The 2023 Nissan Rogue represents the second year of the third-generation platform with significant turbo three-cylinder (VC-Turbo) and CVT reliability concerns emerging earlier than expected. Engine internal failures and transmission cooling issues are the headline problems on an otherwise competitive compact SUV.
Symptoms: Check engine light with misfire codes (P0300-P0303), Metallic knocking or ticking from engine bay, Loss of power under acceleration, Sudden onset of white/blue smoke from exhaust, Oil consumption between changes (1+ quart per 1,000 mi)
Fix: Complete engine rebuild or factory short-block replacement required. Piston ring failures, connecting rod bearing wear, and crankshaft damage documented. NHTSA has two recalls for internal engine components. Repair typically 20-28 hours labor depending on short-block vs full rebuild. Many failures occur within powertrain warranty but post-warranty cases are expensive.
Estimated cost: $8,500-14,000
CVT Transmission Oil Cooler Failure and Overheating
Common · high severity
Typical onset: 40,000-80,000 mi
Symptoms: Transmission warning light or limp mode activation, Slipping or delayed engagement when accelerating, Whining or grinding noise during acceleration, Burnt transmission fluid smell, Fluid leaks from cooler lines or radiator area
Fix: Oil cooler replacement with full CVT fluid flush required. Nissan CVTs remain heat-sensitive; cooler failures lead to rapid fluid degradation and internal CVT damage if not caught early. External cooler upgrade recommended for heavy loads or hot climates. 4-6 hours labor for cooler, but if CVT internals are damaged expect full replacement at 12-16 hours.
Symptoms: Excessive vibration at idle in Drive, Clunking when shifting from Park to Drive or Reverse, Rattling over bumps from engine bay, Visible engine movement when accelerating hard
Fix: Front transmission mount (dogbone mount) fails early due to CVT-specific stress patterns and undersized design. Aftermarket upgraded mounts available and recommended. 1.5-2.5 hours labor. Simple fix but annoying given low mileage failures.
Estimated cost: $350-650
Fuel Filter Clogging (Turbo Models)
Occasional · medium severity
Typical onset: 50,000-90,000 mi
Symptoms: Hesitation or stumbling during acceleration, Poor fuel economy (3-5 mpg drop), Rough idle or stalling at stops, Difficulty starting when hot, Turbo lag or boost cut-out
Fix: In-tank fuel pump/filter assembly on VC-Turbo models clogs earlier than conventional engines due to tighter tolerances. Tank drop required for replacement. Nissan doesn't list separate filter service but contamination issues documented. 2-3 hours labor.
Estimated cost: $450-850
Head Gasket Failure (1.5L VC-Turbo)
Rare · high severity
Typical onset: 60,000-100,000 mi
Symptoms: White smoke from exhaust on cold starts, Coolant loss with no visible leaks, Milky oil on dipstick or oil cap, Overheating or fluctuating temperature gauge, Rough idle with coolant smell from exhaust
Fix: Variable compression design with complex head bolt torque requirements. Head gasket failures less common than internal engine failures but documented. Head removal, resurface, new gasket and timing components. 12-16 hours labor. Often discovered during diagnosis of other engine problems.
Estimated cost: $3,200-5,500
Front Driver Airbag Inflator Recall Defect
Occasional · high severity
Symptoms: Airbag warning light (may be intermittent), Recall notice received by mail, No symptoms until potential deployment failure
Fix: NHTSA recall for driver-side frontal airbag inflator module. Safety-critical; potential for non-deployment or improper deployment in crash. Dealer replacement required, typically 1-2 hours. No cost to owner but appointment delays common due to parts availability.
Estimated cost: $0 (recall)
Owner tips
CVT fluid changes every 30,000-40,000 miles regardless of 'lifetime fill' claims — use only Nissan NS-3 spec fluid
Monitor oil level every 1,000 miles on VC-Turbo engines; consumption over 1 quart per 3,000 miles warrants dealership documentation for warranty
Check transmission cooler lines and radiator area for leaks during every oil change
Extended warranty strongly recommended if buying used — engine and CVT failures expensive and not uncommon under 100k
Keep all service records; Nissan frequently denies warranty claims for lack of maintenance documentation
Skip the VC-Turbo 1.5L if buying used without comprehensive warranty — the 2.5L four-cylinder is significantly more reliable, but CVT concerns remain across the board.
AI-assisted summary drawn from NHTSA recall data, our labor-times database, and platform knowledge. Not a substitute for a pre-purchase inspection on a specific vehicle.
Fitment notes: AGM battery required for vehicles with start-stop system
As an Amazon Associate, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.
Every control module on the 2021-2026 Nissan Rogue — where it lives, replacement time, and what it takes to program a replacement. Modules marked dealer / factory tool won't work after a part swap alone — budget for programming.
