Fitment notes: AGM battery required for e-Power hybrid system; battery located in engine bay
As an Amazon Associate and Autel/ANCEL partner, OLP earns from qualifying purchases — how we link. This never changes the specs we publish.
Control Modules — 2026 Nissan X-Trail JP
Every control module on the 2021-2026 Nissan X-Trail JP — where it lives, replacement time, and what it takes to program a replacement. Modules marked dealer / factory tool won't work after a part swap alone — budget for programming.
📍 Integrated with valve body inside CVT transmission, accessed from underneath vehicle after pan removal
🔧 CONSULT-III Plus with NTIS subscription
⚠️ CVT adaptive values must be reset; transmission fluid replacement required during R&R; VIN and ECM pairing mandatory; enhanced security on 2021+ models
Electric Power Steering Control Module (EPS)2.2 hr R&Raftermarket tool +0.4 hr▸ programming details
📍 Integrated with steering column assembly, accessed from below driver side dash after lower panel removal
🔧 Autel MaxiSys or CONSULT-III Plus for steering angle sensor calibration
⚠️ Steering angle sensor zero-point calibration mandatory after replacement; front wheels must be centered during procedure
Anti-lock Brake System Control Module (ABS)1.8 hr R&Raftermarket tool +0.3 hr▸ programming details
📍 Engine compartment, driver side inner fender well, mounted to hydraulic unit
🔧 Autel MaxiSys or Launch X431 for brake bleed procedure
⚠️ Integrated with hydraulic unit; brake bleeding via scan tool required after replacement; VIN coding not mandatory but recommended
Around View Monitor Control Module (AVM)1.6 hr R&Rdealer / factory tool +0.8 hrwith Around View Monitor (360-degree camera)▸ programming details
📍 Behind center display screen, integrated with or adjacent to AVN unit in center stack
🔧 CONSULT-III Plus with camera calibration procedure
⚠️ Camera alignment and stitching calibration required; calibration mat or specific parking space markings needed for proper setup
📍 Behind center touchscreen display in dashboard, accessed after center stack trim and screen removal
🔧 Autel or CONSULT-III Plus for vehicle settings transfer
⚠️ Navigation SD card separate; steering wheel control adaptation and camera input configuration required; 2021+ models feature updated NissanConnect interface with wireless Apple CarPlay/Android Auto
Body Control Module (BCM)1.5 hr R&Rdealer / factory tool +1.2 hr▸ programming details
📍 Behind driver side lower dash panel, above fuse box, left of steering column
🔧 CONSULT-III Plus with NTIS subscription
⚠️ Controls central locking, lighting, wiper functions; all Intelligent Keys must be re-registered after replacement; configuration includes market-specific lighting and feature settings; gateway security functions integrated
📍 Integrated within Intelligent Power Distribution Module in engine compartment, driver side fender well
🔧 CONSULT-III Plus with NTIS subscription
⚠️ All Intelligent Key fobs must be re-registered; ECM and BCM pairing required; 2021+ enhanced security makes aftermarket key programming significantly more difficult
Transfer Control Module (TCCM)1.4 hr R&Raftermarket tool +0.3 hrAWD models▸ programming details
📍 Under vehicle, mounted to transfer case assembly, accessed from underneath
🔧 Autel or CONSULT-III Plus for 4WD system initialization
⚠️ 4WD system initialization and coupling calibration required; test drive in various modes recommended after replacement
Automatic Air Conditioning Control Module (A/C)1.3 hr R&Rrelearn only +0.1 hr▸ programming details
📍 Behind center stack climate control panel, accessible after radio and climate control bezel removal
🔧 Self-relearn via button sequence or basic scan tool
⚠️ Actuator relearn procedure required after installation; dual-zone systems have single control module
Radar Control Module (RADAR)1.3 hr R&Rdealer / factory tool +1.0 hrwith ProPILOT Assist or Intelligent Cruise Control▸ programming details
📍 Behind front grille, center position behind Nissan emblem, accessed after grille removal
🔧 CONSULT-III Plus with radar aiming tool and target
⚠️ Radar aiming calibration mandatory after replacement or front-end collision repair; requires specific alignment targets and level surface
📍 Engine compartment, passenger side firewall, mounted on bulkhead below windshield cowl
🔧 CONSULT-III Plus with NTIS subscription
⚠️ VIN programming and immobilizer pairing required; enhanced security gateway protection on 2021+ models increases aftermarket programming difficulty
Intelligent Power Distribution Module (IPDM)1.2 hr R&Raftermarket tool +0.2 hr▸ programming details
📍 Engine compartment, driver side inner fender well, black box with multiple large connectors
🔧 Autel or CONSULT-III Plus for system initialization
⚠️ Integrates fuel pump relay, cooling fan control, and multiple power distribution functions; basic relearn typically sufficient but dealer tool recommended for full configuration
📍 Behind driver side lower dash panel, mounted to body harness junction block near BCM
🔧 CONSULT-III Plus with NTIS subscription
⚠️ Manages CAN bus communication between networks; replacement requires VIN and network configuration programming; enhanced security gateway functions on 2021+ models restrict aftermarket access to certain modules
Power Back Door Control Module (PBD)1.1 hr R&Raftermarket tool +0.3 hrwith power liftgate▸ programming details
📍 Inside liftgate, driver side lower corner, behind interior trim panel
🔧 Autel or CONSULT-III Plus for height memory and pinch protection calibration
⚠️ Height position memory and obstacle detection calibration required; kick sensor (if equipped) must be paired
⚠️ Odometer programming requires dealer tool and legal documentation; VIN and vehicle configuration must be programmed; 2021+ models have enhanced digital display options
Power Window Master Switch (PWMS)0.6 hr R&Rrelearn only +0.1 hr▸ programming details
📍 Integrated into driver door master switch assembly, in driver door armrest
🔧 Window auto-up/down relearn via switch procedure
⚠️ Window auto-up/down limits must be relearned for all windows after replacement; simple switch-based procedure
Aftermarket tool coverage varies by software version and vehicle build — treat "aftermarket tool" rows as "usually possible" and verify against your tool maker's coverage list before promising a customer. Spot a wrong location or hour? Tell us — corrections ship fast here.
📝 2026 model year data based on projected continuation of current generation (T33) specifications. Japanese market X-Trail typically uses these dimensions.
2026 model year data based on projected continuation of current generation (T33) specifications. Japanese market X-Trail typically uses these dimensions.
Size-standard part numbers — verify your connector type before buying. Rear blades are model-specific; check the package's vehicle list.
Fuel economy figures are EPA data via fueleconomy.gov (median across matching trims). Performance figures are compiled estimates for the 2026 Nissan X-Trail JP 1.5L I3 Turbo e-Power and can vary by trim.
🔧 Built by master technician Chris Hackleman · Master Technician · 20+ years.