartment, driver side fender, integrated into Intelligent Power Distribution Module
🔧 CONSULT-III Plus with NTIS subscription
⚠️ Integrated with IPDM. All Intelligent Keys must be re-registered after replacement. Immobilizer pairing with ECM required. Some high-end aftermarket tools (Autel IM608) can program keys.
Body Control Module (BCM)1.5 hr R&Rdealer / factory tool +1.0 hr▸ programming details
⚠️ Controls lighting, wipers, door locks, power windows. VIN programming and configuration required. Intelligent Key registration must be performed after replacement.
Around View Monitor Control Module (AVM)1.5 hr R&Rdealer / factory tool +0.8 hrSL Premium Package with Around View Monitor (360-degree camera)▸ programming details
📍 Behind instrument panel, center, near AVN unit
🔧 CONSULT-III Plus with camera calibration
⚠️ Requires camera alignment and calibration procedure. Standard backup camera is integrated into AVN unit, not separate module.
Intelligent Power Distribution Module (IPDM)1.5 hr R&Rdealer / factory tool +0.8 hr▸ programming details
📍 Engine compartment, driver side fender, mounted to inner fender panel
🔧 CONSULT-III Plus with NTIS subscription
⚠️ Controls fuel pump, cooling fans, horn, and multiple power distribution functions. Also houses NATS immobilizer. VIN programming required.
Radar Control Module (RADAR)1.5 hr R&Rdealer / factory tool +1.0 hrSL with ProPILOT Assist (2018-2019) or Safety Shield 360 with intelligent cruise▸ programming details
📍 Behind front bumper, center, behind lower grille
🔧 CONSULT-III Plus with radar alignment tool
⚠️ Forward collision warning and adaptive cruise control. Requires precise alignment with special target after replacement or front-end collision repair.
Telematics Control Unit (TCU)1.5 hr R&Rdealer / factory tool +0.8 hrSV and SL trims with NissanConnect Services▸ programming details
📍 Behind instrument panel, passenger side, near glove box
🔧 CONSULT-III Plus with NTIS subscription and Nissan server activation
⚠️ Requires Nissan server activation and subscription pairing. Controls remote services, emergency call, stolen vehicle tracking.
📍 Behind instrument panel, center console area, near BCM
🔧 CONSULT-III Plus with NTIS subscription
⚠️ Manages CAN bus communication between networks. VIN programming required. Does not implement full security gateway lockout like VAG/BMW but does control module access.
Power Back Door Control Module (PBD)1.2 hr R&Raftermarket tool +0.3 hrSL and Platinum trims with power liftgate▸ programming details
📍 Rear liftgate, driver side, behind interior trim panel
🔧 CONSULT-III Plus or Autel
⚠️ Height memory and pinch protection calibration required after replacement.
📍 Engine compartment, driver side firewall, mounted on bulkhead above brake master cylinder
🔧 CONSULT-III Plus with NTIS subscription
⚠️ VIN programming and immobilizer pairing required. Some aftermarket tools (Autel MaxiSys Elite) can program with proper security credentials.
Automatic Air Conditioning Control Module (A/C)1.2 hr R&Rrelearn only +0.2 hr▸ programming details
📍 Behind center instrument panel, integrated into climate control head unit
🔧 Self-relearn procedure or CONSULT-III Plus
⚠️ Automatic climate control models. Self-calibration procedure available via button sequence. Manual climate control models use simple switch panel with no module.
Supplemental Restraint System Control Module (SRS)1.0 hr R&Rdealer / factory tool +0.5 hr▸ programming details
📍 Center console, beneath center stack, behind climate controls
🔧 CONSULT-III Plus with NTIS subscription
⚠️ Disconnect battery and wait 3 minutes before removal. VIN programming and crash data initialization required. Some aftermarket tools can clear codes but not program new modules.
Blind Spot Warning Control Module (BSW)1.0 hr R&Raftermarket tool +0.3 hrSV and above with Blind Spot Warning▸ programming details
📍 Behind rear bumper, driver side, near tail light assembly
🔧 CONSULT-III Plus or Autel
⚠️ Controls blind spot radar sensors. Sensor alignment typically automatic but can require calibration after rear-end collision repair.
Adaptive Front Lighting System Control Module (AFS)1.0 hr R&Raftermarket tool +0.3 hrSL Premium Package with LED headlights and adaptive lighting▸ programming details
📍 Behind front bumper, driver side, near headlight assembly
🔧 CONSULT-III Plus or Autel
⚠️ Controls headlight leveling and cornering function. Headlight aim calibration required after replacement.
Audio Visual Navigation Unit (AVN)1.0 hr R&Rrelearn only +0.3 hr▸ programming details
📍 Center instrument panel, integrated into touchscreen head unit
🔧 Self-initialization or CONSULT-III Plus
⚠️ Base audio models use simpler Audio Control Unit without navigation. Automatic CAN bus initialization on startup. Backup camera calibration may be needed.
Sonar Control Module (SONAR)0.8 hr R&Raftermarket tool +0.2 hrSV and above with rear parking sensors▸ programming details
📍 Behind rear bumper, center, above hitch area
🔧 CONSULT-III Plus or Autel
⚠️ Controls rear parking sensors. Sensor calibration typically automatic but can be manually triggered.
⚠️ Odometer programming required to transfer mileage. VIN programming required. Federal law requires documentation of mileage transfer.
Power Window Master Switch (PWMS)0.5 hr R&Rrelearn only +0.1 hr▸ programming details
📍 Driver door, integrated into master window switch assembly
🔧 Manual auto-up/down initialization procedure
⚠️ Controls all four power windows. Auto-up/down relearn required via window switch procedure after replacement or battery disconnect.
Aftermarket tool coverage varies by software version and vehicle build — treat "aftermarket tool" rows as "usually possible" and verify against your tool maker's coverage list before promising a customer. Spot a wrong location or hour? Tell us — corrections ship fast here.
Nissan North America, Inc. (Nissan) is recalling certain 2014-2020 Rogue and 2017-2022 Rogue Sport vehicles equipped with a jackknife style ignition key. The jackknife key may collapse into a folded position while driving.
Consequence: Driver contact with a key in the collapsed position could inadvertently shut off the vehicle while driving, increasing the risk of a crash. Additionally, if the vehicle shuts off while driving, the air bags may not deploy in a crash as intended, increasing the risk of injury.
Remedy: Dealers will insert a spacer into the key slot of the jackknife key, free of charge. Interim notification letters notifying owners of the safety risk were mailed March 29, 2023. Owner notification letters are expected to be mailed August 30, 2023. Owners may contact Nissan's customer service at 1-800-867-7669. Nissan's number for this recall is R22C5.
Size-standard part numbers — verify your connector type before buying. Rear blades are model-specific; check the package's vehicle list.
Fuel economy figures are EPA data via fueleconomy.gov (median across matching trims). Performance figures are compiled estimates for the 2020 Nissan Rogue 2.5L I4 QR25DE and can vary by trim.
🔧 Database maintained under the daily editorial review of Chris Hackleman · Master Technician · 20+ years and Jeff Moore · Master Lexus & Toyota Mechanic · 20+ years.