1976 PLYMOUTH FURY

360ci V8RWDAUTOMATICgas
5-Year Cost of Ownership
$40,368 maintenance + known platform issues
~$8,074/yr · 670¢/mile equivalent · $37,703 maintenance + $1,965 expected platform issues
Compare this engine
vs
225ci I6
vs
318ci V8
Common Problems & Known Issues

The 1976 Plymouth Fury is a full-size C-body Mopar with robust LA and B-series V8s (or the slant-six). Most issues stem from age rather than inherent design flaws—expect rubber, linkages, and emission controls to be worn after nearly 50 years.

Timing Chain Stretch and Wear (V8 engines)

Common · high severity
Typical onset: 80,000-150,000 mi
Symptoms: rattling on cold start that quiets after warmup, rough idle or erratic timing, backfiring through carburetor, difficulty starting when hot
Fix: Replace timing chain, gears, and tensioner as a set. Plan 4-6 hours labor for front cover removal, gasket replacement, and timing adjustment. Non-interference engine, so usually no valve damage, but delay leads to jumped timing and no-start.
Estimated cost: $400-800

Lean Burn Ignition System Failures (California and late '76 models)

Common · medium severity
Symptoms: intermittent stalling or no-start, bucking and surging under light throttle, check engine light (if equipped), poor fuel economy and hesitation
Fix: The computer control module and pickup coil in distributor are notorious. Most techs convert to conventional electronic ignition (Mopar Performance kit or pre-'76 distributor swap). Troubleshooting original system is frustrating. Conversion takes 2-3 hours.
Estimated cost: $200-500

Carburetor Issues (Carter ThermoQuad and Holley 2-bbl)

Common · medium severity
Symptoms: flooding and fuel leaks from warped phenolic body (ThermoQuad), hard starting when warm, black smoke and rich running, hesitation off idle
Fix: ThermoQuad plastic bodies warp with age and heat—many swap to Edelbrock or Holley replacement. Holley 2-bbl needs periodic rebuild. Full rebuild or replacement takes 2-4 hours including tuning.
Estimated cost: $300-700

Torsion Bar Suspension Sag and Worn Bushings

Common · low severity
Typical onset: 60,000-100,000 mi
Symptoms: front end sits low, headlights point upward, wandering and vague steering, clunking over bumps, uneven tire wear
Fix: Torsion bars rarely break but adjusters seize and lower control arm bushings disintegrate. Full front-end refresh (bushings, ball joints, adjuster service) runs 6-8 hours. Alignment mandatory afterward.
Estimated cost: $600-1,200

Transmission Kickdown Linkage Misadjustment (TorqueFlite A727/A904)

Occasional · medium severity
Symptoms: delayed or no downshift on WOT, trans slipping or flaring between gears, late upshifts and lugging, burnt transmission fluid smell
Fix: Kickdown rod or cable comes out of adjustment or wears. Simple adjustment takes 0.5 hours, but delayed diagnosis leads to clutch/band damage requiring trans rebuild (10-15 hours). Check and adjust every service.
Estimated cost: $50-150 adjustment, $1,500-2,500 rebuild if damaged

Fuel Tank and Sending Unit Corrosion

Occasional · medium severity
Symptoms: inaccurate or stuck fuel gauge, fuel leaks from tank seams, rust flakes in fuel filter, fuel pump starvation
Fix: Steel tanks rust through after decades, especially if stored outdoors. Sending units seize. Tank drop and replacement takes 3-4 hours; sending unit alone 2 hours. Many upgrade to aftermarket poly tank.
Estimated cost: $400-900

Power Steering Gear Box Leaks and Slop

Occasional · low severity
Typical onset: 80,000-120,000 mi
Symptoms: power steering fluid leaks at sector shaft seal, excessive play at center (more than 2 inches wheel movement), groaning when turning, wandering on highway
Fix: Chrysler recirculating-ball boxes develop sector shaft seal leaks and internal wear. Adjustment helps temporarily (0.5 hours), but rebuilt/reman box swap is long-term fix (3-4 hours). Alignment needed.
Estimated cost: $300-700
Owner tips
  • Change timing chain proactively around 100k if unknown—cheap insurance against a tow bill
  • Ditch Lean Burn if it's acting up; conventional ignition is more reliable and easier to tune
  • Use quality fuel filters and check tank condition—internal rust kills fuel pumps and carbs
  • Keep kickdown linkage adjusted and fluid fresh in the TorqueFlite; they're bulletproof if maintained
  • Grease front-end fittings every oil change—these suspensions last forever with lube, die quickly without
Buy one if you're comfortable with carburetors and can wrench—parts are cheap, engines are stout, but 50-year-old emissions and ignition tech will test your patience.
AI-assisted summary drawn from NHTSA recall data, our labor-times database, and platform knowledge. Not a substitute for a pre-purchase inspection on a specific vehicle.
593 jobs across 17 categories
Building an app?
Free API access to all this data — 50 requests/day, no card required.
Get an API key →
Run a shop?
Manage repairs, estimates, and customers with ShopBase — $249/mo, all features included. Built by the same team.
Try ShopBase →