🌍 International coverage, work in progress. This Russian-market vehicle is part of our hand-curated international catalog. We are filling in labor times, torque specs and fluids as fast as we can verify them, so some numbers may be missing or marked estimated for now. Do you work on these vehicles in the EU, Russia, or the JDM scene? Help us get it right: send real shop times or corrections to [email protected], or request the data you need and it joins the verification queue.

2010 VOLKSWAGEN TOUAREG

4.2L V8AWDAUTOMATICgasCGRA
Be the first sponsor for this vehicle

For $99, we generate the full set of step-by-step repair procedures for this exact vehicle. Free for everyone, forever, with your name on every one.

Sponsor — $99
Dead battery / stuck in Park? Emergency neutral procedure for this Touareg
Every control module on the 2004-2010 Volkswagen Touareg — where it lives, replacement time, and what it takes to program a replacement. Modules marked dealer / factory tool won't work after a part swap alone — budget for programming.
Transmission Control Module (TCM)3.5 hr R&Rdealer / factory tool +1.0 hr▸ programming details
📍 Inside transmission valve body (6-speed auto) or external on transmission case (Aisin 8-speed on later models)
🔧 VAS 5051/5052 or VCDS
⚠️ Requires transmission pan removal and fluid change; adaptation procedures mandatory
All-Wheel Drive Control Module (4Motion/AWD)2.0 hr R&Raftermarket tool +0.5 hr▸ programming details
📍 Under vehicle, mounted to transfer case or near rear differential
🔧 VCDS
⚠️ Controls torque distribution; adaptation for clutch pack calibration
ABS/ESP Control Module (ABS)1.5 hr R&Raftermarket tool +0.5 hr▸ programming details
📍 Engine compartment, mounted to ABS hydraulic unit on left side near brake master cylinder
🔧 VCDS or Autel
⚠️ Brake bleeding required after replacement; coding for wheel size and tire specifications
Fuel Pump Control Module (Fuel Pump Module)1.5 hr R&Rrelearn only +0.2 hr▸ programming details
📍 Under vehicle, near fuel tank or integrated into fuel pump assembly
🔧 VCDS
⚠️ Basic adaptation only; primarily on diesel models
Central Convenience Control Module (Comfort Module)1.5 hr R&Raftermarket tool +0.8 hr▸ programming details
📍 Behind driver side lower dashboard panel or under driver seat
🔧 VCDS or Autel
⚠️ Controls windows, locks, lighting; extensive long-coding for feature configuration
Gateway Control Module (Gateway)1.2 hr R&Raftermarket tool +0.5 hr▸ programming details
📍 Behind dashboard, center area near HVAC or under driver side dash
🔧 VCDS
⚠️ CAN bus hub; coding for installed modules and options
Door Control Module (Door Module)1.2 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Inside door panel, typically driver and front passenger doors
🔧 VCDS
⚠️ Controls windows, mirrors, locks per door; window auto-up/down relearn required
Engine Control Module (ECM)1.2 hr R&Rdealer / factory tool +0.8 hr▸ programming details
📍 Engine compartment, left side near firewall or under intake manifold depending on engine
🔧 VAS 5051/5052 or VCDS
⚠️ Immobilizer adaptation required; V8 and V10 TDI require intake manifold removal
Immobilizer Control Module (Immo)1.2 hr R&Rdealer / factory tool +1.5 hr▸ programming details
📍 Integrated into steering column control module or separate module near ignition switch
🔧 VAS 5051/5052
⚠️ Key matching and ECM pairing required; EEPROM programming may be needed for used modules
Tailgate Control Module (Tailgate Module)1.0 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Inside tailgate, behind interior trim panel
🔧 VCDS
⚠️ Only on models with power liftgate; calibration for open/close limits
Airbag Control Module (ACM)1.0 hr R&Rdealer / factory tool +0.5 hr▸ programming details
📍 Center console tunnel, under center armrest or behind center trim panel
🔧 VAS 5051/5052
⚠️ Crash data must be cleared; some aftermarket tools can code but dealer tool recommended
Steering Angle Sensor Module (Steering Sensor)1.0 hr R&Raftermarket tool +0.5 hr▸ programming details
📍 Steering column, below steering wheel
🔧 VCDS
⚠️ Steering angle calibration mandatory after replacement; wheel alignment required
Headlight Range Control Module (Headlight Control)1.0 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Behind headlight assembly or integrated into headlight (Xenon/AFS models)
🔧 VCDS
⚠️ Adaptive lighting models require calibration; left and right modules on AFS-equipped vehicles
Climate Control Module (Climatronic)1.0 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Behind center dashboard climate control panel
🔧 VCDS
⚠️ Basic adaptation for sensor calibration
Air Suspension Control Module (Air Susp)1.0 hr R&Raftermarket tool +0.5 hr▸ programming details
📍 Rear cargo area, left side panel or under rear seat
🔧 VCDS
⚠️ Only on models with air suspension; calibration and ride height adaptation required
Instrument Cluster Control Module (Cluster)0.8 hr R&Rdealer / factory tool +0.8 hr▸ programming details
📍 Behind instrument cluster in dashboard
🔧 VAS 5051/5052
⚠️ Mileage programming required and legally restricted; immobilizer data transfer needed
Park Distance Control Module (PDC)0.8 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Rear cargo area, behind left or right side trim panel
🔧 VCDS
⚠️ Sensor calibration may be needed
Radio/Navigation Control Module (Radio/Nav)0.8 hr R&Raftermarket tool +0.5 hr▸ programming details
📍 Center dashboard, integrated into head unit
🔧 VCDS
⚠️ Anti-theft code may be required; coding for vehicle-specific features and CAN gateway
Seat Memory Control Module (Seat Module)0.8 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Under driver and/or passenger seat
🔧 VCDS
⚠️ Only on models with memory seats; separate modules for driver and passenger
Trailer Control Module (Trailer Module)0.8 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Rear cargo area, left side or near hitch receiver
🔧 VCDS
⚠️ Only on models with factory trailer package
Aftermarket tool coverage varies by software version and vehicle build — treat "aftermarket tool" rows as "usually possible" and verify against your tool maker's coverage list before promising a customer. Spot a wrong location or hour? Tell us — corrections ship fast here.
🔧 Database maintained under the daily editorial review of Chris Hackleman · Master Technician · 20+ years.
Stuck on a repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
Building an app?
Free API access to all this data — 10 requests/day, no card required.
Get an API key →
Run a shop?
Manage repairs, estimates, and customers with ShopBase — $249/mo, all features included. Built by the same team.
Try ShopBase →