Free API
8.4L V10•RWD•MANUAL•gas
Founding sponsor spot is openYour name on every procedure for this vehicle, permanently.Sponsor — $99 →
transmission

Transmission Rebuild - Manual

for 2017 Dodge Viper 8.4L V10 · RWD
Difficulty
Expert
Time
13.5 h
Tools
20
Steps
27
✓Fact-checked. Built from OLP's spec database, then independently fact-checked line by line with every correction applied. Master-tech sign-off by Chris Hackleman is queued. Cross-check torque values against the factory manual, and stop if anything looks unsafe. How our data is made.

Complete removal, disassembly, rebuild, and reinstallation of the Tremec T56 6-speed manual transmission in a 2008 Dodge Viper, including clutch access and driveline disconnection.

Warnings

⚠️The transmission weighs approximately 130 pounds. Use a transmission jack and ensure it is properly secured before removal to prevent crush injuries.
⚠️Support the engine with a support bar or hoist before removing transmission mounts. Engine movement can cause component damage or injury.
⚠The Viper exhaust system runs extremely close to transmission components. Allow exhaust to cool completely before beginning work.
⚠Mark all shims, bearing preload measurements, and gear position measurements during disassembly. Incorrect reassembly will cause premature failure.
ℹ️This procedure requires transmission rebuild experience. Internal gear timing and synchronizer assembly are critical to proper operation.

Tools required

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Fluids

  • Pennzoil Synchromesh 75W-90 — 4.2 qt

Preparation

  1. Park vehicle on level ground and engage parking brake
  2. Disconnect negative battery terminal
  3. Raise vehicle on lift to comfortable working height (exhaust and transmission must be accessible from below)
  4. Remove both rear wheels to access parking brake cables if needed for clearance
  5. Allow exhaust system to cool completely (minimum 2 hours after engine operation)
  6. Place drain pan under transmission drain plug location
  7. Gather all rebuild components and lay out on clean workspace for inspection

