Blower Motor

Replace the blower motor assembly in a 2008 Dodge Viper, located in the HVAC housing on the passenger side of the firewall.

Warnings

Tools required

Parts

• Blower motor assembly × 1 — Use OEM specification
• Blower motor resistor (if damaged) × 1 — Use OEM specification

Preparation

1. Park vehicle on level surface and engage parking brake
2. Turn ignition to OFF position and remove key
3. Open hood and disconnect negative battery terminal to prevent accidental blower motor activation
4. Allow vehicle to cool if recently driven, as engine heat radiates to the passenger footwell area
5. Move passenger seat fully rearward for easier access to lower dash area

Procedure

1. 1

   Access passenger side lower dash area
   Working from the passenger footwell, identify the lower dash panel below the glove box. Remove the push-pin fasteners securing the lower dash panel. The panel is held by approximately 4-6 push-pins along the upper edge and sides. Gently pull the panel downward and away to expose the HVAC housing and blower motor area.
2. 2

   Locate blower motor assembly
   Using a flashlight, locate the blower motor housing on the passenger side of the firewall, toward the lower right section of the HVAC unit. The motor is a cylindrical assembly with an electrical connector on the side and cooling air intake slots. Identify the wiring harness connector and mounting fasteners.
3. 3

   Disconnect blower motor electrical connector
   Press the locking tab on the blower motor electrical connector and pull the connector straight off the motor terminals. The connector has a positive lock that must be released before removal. Ensure no stress is placed on the wiring harness during disconnection.
4. 4

   Remove blower motor mounting screws
   Using a 7mm socket with a 3-inch extension, remove the 3 screws securing the blower motor to the HVAC housing. The screws are positioned around the perimeter of the motor mounting flange. Support the motor with one hand as you remove the final screw to prevent it from falling.
   Torque spec

   Blower Motor Screws4 Nm (3 lb-ft)
5. 5

   Extract blower motor assembly
   Carefully rotate the blower motor assembly to clear the HVAC housing opening. The motor and fan cage assembly may need to be tilted slightly to navigate past surrounding components. Pull the motor straight out from the housing, taking care not to contact the fan cage against the housing edges, which could damage the fan blades.
6. 6

   Inspect blower motor resistor
   With the blower motor removed, inspect the blower motor resistor, which is mounted on the HVAC housing near the motor opening. Check for signs of burning, melting, or corrosion on the resistor terminals and connectors. If the resistor shows damage, remove its 2 mounting screws using a 7mm socket and disconnect its electrical connector for replacement.
   Torque spec

   Blower Motor Resistor Screws2 Nm (1.5 lb-ft)
7. 7

   Inspect HVAC housing and clean area
   Before installing the new motor, inspect the HVAC housing opening for debris, leaves, or obstructions. Remove any debris that could interfere with motor operation or airflow. Check the rubber seal around the motor mounting area and ensure it is intact and properly seated in the housing groove.
8. 8

   Install new blower motor
   Position the new blower motor assembly at the HVAC housing opening. Rotate and tilt the motor as needed to align the motor flange with the mounting surface, ensuring the fan cage clears all internal housing components. Push the motor firmly into position until the mounting flange is flush against the housing.
9. 9

   Install blower motor mounting screws
   Install the 3 blower motor mounting screws by hand, starting each screw before tightening. Using a torque wrench with a 7mm socket, tighten the screws in a star pattern to 4.0 Nm (3.0 lb-ft). This ensures even clamping force and proper sealing of the motor to the housing.
   Torque spec

   Blower Motor Screws4 Nm (3 lb-ft)
10. 10

    Reconnect electrical connector
    Push the electrical connector onto the blower motor terminals until the locking tab clicks into place. Verify the connector is fully seated and the lock is engaged by gently pulling on the connector body. Ensure the wiring harness has adequate slack and is not pinched or stressed.
11. 11

    Test blower motor operation
    Before reinstalling the lower dash panel, reconnect the negative battery terminal. Turn the ignition to the ON position (engine off) and test the blower motor at all speed settings using the climate control panel. Verify smooth operation with no unusual noises, vibration, or binding. Check that airflow is consistent at all speeds.
12. 12

    Reinstall lower dash panel
    Position the lower dash panel back into place below the glove box. Align the panel with the mounting points and press firmly to engage all push-pin fasteners. Verify the panel is secure and flush with the surrounding dash surfaces.

Reassembly

1. Ensure all electrical connectors are fully seated with locking tabs engaged
2. Verify no tools or debris remain in the passenger footwell area
3. Return passenger seat to desired position

Verification

• Start the engine and test the blower motor at all speed settings (low, medium-low, medium-high, high)
• Verify consistent airflow from all vents with no unusual noises or vibration
• Confirm proper operation in all climate control modes (heat, vent, A/C, defrost)
• Check for air leaks around the blower motor mounting area by listening for whistling sounds at high blower speed

Related trouble codes on this vehicle

Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.

Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →

More procedures for this vehicle