body

Side Mirror Glass

for 2017 Dodge Viper 8.4L V10 · RWD

Difficulty

Easy

Time

30 min

Tools

Steps

🔍Draft — verification in progress. This procedure was built from OLP's spec database on September 13, 2026 and is queued for line-by-line review by Chris Hackleman — master technicians with 20+ years each. That review typically completes within 3 days of generation, and this banner changes to a verified badge the moment it does. Until then, cross-check every torque value and fluid capacity against the factory manual, and stop if anything looks unsafe. If something looks off, report it below — a real person reads every report.

Replace the side mirror glass on a 2008 Dodge Viper by removing the old glass from the mirror housing and installing a new glass assembly.

Warnings

⚠If the mirror glass is cracked or shattered, wear gloves and eye protection to avoid injury from sharp edges.

ℹ️Replacement glass must match the original specification (heated vs non-heated) to ensure proper fitment and function.

Tools required

Flathead screwdriver or trim removal toolEssential

Shop towel or cloth

Heat gun or hair dryer

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Parts

Side mirror glass × 1 — Specify left or right side, heated or non-heated

As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.

Preparation

Verify the correct replacement mirror glass for your side (driver or passenger) and mirror type (heated or non-heated).
Park the vehicle on a level surface and turn off the ignition.
If the glass is shattered, clean any loose glass fragments from the mirror housing and surrounding area.

Procedure

1
Access the mirror glass
Position yourself at the door with clear access to the side mirror. If equipped with power folding mirrors, ensure the mirror is in the extended position for easier access to the glass.
2
Prepare the glass for removal
If the existing mirror glass is intact and adhered firmly, use a heat gun or hair dryer to warm the edges of the glass for approximately 1-2 minutes. This softens any adhesive and makes removal easier. If the glass is already broken or loose, skip this heating step.
3
Release the mirror glass from the backing plate
The mirror glass is retained by clips on the backing plate behind the glass. Starting at one edge (typically the outer or lower edge), carefully insert a flathead screwdriver or trim removal tool between the mirror glass and the mirror housing. Apply gentle outward pressure to begin separating the glass from the clips. Work your way around the perimeter, releasing each clip point. The glass should have 2 to 4 clip attachment points depending on mirror design.
4
Disconnect the heated mirror connector (if equipped)
If the mirror is equipped with a heating element, as you pull the glass forward you will see a small electrical connector on the back of the glass assembly. Carefully disconnect this electrical connector by pressing the release tab and pulling the connector free. On non-heated mirrors, simply pull the glass assembly completely free from the housing once all clips are released.
5
Remove the old mirror glass
Once all clips are released and any electrical connection is disconnected, remove the old mirror glass assembly from the mirror housing. Inspect the mirror housing for any remaining adhesive, broken clip fragments, or debris and clean as necessary with a shop towel.
6
Prepare the new mirror glass
Remove the new mirror glass from its packaging. If equipped with a heated element, verify the electrical connector is accessible on the back of the new glass assembly. Check that the mounting clips or backing plate on the new glass match the configuration of the original.
7
Connect the heated mirror connector (if equipped)
If the mirror is heated, position the new glass assembly near the mirror housing and connect the electrical connector to the mating connector in the housing. Ensure the connection is secure and fully seated before proceeding.
8
Install the new mirror glass
Align the clips on the back of the new mirror glass assembly with the mounting points in the mirror housing. Starting with one edge, press the glass firmly into the housing until you hear or feel the first clip engage. Work your way around the perimeter, pressing firmly at each clip location until all clips are fully seated. The glass should sit flush and secure in the housing with no gaps or movement.

Reassembly

No disassembly was required beyond the mirror glass itself, so no additional reassembly steps are necessary.

Verification

Gently push on the edges of the new mirror glass to verify all clips are fully engaged and the glass does not move or flex excessively.
If equipped with heated mirrors, turn the ignition to the ON position and activate the heated mirror function to verify the heating element is working (you should feel warmth on the glass surface within 1-2 minutes).
Adjust the mirror through its full range of motion using the power mirror controls to ensure the glass remains secure during adjustment.
Visually inspect the mirror glass from multiple angles to ensure it is properly aligned and seated flush in the housing.