Transmission Control Module (TCM)4.5 hr R&Rdealer / factory tool +1.0 hrCVT transmission (standard on all automatic models)▸ programming details
📍 CVT: integrated into CVT valve body inside transmission. Manual: not applicable
🔧 CONSULT-III Plus with NTIS subscription
⚠️ Requires transmission fluid drain and valve body removal. VIN programming and adaptive value initialization required. CVT fluid refill and relearn procedure adds 0.5 hours. 2021+ uses updated CVT8 transmission.
Electric Power Steering Control Module (EPS)2.5 hr R&Raftermarket tool +0.5 hr▸ programming details
📍 Integrated into electric power steering column assembly, below instrument panel at steering column
🔧 CONSULT-III Plus or Autel MaxiSys
⚠️ Typically replaced as assembly with steering column motor. Steering angle sensor calibration and zero-point learning required after replacement.
Anti-lock Brake System Control Module (ABS)1.8 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Engine compartment, driver side inner fender, mounted to ABS hydraulic unit
🔧 CONSULT-III Plus or Autel/Launch aftermarket tools
⚠️ Integrated with hydraulic unit; module alone can be replaced without bleeding if careful. Brake bleeding recommended. Basic configuration and wheel sensor calibration required.
Body Control Module (BCM)1.5 hr R&Rdealer / factory tool +1.0 hr▸ programming details
⚠️ Controls lighting, wipers, door locks, power windows. VIN programming and configuration required. Intelligent Key registration must be performed after replacement. 2021+ has expanded feature set.
Around View Monitor Control Module (AVM)1.5 hr R&Rdealer / factory tool +0.8 hrSL and Platinum with Around View Monitor (360-degree camera)▸ programming details
📍 Behind instrument panel, center, near AVN unit
🔧 CONSULT-III Plus with camera calibration
⚠️ Requires camera alignment and calibration procedure. Standard backup camera is integrated into AVN unit, not separate module. 2021+ has improved resolution.
Intelligent Power Distribution Module (IPDM)1.5 hr R&Rdealer / factory tool +0.8 hr▸ programming details
📍 Engine compartment, driver side fender, mounted to inner fender panel
🔧 CONSULT-III Plus with NTIS subscription
⚠️ Controls fuel pump, cooling fans, horn, and multiple power distribution functions. Also houses NATS immobilizer. VIN programming required.
📍 Engine compartment, driver side fender, integrated into Intelligent Power Distribution Module
🔧 CONSULT-III Plus with NTIS subscription
⚠️ Integrated with IPDM. All Intelligent Keys must be re-registered after replacement. Immobilizer pairing with ECM required. Some high-end aftermarket tools (Autel IM608 Pro) can program keys.
Intelligent Driver Alertness Control Module (I-DA)1.5 hr R&Rdealer / factory tool +0.5 hrSL and Platinum with Intelligent Driver Alertness (2021+)▸ programming details
📍 Behind instrument panel, integrated with BCM or cluster
🔧 CONSULT-III Plus
⚠️ Monitors driver attention and steering patterns. Software-based function integrated with other modules; rarely requires standalone replacement. Calibration via CONSULT-III Plus.
Radar Control Module (RADAR)1.5 hr R&Rdealer / factory tool +1.0 hrStandard on SV and above with Safety Shield 360 (ProPILOT Assist on SL/Platinum)▸ programming details
📍 Behind front bumper, center, behind lower grille
🔧 CONSULT-III Plus with radar alignment tool
⚠️ Forward collision warning and adaptive cruise control. Requires precise alignment with special target after replacement or front-end collision repair. 2021+ has enhanced radar range.
Telematics Control Unit (TCU)1.5 hr R&Rdealer / factory tool +0.8 hrStandard on SV and above with NissanConnect Services▸ programming details
📍 Behind instrument panel, passenger side, near glove box
🔧 CONSULT-III Plus with NTIS subscription and Nissan server activation
⚠️ Requires Nissan server activation and subscription pairing. Controls remote services, emergency call, stolen vehicle tracking. 2021+ has enhanced connectivity features.
Transfer Control Module (TCCM)1.5 hr R&Raftermarket tool +0.3 hrAWD models (standard on SL and Platinum; optional on S and SV)▸ programming details
📍 Under vehicle, mounted to transfer case assembly
🔧 CONSULT-III Plus or Autel
⚠️ Controls AWD engagement and torque distribution. Basic relearn procedure required after replacement. 2021+ has refined AWD logic.
📍 Behind instrument panel, center console area, near BCM
🔧 CONSULT-III Plus with NTIS subscription
⚠️ Manages CAN bus communication between networks. VIN programming required. 2021+ has enhanced security protocols but still not full SGW lockout like European brands.
