1967 PLYMOUTH FURY

225ci I6RWDAUTOMATICgas
5-Year Cost of Ownership
$35,153 maintenance + known platform issues
~$7,031/yr · 590¢/mile equivalent · $31,743 maintenance + $2,710 expected platform issues
Compare this engine
vs
318ci V8
Common Problems & Known Issues

The 1967 Plymouth Fury is a full-size Mopar C-body with proven drivetrains but typical late-60s quality control issues. Most problems stem from age-related deterioration rather than design flaws, though certain weaknesses exist across the platform.

Timing Chain Stretch and Failure (V8 engines)

Common · high severity
Typical onset: 80,000-120,000 mi
Symptoms: Engine rattling at cold start that quiets when warm, Rough idle and poor timing adjustment, Backfiring through carburetor, Hard starting when hot, Check timing marks - they'll be significantly off if chain is stretched
Fix: Replace timing chain, gears, and front seal while you're in there. Budget 4-6 hours for a straightforward swap on 318/383 engines, closer to 6-8 hours on 440s due to tighter engine bay. Always replace the timing tab and verify TDC marks afterward. Original single-row chains rarely made it past 100k without stretch.
Estimated cost: $450-850

Torsion Bar Anchor Corrosion and Failure

Occasional · high severity
Symptoms: Severe front-end sag on one or both sides, Clunking from front suspension over bumps, Visible rust perforation in lower control arm anchor pockets, Uneven ride height that can't be adjusted out
Fix: The torsion bar anchors in the lower control arms rust through, especially in salt-belt cars. Requires replacement of lower control arms, torsion bars, and associated bushings. Figure 8-10 hours for both sides including alignment. This is a safety-critical repair - suspension collapse is possible. Inspect carefully on any purchase.
Estimated cost: $1,200-2,200

Carter AFB/AVS Carburetor Float Bowl Leaks

Common · medium severity
Symptoms: Raw fuel smell in garage or after shutdown, Fuel dripping from carburetor base or externally visible on intake, Hard starting after sitting overnight (bowl drains down), Flooding and black smoke on cold starts
Fix: The original Carter carbs used gaskets and seals that harden and fail over 50+ years. A proper rebuild with modern gasket kit takes 3-4 hours including removal, rebuild, and re-tuning. Many shops will recommend replacement with an Edelbrock (same basic design, new parts) instead of rebuilding crusty originals. Rebuilding is cheaper but replacement ensures long-term reliability.
Estimated cost: $350-650 rebuild, $650-950 replacement

Drum Brake Wheel Cylinder Seepage

Common · medium severity
Symptoms: Fluid on inside of rear wheels or drums, Soft or spongy brake pedal that gets worse over time, Reduced braking effectiveness, Low brake fluid level requiring frequent top-ups
Fix: Original single-piston wheel cylinders leak as rubber cups deteriorate. Replace all four wheel cylinders, shoes, hardware, and perform complete brake flush. Budget 4-5 hours for rear brake overhaul. These cars have adequate but not impressive braking to begin with - leaking cylinders make them dangerous. Many owners convert to front disc brakes ($1,500-2,500 additional) for improved stopping power.
Estimated cost: $450-750

Upper Ball Joint Wear (Front Suspension)

Occasional · high severity
Typical onset: 70,000-110,000 mi
Symptoms: Steering wander and poor returnability, Clunking over bumps from front end, Excessive play in steering wheel, Uneven tire wear on inside or outside edges, Visual inspection shows vertical movement when prying on tire
Fix: The upper ball joints are load-bearing on these C-bodies and wear faster than lowers. Replaceable separately on most models, but if the bushings are also shot, replace the entire upper control arm assembly. Figure 3-4 hours per side plus alignment. Neglected ball joints can separate, causing complete loss of steering control.
Estimated cost: $500-900 both sides

Fuel Sending Unit Failure

Occasional · low severity
Symptoms: Fuel gauge reading empty when tank is full or vice versa, Gauge fluctuating wildly with vehicle movement, Gauge pinned at one extreme regardless of fuel level, Intermittent gauge operation
Fix: The float arm in the sending unit corrodes or the resistance wire fails after decades. Requires fuel tank drop for access. Figure 2-3 hours for tank removal, sending unit replacement, and reinstallation. Good time to inspect and clean or replace fuel tank, lines, and filter if doing this job. Low severity but annoying for daily use.
Estimated cost: $350-600

Heater Core Leakage

Occasional · medium severity
Symptoms: Sweet coolant smell inside cabin with heater on, Foggy windshield that's greasy to the touch, Wet passenger-side carpet, Coolant loss with no external leaks visible, Steam from defrost vents
Fix: Original copper/brass heater cores corrode through. Access requires major dash disassembly on these cars - budget 6-8 hours labor for heater core replacement. Many techs will flush and bypass temporarily ($100-150, 1 hour) for summer months, but full repair requires the dash work. Use a modern aluminum core for longevity.
Estimated cost: $650-1,100

Voltage Regulator and Alternator Failures (If Equipped)

Common · medium severity
Symptoms: Dim headlights at idle, Battery repeatedly going dead, Ammeter showing discharge while driving, Flickering dash lights, Overcharging (above 15 volts) or undercharging (below 13 volts)
Fix: Early '67s may have generators; most have alternators with external voltage regulators. Both the alternator brushes and the electromechanical voltage regulator fail regularly on 55+ year old units. Diagnosis takes 0.5 hours; alternator rebuild or replacement is 1-2 hours. External regulator replacement is 0.5 hours. Test both components - often one fails and damages the other. Modern solid-state regulators are reliable upgrades.
Estimated cost: $250-550
Owner tips
  • Inspect all rubber components (fuel lines, brake hoses, suspension bushings) immediately on purchase - 50+ years means everything is aged out regardless of mileage
  • The 318 and 383 are bulletproof engines if timing chain is maintained; avoid 225 Slant-6 models as parts availability is declining
  • Budget for complete brake system overhaul including lines if buying a car that's been sitting - these had marginal braking when new
  • Undercoating and frame inspection is critical - C-body frames rust in rear leaf spring mounts and front torsion bar crossmember
  • Keep spare points, condenser, and coil in trunk - these ignition systems are simple but components fail unpredictably
Buy a solid, driving example with maintenance records - avoid projects unless you're experienced with 60s Mopars, as restoration costs quickly exceed value on non-performance models.
AI-assisted summary drawn from NHTSA recall data, our labor-times database, and platform knowledge. Not a substitute for a pre-purchase inspection on a specific vehicle.
593 jobs across 17 categories
Building an app?
Free API access to all this data — 50 requests/day, no card required.
Get an API key →
Run a shop?
Manage repairs, estimates, and customers with ShopBase — $249/mo, all features included. Built by the same team.
Try ShopBase →