Free API
8.4L V10•RWD•MANUAL•gas
Founding sponsor spot is openYour name on every procedure for this vehicle, permanently.Sponsor — $99 →
engine

Camshaft R&R

for 2017 Dodge Viper 8.4L V10 · RWD
Difficulty
Expert
Time
11.7 h
Tools
17
Steps
18
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

Complete removal and reinstallation of intake and exhaust camshafts on the 2008 Dodge Viper 8.4L V10 engine, including valve train disassembly, timing component removal, and camshaft bearing cap service.

Warnings

⚠️The engine must be cold before beginning this procedure. Hot components can cause severe burns.
⚠️Camshaft bearing caps must be loosened and tightened in the specified sequence only. Failure to follow sequence will damage bearing caps and cylinder head.
⚠Camshaft bearing caps are directional and position-specific. Mark each cap with its cylinder number and orientation before removal.
⚠Do not rotate the engine with camshafts removed. Valve-to-piston contact will occur and cause severe engine damage.
⚠Camshaft bearing cap bolts are torque-to-yield and must be replaced. Do not reuse old bolts.
ℹ️This procedure requires engine oil and filter change upon completion.

Tools required

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Fluids

  • engine_oil — 11 qt

Preparation

  1. Park vehicle on level ground and engage parking brake.
  2. Ensure engine is completely cold (ideally overnight cool-down).
  3. Disconnect negative battery cable and secure away from battery post.
  4. Remove engine cover by pulling upward on perimeter clips.
  5. Drain engine oil completely and remove oil filter.
  6. Remove engine air intake system from throttle body to airbox.
  7. Label and disconnect all vacuum lines, electrical connectors, and fuel lines from intake manifold and valve covers.
  8. Relieve fuel system pressure by removing fuel pump relay and cranking engine until it fails to start.
  9. Support engine from above using engine support fixture or hoist with load leveler.
  10. Photograph timing chain and camshaft sprocket alignment marks before disassembly.

Procedure

  1. 1
    Remove valve covers
    Remove ignition coil connectors and bolts, then remove all 10 ignition coils (5 per cylinder head). Remove valve cover bolts (10 per side) and carefully lift valve covers straight up to avoid damaging gasket sealing surfaces. Remove and discard valve cover gaskets and bolt grommets.
  2. 2
    Rotate engine to TDC cylinder 1
    Using a socket on the crankshaft bolt, rotate the engine clockwise until cylinder 1 is at top dead center on the compression stroke. Verify timing marks on camshaft sprockets align with marks on timing chain per factory service manual, and confirm crankshaft is at the factory-specified TDC index position for cylinder 1. Mark the timing chain-to-sprocket relationship with paint pen on both intake and exhaust camshaft sprockets.
  3. 3
    Lock timing chain tensioners
    Access and lock the primary timing chain tensioner(s) per the factory service manual to retain chain tension. Verify tensioner location and locking method against OEM documentation for this engine before proceeding. This prevents chain slack when camshaft sprockets are removed.
  4. 4
    Remove camshaft position sensors
    Disconnect electrical connectors from the camshaft position sensor(s). Verify the exact number and location of CMP sensors against the factory service manual for this engine. Remove the sensor mounting bolts and carefully withdraw sensors from cylinder heads. Note the O-ring position and condition.
  5. 5
    Secure camshaft sprockets and remove retaining bolts
    Install camshaft holding tool to prevent sprocket rotation. Remove the center bolt from each camshaft sprocket. Verify the exact number of camshafts and sprockets against the factory service manual for this engine's valvetrain configuration. Keep bolts organized by position. Carefully slide sprockets forward off camshafts while supporting timing chain with wire to prevent chain from falling into timing cover.
  6. 6
    Remove rocker arms and hydraulic lash adjusters
    Remove valvetrain components (rocker arms, followers, and/or hydraulic lash adjusters) per the factory service manual for this engine's specific valvetrain design, keeping all components organized by exact position for reinstallation. Keep adjusters organized by cylinder and valve position (intake/exhaust). Do not allow adjusters to drain down; store upright.
  7. 7
    Mark and prepare camshaft bearing caps
    Using a paint pen, clearly mark each camshaft bearing cap with its cylinder number, bank identifier (left/right), and orientation arrow pointing toward front of engine. The caps are machined in place and are not interchangeable. Verify all caps are marked before loosening any fasteners.
  8. 8
    Loosen camshaft bearing cap bolts in sequence
    Remove the camshaft thrust plate bolts and thrust plate at the front of the block per the factory service manual. This engine uses in-block camshaft bearings with no removable bearing caps. First pass: loosen each bolt 1/4 turn. Second pass: loosen each bolt an additional 1/2 turn. Third pass: remove bolts completely. Perform this for intake camshaft bearing caps first, then exhaust camshaft bearing caps. There are approximately 10 bearing cap bolts per camshaft.
  9. 9
    Remove camshaft bearing caps and camshafts
    Carefully withdraw the single camshaft straight forward and out of the front of the engine block, supporting the shaft to avoid damaging the in-block bearings. Inspect camshaft journals and lobes for scoring, discoloration, or damage. Inspect camshaft bearing journals and cylinder head bearing surfaces for scoring, discoloration, or damage.
  10. 10
    Inspect and prepare cylinder head bearing surfaces
    Thoroughly clean all camshaft bearing surfaces in cylinder head using lint-free shop towels and appropriate solvent. Inspect bearing surfaces for wear, scoring, or damage. Check that oil feed passages in head are clear. If installing used camshafts, verify bearing clearances using Plastigage per manufacturer specifications before final assembly.
  11. 11
    Install camshafts
    Lubricate all camshaft bearing journals liberally with clean engine assembly lube or 0W-40 engine oil. Carefully slide the camshaft into the block bore, lubricating journals and lobes, and rotate as needed to ease it past the bearings without damaging them. Install the camshaft thrust plate. Verify camshafts rotate freely in their bearings without binding.
  12. 12
    Install camshaft bearing caps and torque in sequence
    Apply light coat of clean engine oil to bearing cap surfaces. Install all bearing caps in their exact original positions, verifying orientation marks face forward. Install and torque the camshaft thrust plate bolts to the factory specification. This engine has no camshaft bearing caps; camshaft axial location is controlled by the thrust plate. Complete intake camshaft caps fully before moving to exhaust camshaft caps.
  13. 13
    Verify camshaft endplay and rotation
    Using a dial indicator against the camshaft nose, measure camshaft endplay controlled by the thrust plate. Endplay must be within the factory-specified range per the service manual. Rotate camshafts by hand to verify smooth operation without binding. Check that camshaft timing marks align properly for TDC cylinder 1 position.
  14. 14
    Install hydraulic lash adjusters and rocker arms
    Reinstall the hydraulic roller lifters into their original block bores, followed by the pushrods and rocker arms in their exact original positions, per the factory service manual. Verify each rocker arm moves freely and seats properly on both valve tip and lash adjuster.
  15. 15
    Install camshaft sprockets and timing chain
    Install the camshaft sprocket and timing chain aligning the crankshaft and camshaft timing marks per the factory service manual, matching the painted marks made during disassembly. Install the camshaft sprocket bolt(s) and torque to the factory-specified value per the service manual while holding the camshaft against rotation.
  16. 16
    Remove timing chain tensioner pins and verify timing
    Remove tensioner locking pins from both cylinder heads, allowing tensioners to apply proper chain tension. Rotate engine two complete revolutions clockwise and verify all timing marks realign at TDC cylinder 1. Confirm paint marks on chain and sprockets still align. Install tensioner access plugs with new sealing washers if required.
  17. 17
    Install camshaft position sensors
    Install new O-ring(s) on the camshaft position sensor(s) lubricated with clean engine oil, install into their bore(s), secure with mounting bolts, and reconnect the electrical connector(s). Verify sensor count against the factory service manual.
  18. 18
    Install valve covers
    Install new valve cover gaskets and new bolt grommets into valve covers. Position valve covers onto cylinder heads, ensuring gaskets seat properly in grooves. Install valve cover bolts and torque in cross-pattern sequence to the factory-specified value per the service manual. Do not overtighten as this will damage gaskets. Reinstall ignition coils and torque the mounting bolts to the factory-specified value per the service manual. Reconnect ignition coil electrical connectors.