Power Back Door Control Module (PBD)1.2 hr R&Raftermarket tool +0.3 hrSL and Platinum trims with power liftgate▸ programming details
📍 Rear liftgate, driver side, behind interior trim panel
🔧 CONSULT-III Plus or Autel
⚠️ Height memory and pinch protection calibration required after replacement. 2021+ Platinum adds hands-free kick sensor functionality.
📍 Engine compartment, driver side firewall, mounted on bulkhead above brake master cylinder
🔧 CONSULT-III Plus with NTIS subscription
⚠️ VIN programming and immobilizer pairing required. 2021+ models have enhanced security. Some aftermarket tools (Autel MaxiSys Ultra) can program with proper security credentials.
Automatic Air Conditioning Control Module (A/C)1.2 hr R&Rrelearn only +0.2 hr▸ programming details
📍 Behind center instrument panel, integrated into climate control head unit
🔧 Self-relearn procedure or CONSULT-III Plus
⚠️ Automatic climate control models. Self-calibration procedure available via button sequence. Manual climate control models use simple switch panel with no module.
Audio Visual Navigation Unit (AVN)1.0 hr R&Rrelearn only +0.3 hr▸ programming details
📍 Center instrument panel, integrated into touchscreen head unit
🔧 Self-initialization or CONSULT-III Plus
⚠️ 2021+ uses updated NissanConnect system with larger touchscreen (8-inch or 9-inch). Automatic CAN bus initialization on startup. Backup camera calibration may be needed.
Supplemental Restraint System Control Module (SRS)1.0 hr R&Rdealer / factory tool +0.5 hr▸ programming details
📍 Center console, beneath center stack, behind climate controls
🔧 CONSULT-III Plus with NTIS subscription
⚠️ Disconnect battery and wait 3 minutes before removal. VIN programming and crash data initialization required. Some aftermarket tools can clear codes but not program new modules.
Adaptive Front Lighting System Control Module (AFS)1.0 hr R&Raftermarket tool +0.3 hrSL and Platinum trims with LED headlights and adaptive lighting▸ programming details
📍 Behind front bumper, driver side, near headlight assembly
🔧 CONSULT-III Plus or Autel
⚠️ Controls headlight leveling and cornering function. Headlight aim calibration required after replacement. 2021+ Platinum has matrix LED headlights with expanded functionality.
⚠️ Odometer programming required to transfer mileage. VIN programming required. Federal law requires documentation of mileage transfer. 2021+ uses fully digital cluster on higher trims.
Sonar Control Module (SONAR)0.8 hr R&Raftermarket tool +0.2 hrStandard on SV and above with rear parking sensors; front sensors on SL/Platinum▸ programming details
📍 Behind rear bumper, center, above hitch area
🔧 CONSULT-III Plus or Autel
⚠️ Controls front and rear parking sensors. Sensor calibration typically automatic but can be manually triggered. 2021+ has expanded sensor coverage.
Driver Seat Control Module (DSCM)0.8 hr R&Rrelearn only +0.1 hrSL and Platinum with power driver seat and memory function▸ programming details
📍 Under driver seat, integrated into seat frame
🔧 Self-relearn via seat memory buttons
⚠️ Controls power seat adjustment and memory positions. Memory positions stored in module; relearn via seat memory buttons after replacement. 2021+ Platinum has heated/ventilated seats controlled by this module.
Power Window Master Switch (PWMS)0.5 hr R&Rrelearn only +0.1 hr▸ programming details
📍 Driver door, integrated into master window switch assembly
🔧 Manual auto-up/down initialization procedure
⚠️ Controls all four power windows. Auto-up/down relearn required via window switch procedure after replacement or battery disconnect.
Aftermarket tool coverage varies by software version and vehicle build — treat "aftermarket tool" rows as "usually possible" and verify against your tool maker's coverage list before promising a customer. Spot a wrong location or hour? Tell us — corrections ship fast here.
ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL · 26V080000
2026-02-12
Nissan North America, Inc. (Nissan) is recalling certain 2023-2025 Rogue vehicles equipped with 3-cylinder 1.5L variable compression turbo (VC-Turbo) engines. Increased temperatures can break down the engine oil, which may cause the engine bearings to seize and become damaged, leading to engine failure.
Consequence: Engine failure can cause a loss of drive power, increasing the risk of a crash. A bearing failure may cause a breach in the engine block, allowing hot oil to be discharged, increasing the risk of an engine fire.