Procedure

  1. 1
    Drain transmission fluid
    Locate the transmission drain plug on the bottom of the transmission case. Remove the drain plug and allow fluid to drain completely into a suitable container. Inspect drained fluid for metal particles or debris indicating internal wear. Remove the fill plug on the side of the transmission case to ensure complete drainage.
  2. 2
    Remove exhaust system components
    Disconnect exhaust system at the collector flange behind the transmission. Remove the 4 bolts securing each collector flange. Support the exhaust system and remove the transmission crossover pipe and mufflers as an assembly. The exhaust runs very close to the transmission and must be removed for access. Set exhaust components aside safely.
  3. 3
    Disconnect driveshaft
    Mark the driveshaft flange orientation to the differential flange for reinstallation. Remove the 4 bolts securing the driveshaft to the rear differential flange. Support the driveshaft and slide it rearward to disengage the slip yoke from the transmission output shaft. Inspect the output shaft seal for leakage. Place a plastic bag over the transmission output housing to prevent fluid leakage.
  4. 4
    Disconnect shifter and electrical connections
    Inside the vehicle, remove the shift knob and shift boot. Disconnect the shift linkage from the transmission shifter assembly. On the transmission, disconnect the reverse light switch electrical connector and the vehicle speed sensor connector. Remove the clutch slave cylinder line from the clutch slave cylinder mounted on the bellhousing (do not disconnect the line from the cylinder itself; remove the cylinder as an assembly with the transmission).
  5. 5
    Support engine and remove crossmember
    Install an engine support bar across the engine compartment or attach an engine hoist to the engine lift points. Raise the support slightly to take weight off the transmission mount. Remove the transmission crossmember mount bolts (2 bolts on each side of the crossmember to the frame). Remove the transmission mount to crossmember fasteners. Lower and remove the crossmember from the vehicle.
  6. 6
    Remove bellhousing and transmission assembly
    Position a transmission jack under the transmission with the adapter properly supporting the transmission case. Secure the transmission to the jack with a strap or chain. Remove the bellhousing to engine block bolts (6 bolts total around the perimeter of the bellhousing). Carefully slide the transmission and bellhousing assembly straight back to disengage the input shaft from the clutch disc. Lower the transmission jack and maneuver the assembly out from under the vehicle. The clutch assembly is now accessible if replacement is needed.
  7. 7
    Separate transmission from bellhousing
    With the transmission on a workbench, remove the bolts securing the transmission case to the bellhousing (8 bolts). Carefully separate the transmission case from the bellhousing. Remove the clutch slave cylinder from the bellhousing and inspect for leakage. Place the transmission case on a transmission rebuild stand and secure it.
  8. 8
    Remove transmission tailhousing and extension
    Remove the bolts securing the tailhousing to the transmission case. Slide the tailhousing off the output shaft. Remove the output shaft seal and inspect the housing for cracks. Remove the speedometer drive gear or vehicle speed sensor housing from the tailhousing or case.
  9. 9
    Disassemble shift cover and forks
    Remove the shift cover bolts (typically 8-10 bolts) and lift the shift cover off the transmission case. Note the position and orientation of all shift forks and rails. Remove the shift fork retaining pins or bolts. Slide the shift rails out of the case while noting their positions. Remove the shift forks and inspect the fork pads for wear. Remove the detent springs and balls from the case, noting their positions.
  10. 10
    Remove front bearing retainer and input shaft
    Remove the bolts securing the front bearing retainer to the transmission case (4 bolts). Remove the front bearing retainer and input shaft seal. Using snap ring pliers, remove the input shaft bearing snap ring from inside the case. Carefully tap or pull the input shaft assembly forward out of the case. Inspect the input shaft bearing and gear teeth for wear.
  11. 11
    Remove counter shaft and output shaft assemblies
    Remove the counter shaft rear bearing retainer bolts and carefully slide out the counter shaft assembly from the rear of the case. The counter shaft contains multiple gears; support it as it exits to prevent dropping. Remove the output shaft rear bearing snap ring. Using a bearing puller or press, remove the output shaft assembly from the case by pulling it rearward. Keep all thrust washers, shims, and spacers in order as they are removed.
  12. 12
    Disassemble and inspect gear sets
    With all shafts removed, disassemble each shaft assembly individually on a clean workspace. Remove snap rings securing gears and synchronizer assemblies to the shafts. Use a press to remove bearings from shafts as needed. Inspect all gear teeth for chipping, pitting, or excessive wear. Measure synchronizer ring gap with feeler gauges; replace if gap exceeds specification (typically 0.020 inches minimum). Inspect all bearings for roughness or pitting. Measure shaft diameters with a micrometer for wear. Inspect shift fork grooves in synchronizer sleeves for wear.
  13. 13
    Clean and inspect transmission case
    Thoroughly clean the transmission case halves with solvent and compressed air. Inspect case for cracks, especially around bearing bores and bolt holes. Check all bearing bores for scoring or damage. Inspect the case machined mating surfaces for warping or damage. Replace the case if any cracks or significant damage is found.
  14. 14
    Reassemble gear sets on shafts
    Using the hydraulic press and appropriate adapters, install new bearings on the input shaft, output shaft, and counter shaft as applicable. Install gears on each shaft in the correct order with new synchronizer rings. Install new synchronizer assemblies ensuring the shift fork grooves are properly oriented. Secure all components with new snap rings. Measure end play on all gear sets with a dial indicator to ensure proper clearances are within specification (typically 0.003-0.010 inches). Install thrust washers and shims as required to achieve proper end play.
  15. 15
    Install output shaft and counter shaft into case
    Install the output shaft assembly into the transmission case from the rear. Install the output shaft rear bearing using a bearing driver or press. Install the rear bearing snap ring. Apply a thin coat of assembly lube to all gear surfaces. Install the counter shaft assembly into the case from the rear, aligning all gears properly with the output shaft gears. Install the counter shaft rear bearing retainer with new gasket and secure with bolts. Verify all gears rotate freely and mesh properly.
  16. 16
    Install input shaft and front bearing retainer
    Apply assembly lube to the input shaft bearing. Carefully insert the input shaft assembly into the front of the case, aligning it with the output shaft pilot bearing. Install the input shaft bearing snap ring. Apply RTV silicone to the front bearing retainer mating surface. Install a new input shaft seal in the bearing retainer. Install the front bearing retainer and secure with bolts.
  17. 17
    Install shift forks and rails
    Install the detent balls and springs into their bores in the case. Install the shift rails into the case in the correct positions. Install the shift forks onto the synchronizer sleeves in their proper positions. Align the shift rails through the shift forks and secure with retaining pins or bolts. Verify all forks move smoothly and engage their respective gears properly. Install new shift fork pads if removed.
  18. 18
    Install shift cover
    Apply RTV silicone or a new gasket to the shift cover mating surface. Carefully align the shift cover with the shift rails and lower it onto the transmission case. Install and tighten the shift cover bolts in a crisscross pattern. Verify the shift mechanism operates smoothly through all gears.
  19. 19
    Install tailhousing and output seal
    Install a new output shaft seal in the tailhousing using a seal driver. Apply RTV silicone or install a new gasket on the tailhousing mating surface. Slide the tailhousing onto the output shaft and align it with the case. Install and tighten the tailhousing bolts. Install the speedometer drive gear or vehicle speed sensor housing.
  20. 20
    Mate transmission to bellhousing
    Install a new clutch slave cylinder on the bellhousing. Apply a thin coat of high-temp grease to the input shaft splines. Apply RTV silicone or install a new gasket between the transmission case and bellhousing. Align the transmission case with the bellhousing and install the 8 retaining bolts. Tighten the bolts in a crisscross pattern.
  21. 21
    Install transmission assembly into vehicle
    Inspect the clutch disc, pressure plate, and flywheel while the transmission is out. Replace components as needed. Apply a small amount of high-temp grease to the pilot bearing in the crankshaft. Position the transmission and bellhousing assembly on the transmission jack and raise it into position under the vehicle. Align the input shaft with the clutch disc splines using the clutch alignment tool if needed. Carefully slide the transmission forward, ensuring the input shaft engages the clutch disc and pilot bearing. Install the bellhousing to engine block bolts and tighten in a crisscross pattern.
  22. 22
    Install crossmember and transmission mount
    Position the transmission crossmember under the transmission and loosely install the crossmember to frame bolts. Install the transmission mount to crossmember fasteners. Adjust the engine support to ensure proper alignment and remove any binding. Tighten all crossmember and mount fasteners. Remove the engine support bar or hoist.
  23. 23
    Reconnect driveshaft and shifter
    Remove the protective bag from the transmission output housing. Apply a small amount of grease to the output shaft splines. Slide the driveshaft slip yoke into the transmission output shaft, aligning the marks made during disassembly. Install the driveshaft to differential flange bolts and tighten. Inside the vehicle, reconnect the shift linkage to the transmission shifter assembly. Install the shift boot and shift knob.
  24. 24
    Reconnect electrical and hydraulic connections
    Reconnect the reverse light switch electrical connector and vehicle speed sensor connector on the transmission. Reconnect the clutch slave cylinder hydraulic line. Bleed the clutch hydraulic system if air was introduced.
  25. 25
    Reinstall exhaust system
    Position the exhaust system assembly under the vehicle. Install new gaskets at the collector flanges. Install the 4 bolts at each collector flange and tighten. Ensure the exhaust has proper clearance from the transmission and driveshaft throughout its length.
  26. 26
    Fill transmission with fluid
    Using a fluid pump, fill the transmission through the fill hole on the side of the transmission case with the OEM-specified quantity of Mopar/Tremec-approved manual transmission fluid (synchromesh MTF per the factory service manual). Fluid should reach the bottom of the fill hole. Install the fill plug.
  27. 27
    Final inspection and test
    Reinstall rear wheels if removed. Lower the vehicle to the ground. Reconnect the negative battery terminal. Start the engine and verify no leaks from the transmission, bellhousing, or hydraulic lines. With the engine running, depress the clutch pedal and shift through all gears to verify proper operation. Test drive the vehicle through all gears under light load, checking for smooth shifts, proper gear engagement, and no abnormal noises.

