1998 TOYOTA 4RUNNER

Typical onset: 80,000-150,000 mi

Symptoms: White smoke from exhaust on cold start, Coolant consumption without visible leaks, Overheating under load, Milky oil on dipstick or cap, Rough idle and misfires

Fix: The 3.0L 3VZ-E engine is notorious for blown head gaskets between cylinders 4 and 5. If caught early, it's a head gasket job (12-16 hours labor). If ignored, overheating warps the heads or cracks the block, requiring full engine rebuild or replacement (25-35 hours). Many owners opt for a used 3.4L swap instead of rebuilding the 3.0L.

Estimated cost: $1,800-3,200 for gaskets alone; $4,500-7,500 for rebuild or replacement

Typical onset: 60,000-100,000 mi

Symptoms: Clunking over bumps from front suspension, Wandering steering or loose feel, Uneven tire wear on inside edges, Grease boot torn or missing, Visible play when prying on tire at 6 and 12 o'clock

Fix: Toyota's lower ball joints from this era are notoriously weak and non-serviceable—they're pressed into the control arm. Replacing both lower ball joints requires pressing out old joints and installing new ones, or replacing entire lower control arms (easier for DIY). 3-5 hours labor for both sides. Alignment required after. Do NOT ignore—a separated ball joint causes total loss of control.

Estimated cost: $600-1,200 depending on parts choice and alignment

Typical onset: 120,000-180,000 mi

Symptoms: Pink or milky transmission fluid, Transmission slipping or delayed engagement after radiator work, Coolant in transmission pan, Engine overheating combined with transmission issues

Fix: The factory transmission cooler is integrated into the radiator. When the internal separator fails, coolant and ATF mix—called 'strawberry milkshake of death.' This destroys the transmission within days if driven. Requires radiator replacement, full transmission flush (or rebuild if contaminated long enough), and external cooler installation to prevent recurrence. 8-12 hours if trans is salvageable; 15-25 hours if rebuild needed.

Estimated cost: $800-1,500 for radiator and flush; $2,500-4,000 if transmission damaged

Symptoms: Visible surface rust progressing to flaking/scaling on frame, Rust perforation near rear leaf spring mounts, Sagging rear end or misaligned body, Failed state inspection in rust-belt states

Fix: Not mileage-dependent—climate and prior use matter most. Rust-belt 4Runners often have compromised frames, especially rear crossmember and outriggers where leaf springs mount. Minor surface rust can be wire-brushed and coated; structural rust requires welding in new steel sections or frame replacement (30-50 hours). Inspect thoroughly before purchase—many are too far gone to fix economically.

Estimated cost: $500-1,500 for preventive treatment; $3,000-8,000+ for welded repairs

Typical onset: 90,000 mi intervals

Symptoms: No symptoms until it fails—then catastrophic engine damage, Slight ticking from timing cover if belt is glazed, Coolant seepage from water pump weep hole

Fix: The 3.4L 5VZ-FE is an interference engine—if the belt breaks, valves hit pistons causing $3,000-5,000 in damage. Toyota spec is 90k miles; many techs recommend 60k in severe climates. Always replace water pump, tensioner, and idler pulleys with the belt (they're behind the same covers). 4-6 hours labor. The 2.7L I4 is non-interference and less critical, but still needs service.

Estimated cost: $600-1,000 for full timing service with water pump

Typical onset: 100,000-180,000 mi

Symptoms: Ticking or tapping from engine bay that increases with RPM, Exhaust smell in cabin, Visible soot streaks on manifold, Failed emissions test due to pre-cat O2 sensor reading

Fix: Exhaust manifolds crack between ports due to heat cycling, and manifold studs often break off in the head when removing. Common on all engines but especially the 3.4L. If caught early, it's a gasket and manifold replacement (3-5 hours per side). Broken studs require drilling and extraction, adding 2-4 hours. Aftermarket headers are a popular permanent fix.

Estimated cost: $400-900 per side; $800-1,400 if studs break