Remedy: Dealers will reprogram the engine control module (ECM) software, inspect for diagnostic trouble codes, and test drive the vehicle, free of charge. The dealer may also inspect the oil pan for metal debris, and replace the engine if necessary. Repairs will be performed free of charge. Owner notification letters were mailed April 8, 2026. Owners may contact Nissan's customer service at 800-647-7261. Nissan's numbers for this recall are R25E2 and R25E3. This recall expands previous NHTSA recall number 25V437. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning February 27, 2026.
ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL · 25V437000
2025-06-27
Nissan North America, Inc. (Nissan) is recalling certain 2021-2024 Rogue, 2019-2020 Altima, 2019-2022 Infiniti QX50, and 2022 Infiniti QX55 vehicles equipped with 3-cylinder 1.5L or 4-cylinder 2.0L variable compression turbo (VC-Turbo) engines. The engine bearings may have manufacturing defects that can lead to engine failure.
Consequence: Engine failure increases the risk of a crash. A bearing failure may cause a breach in the engine block, allowing hot oil to be discharged, increasing the risk of an engine fire.
Remedy: Dealers will reprogram the engine control module (ECM) software, free of charge. Owner letters were mailed April 8, 2026. Owners may contact Nissan's customer service at 800-647-7261 or Infiniti's customer service at 1-800-662-6200. Nissan's numbers for this recall are R25A8/A9 and R25B1/B2.
SEAT BELTS:PRETENSIONER · 24V156000
2024-02-28
Nissan North America, Inc. (Nissan) is recalling certain 2023 Rogue vehicles. The driver and front passenger seat belt pretensioners may have been incorrectly manufactured, which can cause the seat belts to not properly restrain occupants. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection," 209, "Seat Belt Assemblies," and 210 "Seat Belt Assembly Anchorages."
Consequence: Improperly restrained occupants have an increased risk of injury during a crash.
Remedy: Dealers will replace the front seat belt assemblies, as necessary, free of charge. Owner notification letters were mailed April 26, 2024. Owners may contact Nissan customer service at 1-800-867-7669. Nissan's number for this recall is PD105.
AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE · 24V154000
2024-02-27
Nissan North America, Inc. (Nissan) is recalling certain 2024 Titan, Frontier, Infiniti QX60, Pathfinder, 2023-2024 Sentra, Versa, Kicks, Infiniti QX50, and 2023 Rogue vehicles. Due to a manufacturing issue, the driver's air bag inflator may absorb moisture, and cause the air bag to deploy improperly.
Consequence: An air bag that deploys improperly may not protect the driver as intended during a crash, increasing the risk of injury.
Remedy: Dealers will replace the front driver's air bag assembly, free of charge. Owner notification letters were mailed April 10, 2024. Owners may contact Nissan customer service at 1-800-867-7669. Nissan's numbers for this recall are PD103, PD104, and PMA34.
SEAT BELTS:CRITICAL FASTENERS · 23V374000
2023-05-25
Nissan North America, Inc. (Nissan) is recalling certain 2023 Nissan Rogue vehicles. The fastener in the rear seat belt anchor attachment points may not have been tightened properly and can loosen over time.
Consequence: A loose rear seat belt anchor fastener may not properly restrain an occupant in the event of a crash, increasing the risk of injury.
Remedy: Dealers will inspect and tighten the rear seat belt anchor bolts. Additionally, dealers will apply warning labels to the seat belt attachment points to indicate the bolt size and torque value required for any future seat belt repair. Repairs will be performed free of charge. Owner notification letters are expected to be mailed July 14, 2023. Owners may contact Nissan's customer service at 1-800-867-7669. Nissan's number for this recall is PC978, PC979.
SEATS:CRITICAL FASTENERS · 23V268000
2023-04-13
Nissan North America, Inc. (Nissan) is recalling certain 2023 Rogue, Pathfinder, and Infiniti QX60 vehicles. The driver's powered seat may not be fully secured to the seat frame, causing the seat frame welds to detach from the rear inboard seat bracket.
Consequence: An unsecured seat with broken welds may not properly restrain an occupant during a crash, increasing the risk of injury.
Remedy: Dealers will inspect the driver's seat rail clearance, and if necessary, replace the driver's seat cushion frame, free of charge. Owner notification letters are expected to be mailed June 10, 2023. Owners may contact Nissan's customer service at 1-800-867-7669. Nissan's number for this recall is PC966, PC967.
Size-standard part numbers — verify your connector type before buying. Rear blades are model-specific; check the package's vehicle list.
Fuel economy figures are EPA data via fueleconomy.gov (median across matching trims). Performance figures are compiled estimates for the 2023 Nissan Rogue 1.5L I3 Turbo and can vary by trim.
🔧 Database maintained under the daily editorial review of Chris Hackleman · Master Technician · 20+ years and Jeff Moore · Master Lexus & Toyota Mechanic · 20+ years.