Reassembly

  1. Ensure all snap rings are fully seated in their grooves during reassembly
  2. Apply assembly lube to all bearing surfaces and gear contact points during rebuild
  3. Replace all seals, gaskets, and synchronizer rings regardless of appearance
  4. Verify proper gear end play measurements before final assembly
  5. Do not reuse thread locker; apply fresh medium-strength thread locker to appropriate fasteners
  6. Ensure shift forks are properly aligned in synchronizer grooves before installing shift cover
  7. Torque all fasteners in crisscross patterns where applicable to prevent case warping

Verification

  • Check for fluid leaks around all seals and gaskets after initial start and after test drive
  • Verify smooth clutch engagement with no chatter or slipping
  • Confirm all gears engage smoothly without grinding or resistance
  • Test that reverse lockout functions properly
  • Verify no abnormal noises (whining, grinding, rattling) in any gear or at any speed
  • Check that transmission shifts smoothly under acceleration and deceleration
  • Confirm proper operation of reverse lights
  • Verify transmission mount is secure with no excessive movement

Related trouble codes on this vehicle

Codes that commonly send this job to the bay — tap one for symptoms, causes, and diagnostic steps.

Chasing one of these codes and not sure which part is guilty? Ask a master mechanic about YOUR car →

🔧Stuck on this transmission rebuild - manual? Take it to The Diag Desk.A human with 20+ years in the bay answers about YOUR Dodge within 24 hours — never AI. $25, and you're not charged unless you get an answer.Ask a tech →

More procedures for this vehicle

For shop owners
Want more customers to find you?
We build shop websites with online booking onto your schedule and your own online store.
Talk to the ownerSee what's included
Built by a shop owner. Talk to Chris, not a sales rep.
🔧 Built by master technician Chris Hackleman · Master Technician · 20+ years. Spot an error? Use the Help link above — a human reads every report.
Stuck on this repair? Take it to The Diag Desk — ask a master tech about this exact car → real human answer within 24h, never AI
⚠ STILL BEHIND THE PAYWALL
The 2017 Dodge Viper repair data is incomplete because no one has sponsored it yet. For $99, we generate the full step-by-step procedures, then fact-check them with a second AI pass and your expert review. Your name on every procedure, permanently.
The same data would cost $169/mo from Mitchell1 or $30/year from ALLDATAdiy — and you'd be renting access, not freeing it. Sponsor once, free forever.
Sponsor the Dodge Viper — $99 →
Building an app?
Free API key: 10 requests/day, 100/month, no card required.
Get an API key →
Run a shop?
A free website, SEO and Google reviews with your shop software. Auto Shop Base Professional, $250/mo, with our labor times on every estimate.
See what's included →