Reassembly

  1. Reinstall all vacuum lines, electrical connectors, and fuel lines to intake manifold and valve covers per labeling made during disassembly.
  2. Reinstall engine air intake system from throttle body to airbox.
  3. Reinstall fuel pump relay.
  4. Install new engine oil filter and fill engine with 11 quarts of 0W-40 full synthetic engine oil.
  5. Reinstall engine cover by pressing firmly on perimeter clips.
  6. Reconnect negative battery cable.
  7. Remove engine support fixture or hoist.

Verification

  • Start engine and allow to idle. Listen for unusual valve train noise or ticking that would indicate improper rocker arm installation or lash adjuster issues.
  • Verify no oil leaks from valve covers or camshaft position sensors.
  • Check for diagnostic trouble codes related to camshaft position sensors using scan tool. Clear any codes and verify they do not return.
  • Allow engine to reach operating temperature and verify smooth idle and normal operation.
  • Perform test drive and verify normal engine performance, acceleration, and no misfires.
  • After 50-100 miles, recheck valve cover bolt torque and inspect for oil leaks.
  • Verify engine oil level is correct and top off if necessary after oil filter has filled.

Related trouble codes on this vehicle

Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.

Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →

🔧Stuck on this camshaft r&r? Take it to The Diag Desk.A human with 20+ years in the bay answers about YOUR Dodge within 24 hours — never AI. $25, and you're not charged unless you get an answer.Ask a tech →

More procedures for this vehicle

For shop owners
Want more customers to find you?
We build shop websites with online booking onto your schedule and your own online store.
Talk to the ownerSee what's included
Built by a shop owner. Talk to Chris, not a sales rep.
🔧 Built by master technician Chris Hackleman · Master Technician · 20+ years. Spot an error? Use the Help link above — a human reads every report.
Stuck on this repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
⚠ STILL BEHIND THE PAYWALL
The 2017 Dodge Viper repair data is incomplete because no one has sponsored it yet. For $99, we generate the full step-by-step procedures, then fact-check them with a second AI pass and your expert review. Your name on every procedure, permanently.
The same data would cost $169/mo from Mitchell1 or $30/year from ALLDATAdiy — and you'd be renting access, not freeing it. Sponsor once, free forever.
Sponsor the Dodge Viper — $99 →
Building an app?
Free API key: 10 requests/day, 100/month, no card required.
Get an API key →
Run a shop?
A free website, SEO and Google reviews with your shop software. Auto Shop Base Professional, $250/mo, with our labor times on every estimate.
See what's included →